User Manual
Table Of Contents
- Your new tumble dryer
- Display rules
- Contentsen Installation and operating instructions
- 8 Intended use 4
- ( Safety instructions 4
- 7 Environmental protection 12
- 5 Installation and connection 13
- ΠDraining the condensation water 15
- Y The main points in brief 17
- * Getting to know your appliance 18
- Z Laundry 21
- / Programmes and buttons 22
- 1 Operating the appliance 25
- M Signal setting 29
- D Cleaning 30
- 3 Faults and what to do about them 32
- J After-sales service 34
- [ Consumption values 35
- J Technical data 36
- 8 Intended use
- ( Safety instructions
- Safety instructions
- Children/people/pets
- Installation
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of fire/material damage/ damage to the appliance!
- : Warning
- Risk of injury/material damage/damage to the appliance!
- : Warning
- Risk of injury!
- Operation
- Cleaning/Maintenance
- 7 Environmental protection
- 5 Installation and connection
- 2. Press the Start button.
- 3. Wait for 5 minutes.
- 4. Empty the condensate container again.
- 5. Switch off the dryer.
- 2. When the dryer is delivered from the factory, the hose for discharging the condensation into the condensation container is fastened to the connecting piece.
- 3. Detach the condensation hose from the socket.
- 4. Place the condensation hose in the "parked" position.
- 5. Take the drain hose from the accessories and secure it to the free connecting piece.
- 6. Fasten the other end of the drain hose with the remaining accessories, depending on the connection situation (A, B or C).
- Buttons in the display panel
- Display panel
- Do not tumble-dry the following fabrics:
- / Programmes and buttons
- 1 Operating the appliance
- 2. Turn the programme selector to any programme to switch the dryer on.
- 3. Close the dryer door.
- 2. Use the programme selector to set the required programme. The default programme settings for the selected programme appear in the display panel.
- 3. If required, adjust the default programme settings. You can find detailed information on this from ~ Page 22 onwards.
- 2. Add or remove laundry.
- 3. Select another programme or an additional function, if required.
- 4. Close the dryer door.
- 5. Press the Start button.
- 2. Turn the programme selector to the "off" position.
- 2. Remove the fluff filter.
- 3. Remove the fluff from the recess in the fluff filter.
- 4. Open the fluff filter and remove all the fluff.
- 5. Rinse away the fluff under running water or clean the fluff filter in the dishwasher.
- 6. Dry the fluff filter, close it and reinsert the fluff filter.
- 2. Pour out the condensation water.
- 3. Push in the condensate container until you feel it lock back into place in the dryer.
- Activating setting mode
- 1. Switch the dryer on.
- 2. Select the "Cottons" programme in position 1 and wait for five seconds.
- 2. The spin speed is shown in the display.
- 3. Press the "Ready in" time button or the drying time button to change the spin speed.
- 4. Turn the programme selector clockwise to position 3.
- 5. The volume of the audible signal at the end of the programme is shown in the display.
- 6. Press the "Ready in" time button or the drying time button to change the volume.
- 7. Turn the programme selector clockwise to position 4.
- 8. The volume for the audible button signal is shown in the display.
- 9. Press the "Ready in" time button or the drying time button to change the volume.
- 2. Open the maintenance flap fully.
- 3. Turn both locking levers towards each other.
- 4. Remove the top cap from the heat exchanger.
- 5. Remove the heat exchanger.
- 6. Flush water through the heat exchanger from all sides to completely remove all fluff.
- 7. Remove all fluff from the seals on the dryer and on the heat exchanger.
- 8. Allow all the water to drip off.
- 9. First insert the heat exchanger, and then fit the heat exchanger's top cap in place.
- 10. Turn both locking levers back and close the maintenance flap until it locks into place.
- 11. Close the maintenance flap and press on it until you feel it click in place.
- Cleaning the moisture sensor
- 3 Faults and what to do about them
- J After-sales service
- [ Consumption values
- 9 kg
- 4.5 kg
- 9 kg
- 4.5 kg
- 1400 rpm
- 129 min
- 69 min
- 4.36 kWh
- 2.31 kWh
- 1000 rpm
- 150 min
- 80 min
- 5.23 kWh
- 2.77 kWh
- 800 rpm
- 181 min
- 91 min
- 6.02 kWh
- 3.19 kWh
- 1400 rpm
- 106 min
- 54 min
- 2.61 kWh
- 1.38 kWh
- 1000 rpm
- 127 min
- 65 min
- 4.01 kWh
- 2.12 kWh
- 800 rpm
- 147 min
- 76 min
- 4.50 kWh
- 2.38 kWh
- 3.5 kg
- 3.5 kg
- 800 rpm
- 46 min
- 1.42 kWh
- 600 rpm
- 56 min
- 1.74 kWh
en Operating the appliance
26
Programme sequence
The programme status is indicated in
the display field.
Changing the programme or
adding laundry
You can remove or add laundry and
change or alter the programme at any
time during drying.
1. To pause the programme, open the
dryer door or press the Start button.
2. Add or remove laundry.
3. Select another programme or an
additional function, if required.
4. Close the dryer door.
5. Press the Start button.
Note: The programme duration in the
display panel is updated depending on
the load and residual moisture in the
laundry. The values displayed may
change after the programme is
changed or the load is adapted.
Cancelling the programme
The programme can be interrupted at
any time; to pause, open the dryer door
or press the Start button.
Caution!
Risk of fire. Laundry may catch fire.
If you cancel the programme, you must
remove the laundry items and spread
them out so that the heat can disperse.
Programme end
“Ÿš appears in the display panel.
Removing laundry and
switching off the dryer
1. Remove the laundry.
2. Turn the programme selector to the
"off" position.
e.g.
1:27
Expected programme duration
in hours and minutes.
Note: When a programme is
selected, the expected drying
time for the recommended load
is displayed. During drying
moisture sensors detect the
remaining moisture in the load
and adjust the programme
length (except timed
programmes). This is visible via
the time remaining leaping
forward.
Ù Dry
ö Iron Dry
» Cupboard Dry
Q AntiCrease
- ˜ -
Pause
“Ÿš End