User Manual
Table Of Contents
- Your new tumble dryer
- Display rules
- Contentsen Installation and operating instructions
- 8 Intended use 4
- ( Safety instructions 4
- 7 Environmental protection 12
- 5 Installation and connection 13
- ΠDraining the condensation water 15
- Y The main points in brief 17
- * Getting to know your appliance 18
- Z Laundry 21
- / Programmes and buttons 22
- 1 Operating the appliance 25
- M Signal setting 28
- D Cleaning 29
- 3 Faults and what to do about them 31
- J After-sales service 33
- [ Consumption values 34
- J Technical data 35
- 8 Intended use
- ( Safety instructions
- Safety instructions
- Children/people/pets
- Installation
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of fire/material damage/ damage to the appliance!
- : Warning
- Risk of injury/material damage/damage to the appliance!
- : Warning
- Risk of injury!
- Operation
- Cleaning/Maintenance
- 7 Environmental protection
- 5 Installation and connection
- 2. Press the Start button.
- 3. Wait for 5 minutes.
- 4. Empty the condensate container again.
- 5. Switch off the dryer.
- 2. When the dryer is delivered from the factory, the hose for discharging the condensation into the condensation container is fastened to the connecting piece.
- 3. Detach the condensation hose from the socket.
- 4. Place the condensation hose in the "parked" position.
- 5. Take the drain hose from the accessories and secure it to the free connecting piece.
- 6. Fasten the other end of the drain hose with the remaining accessories, depending on the connection situation (A, B or C).
- Buttons in the display panel
- Display panel
- Do not tumble-dry the following fabrics:
- / Programmes and buttons
- 1 Operating the appliance
- 2. Turn the programme selector to any programme to switch the dryer on.
- 3. Close the dryer door.
- 2. Use the programme selector to set the required programme. The default programme settings for the selected programme appear in the display panel.
- 3. If required, adjust the default programme settings. You can find detailed information on this from ~ Page 22 onwards.
- 2. Add or remove laundry.
- 3. Select another programme or an additional function, if required.
- 4. Close the dryer door.
- 5. Press the Start button.
- 2. Turn the programme selector to the "off" position.
- 2. Remove the fluff filter.
- 3. Remove the fluff from the recess in the fluff filter.
- 4. Open the fluff filter and remove all the fluff.
- 5. Rinse away the fluff under running water or clean the fluff filter in the dishwasher.
- 6. Dry the fluff filter, close it and reinsert the fluff filter.
- 2. Pour out the condensation water.
- 3. Push in the condensate container until you feel it lock back into place in the dryer.
- Activating setting mode
- 1. Switch the dryer on.
- 2. Select the "Cottons" programme in position 1 and wait for five seconds.
- 2. The spin speed is shown in the display.
- 3. Press the "Ready in" time button or the drying time button to change the spin speed.
- 4. Turn the programme selector clockwise to position 3.
- 5. The volume of the audible signal at the end of the programme is shown in the display.
- 6. Press the "Ready in" time button or the drying time button to change the volume.
- 7. Turn the programme selector clockwise to position 4.
- 8. The volume for the audible button signal is shown in the display.
- 9. Press the "Ready in" time button or the drying time button to change the volume.
- 2. Open the maintenance flap fully.
- 3. Turn both locking levers towards each other.
- 4. Remove the top cap from the heat exchanger.
- 5. Remove the heat exchanger.
- 6. Flush water through the heat exchanger from all sides to completely remove all fluff.
- 7. Remove all fluff from the seals on the dryer and on the heat exchanger.
- 8. Allow all the water to drip off.
- 9. First insert the heat exchanger, and then fit the heat exchanger's top cap in place.
- 10. Turn both locking levers back and close the maintenance flap until it locks into place.
- 11. Close the maintenance flap and press on it until you feel it click in place.
- Cleaning the moisture sensor
- 3 Faults and what to do about them
- J After-sales service
- [ Consumption values
- 9 kg
- 4.5 kg
- 9 kg
- 4.5 kg
- 1400 rpm
- 129 min
- 69 min
- 4.36 kWh
- 2.31 kWh
- 1000 rpm
- 150 min
- 80 min
- 5.23 kWh
- 2.77 kWh
- 800 rpm
- 181 min
- 91 min
- 6.02 kWh
- 3.19 kWh
- 1400 rpm
- 106 min
- 54 min
- 2.61 kWh
- 1.38 kWh
- 1000 rpm
- 127 min
- 65 min
- 4.01 kWh
- 2.12 kWh
- 800 rpm
- 147 min
- 76 min
- 4.50 kWh
- 2.38 kWh
- 3.5 kg
- 3.5 kg
- 800 rpm
- 46 min
- 1.42 kWh
- 600 rpm
- 56 min
- 1.74 kWh
Draining the condensation water en
15
ΠDraining the
condensation water
Draining the condensation water
Condensation will form in the appliance
as it dries the laundry.
You must ensure that the drain hose is
connected when you operate the
appliance.
If there is no drain hose connected to
the appliance, the condensation water
from the appliance will run into the
condensation container. In this case,
you will need to empty the condensation
container each time the dryer finishes
drying the laundry, and also if it
becomes full before drying is complete.
Connect the drain hose as follows:
1. Remove the accessories from the
dryer drum.
2. When the dryer is delivered from the
factory, the hose for discharging the
condensation into the condensation
container is fastened to the
connecting piece.
3. Detach the condensation hose from
the socket.
4. Place the condensation hose in the
"parked" position.
5. Take the drain hose from the
accessories and secure it to the free
connecting piece.