User Manual
Table Of Contents
- Your new tumble dryer
- Display rules
- Contentsen Installation and operating instructions
- 8 Intended use 4
- ( Safety instructions 4
- 7 Environmental protection 12
- 5 Installation and connection 13
- ΠDraining the condensation water 15
- Y The main points in brief 17
- * Getting to know your appliance 18
- Z Laundry 21
- / Programmes and buttons 22
- 1 Operating the appliance 25
- M Signal setting 29
- D Cleaning 30
- 3 Faults and what to do about them 32
- J After-sales service 34
- [ Consumption values 35
- J Technical data 36
- 8 Intended use
- ( Safety instructions
- Safety instructions
- Children/people/pets
- Installation
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of fire/material damage/ damage to the appliance!
- : Warning
- Risk of injury/material damage/damage to the appliance!
- : Warning
- Risk of injury!
- Operation
- Cleaning/Maintenance
- 7 Environmental protection
- 5 Installation and connection
- 2. Press the Start button.
- 3. Wait for 5 minutes.
- 4. Empty the condensate container again.
- 5. Switch off the dryer.
- 2. When the dryer is delivered from the factory, the hose for discharging the condensation into the condensation container is fastened to the connecting piece.
- 3. Detach the condensation hose from the socket.
- 4. Place the condensation hose in the "parked" position.
- 5. Take the drain hose from the accessories and secure it to the free connecting piece.
- 6. Fasten the other end of the drain hose with the remaining accessories, depending on the connection situation (A, B or C).
- Buttons in the display panel
- Display panel
- Do not tumble-dry the following fabrics:
- / Programmes and buttons
- 1 Operating the appliance
- 2. Turn the programme selector to any programme to switch the dryer on.
- 3. Close the dryer door.
- 2. Use the programme selector to set the required programme. The default programme settings for the selected programme appear in the display panel.
- 3. If required, adjust the default programme settings. You can find detailed information on this from ~ Page 22 onwards.
- 2. Add or remove laundry.
- 3. Select another programme or an additional function, if required.
- 4. Close the dryer door.
- 5. Press the Start button.
- 2. Turn the programme selector to the "off" position.
- 2. Remove the fluff filter.
- 3. Remove the fluff from the recess in the fluff filter.
- 4. Open the fluff filter and remove all the fluff.
- 5. Rinse away the fluff under running water or clean the fluff filter in the dishwasher.
- 6. Dry the fluff filter, close it and reinsert the fluff filter.
- 2. Pour out the condensation water.
- 3. Push in the condensate container until you feel it lock back into place in the dryer.
- Activating setting mode
- 1. Switch the dryer on.
- 2. Select the "Cottons" programme in position 1 and wait for five seconds.
- 2. The spin speed is shown in the display.
- 3. Press the "Ready in" time button or the drying time button to change the spin speed.
- 4. Turn the programme selector clockwise to position 3.
- 5. The volume of the audible signal at the end of the programme is shown in the display.
- 6. Press the "Ready in" time button or the drying time button to change the volume.
- 7. Turn the programme selector clockwise to position 4.
- 8. The volume for the audible button signal is shown in the display.
- 9. Press the "Ready in" time button or the drying time button to change the volume.
- 2. Open the maintenance flap fully.
- 3. Turn both locking levers towards each other.
- 4. Remove the top cap from the heat exchanger.
- 5. Remove the heat exchanger.
- 6. Flush water through the heat exchanger from all sides to completely remove all fluff.
- 7. Remove all fluff from the seals on the dryer and on the heat exchanger.
- 8. Allow all the water to drip off.
- 9. First insert the heat exchanger, and then fit the heat exchanger's top cap in place.
- 10. Turn both locking levers back and close the maintenance flap until it locks into place.
- 11. Close the maintenance flap and press on it until you feel it click in place.
- Cleaning the moisture sensor
- 3 Faults and what to do about them
- J After-sales service
- [ Consumption values
- 9 kg
- 4.5 kg
- 9 kg
- 4.5 kg
- 1400 rpm
- 129 min
- 69 min
- 4.36 kWh
- 2.31 kWh
- 1000 rpm
- 150 min
- 80 min
- 5.23 kWh
- 2.77 kWh
- 800 rpm
- 181 min
- 91 min
- 6.02 kWh
- 3.19 kWh
- 1400 rpm
- 106 min
- 54 min
- 2.61 kWh
- 1.38 kWh
- 1000 rpm
- 127 min
- 65 min
- 4.01 kWh
- 2.12 kWh
- 800 rpm
- 147 min
- 76 min
- 4.50 kWh
- 2.38 kWh
- 3.5 kg
- 3.5 kg
- 800 rpm
- 46 min
- 1.42 kWh
- 600 rpm
- 56 min
- 1.74 kWh
