Operation Manual
Table Of Contents
- ( Safety instructions 5
- 7 Protection of the environment 9
- * Getting to know your appliance 10
- + Water softening system/ Special salt 11
- , Rinse aid 13
- - Utensils 14
- . Detergent 18
- / Overview of programmes 20
- 0 Additional options 21
- 1 Operating the appliance 22
- 2 Cleaning and maintenance 27
- 3 Fault, what to do? 29
- 4 Customer service 39
- 5 Installation and connection 39
- 8 Intended use
- Intended use
- ■ This appliance is intended for use in the home and domestic environments.
- ■ Use the dishwasher only in the home and only for its designated purpose: for washing domestic dishes.
- ■ This appliance is intended for use up to a maximum altitude of 4000 metres above sea level.
- ( Safety instructions
- This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capabilities or by persons with a lack of experience or knowledge if they are supervised or are instructed by a person responsi...
- Children must not play with, on, or around the appliance. Children must not clean the appliance or carry out general maintenance unless they are at least 8 years old and are being supervised.
- Keep children below the age of 8 years old at a safe distance from the appliance and power cable.
- Before you switch ON the appliance
- Please read the instructions for use and installation carefully. They contain important information on how to install, use and maintain the appliance.
- Retain all documents for later use or for the subsequent owner.
- You can download the instructions for use from our website free of charge. The relevant Internet address can be found overleaf on these instructions for use.
- Delivery
- 1. Check the packaging and dishwasher immediately for damage caused in transit. Do not switch on a damaged appliance, but contact your supplier.
- 2. Please dispose of the packaging material in an environmentally friendly manner.
- 3. Do not let children play with packaging and its parts. There is a risk of suffocation from collapsible boxes and film.
- Installation
- ■ Following installation, ensure that the back of the dishwasher is not freely accessible (protection against contact due to hot surface).
- ■ Install and connect the appliance according to the installation and assembly instructions.
- ■ Prior to installation, disconnect the dishwasher from the power supply.
- ■ Ensure that the protective conductor system of the domestic supply has been correctly installed.
- ■ The electrical connection conditions must correspond with the specifications on the dishwasher rating plate 92.
- ■ If the power cord of this appliance is damaged, it must be replaced with a particular power cord.
- ■ If the dishwasher is installed in a high-sided unit, the unit must be secured properly.
- ■ If the dishwasher is installed below or above other domestic appliances, follow the information for installation in combination with a dishwasher in the installation instructions for the particular appliances.
- ■ Also follow the installation instructions for the dishwasher to ensure that all appliances are operated safely.
- ■ If there is no information or if the installation instructions do not include the appropriate information, contact the manufacturer of these appliances to ensure that the dishwasher can be installed above or below these appliances.
- ■ If you cannot obtain any information from the manufacturer, you must not install the dishwasher above or below these appliances.
- ■ If you install a microwave oven above the dishwasher, the microwave oven may be damaged.
- ■ Install built-under or integratable appliances only under continuous worktops which have been screwed to adjacent cupboards to ensure stability.
- ■ Do not install the appliance near heat sources (radiators, heat storage tanks, cookers or other appliances which generate heat) and do not install under a hob.
- ■ After installing the appliance, ensure that the plug is easily accessible.
- ■ Some models:
- In daily use
- Childproof lock (door lock)Door lock *
- Damage
- ■ The appliance may be repaired and opened up by a technician only. To do this, disconnect the appliance from the power supply. Pull out the mains plug or switch off the fuse. Turn off the tap.
- ■ If the appliance is damaged, especially the fascia (cracks, holes, broken buttons), or the door function is impaired, stop operating the appliance. Pull out mains plug or switch off fuse. Turn off tap, call customer service.
- Disposal
- 7 Protection of the environment
- Protection of the environment
- Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials.
- Please dispose of the individual parts separated according to type.
- Please ask your dealer or inquire at your local authority about current means of disposal.
- Packaging
- Old appliances
- Please follow the safety instructions under “Disposal of your appliance”.
- This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment - WEEE). The guideline determines the framework for the return and recycling o...
- * Getting to know your appliance
- Getting to know your appliance
- Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front.
- Individual positions are referred to in the text.
- Eco drying
- Control panel
- Appliance interior
- Overview of menu
- The settings can be found in the individual chapters.
- Water Hardness •:‹‹ - •:‹ˆ
- Intensive drying š:‹‹ - š:‹‚
- Rinse aid §:‹‹ - §:‹‡
- Hot water ‘:‹‹ - ‘:‹‚*
- End of programme buzzing sound ›:‹‹ - ›:‹„
- Automatic disconnection ˜:‹‹ - ˜:‹ƒ
- Optical display while the programme is running †:‹‹–†:‹ƒ
- Eco drying. Automatic door opening ©:‹‹ - ©:‹‚
- * depending on model
- + Water softening system/Special salt
- Water softening system/Special salt
- To ensure good washing results, the dishwasher requires soft water, i.e. containing low amounts of lime, otherwise white limescale will be deposited on the utensils and inner container.
- Tap water above 1.2 mmol/l must be softened. The water is softened with special salt (regeneration salt) in the water softening system of the dishwasher.
- The setting and therefore the required amount of salt depends on the degree of hardness of your tap water (see table).
- Setting
- The amount of salt dispensed can be set from •:‹‹ to •:‹ˆ.
- Salt is not required at the set value •:‹‹.
- 2. Set value can be found in the water hardness table.
- 3. Open the door.
- 4. Switch on ON/OFF switch (.
- 5. Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display.
- 6. Release both buttons.
- 2. Press START button `.
- 3. Close the door.
- Water hardness table
- Using special salt
- Always refill with special salt immediately before switching on the appliance. This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank.
- 2. Fill the tank with water (only required when switching on the appliance for the first time).
- 3. Then add dishwasher salt (not table salt or tablets).
- Using detergents with salt componentDetergents with salt component
- Switching off salt refill indicator/water softening systemSwitching off water softening system
- , Rinse aid
- Rinse aid
- As soon as the rinse-aid refill indicator H is lit on the fascia, there is still a rinse-aid reserve of 1-2 rinsing processes. Refill with rinse aid.
- The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers.
- Combined detergents with rinse-aid component may be used up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l) only. If the water hardness is over 21° dH, rinse aid must be used.
- 2. Carefully pour rinse aid up to the max. mark in the filler opening.
- 3. Close cover until it clicks shut.
- 4. To prevent excessive foam formation during the next rinse cycle, remove any rinse aid which has run over with a cloth.
- Setting amount of rinse aid
- The amount of rinse aid can be set from §:‹‹ to §:‹‡. Please set rinse aid on §:‹… to obtain very good drying results (§:‹… is already set in factory).
- Do not change the amount of rinse aid unless streaks (select lower setting) or water stains (select higher setting) are left on the utensils.
- 2. Switch on ON/OFF switch (.
- 3. Hold down programme button # and press START button ` until •:‹... is indicated on the digital display.
- 4. Release both buttons.
- 5. Press programme button # until the factory set value §:‹… is indicated on the digital display h.
- 2. Press START button `.
- 3. Close the door.
- Switching off rinse aid refill indicator
- - Utensils
- Utensils
- Not suitable
- Glass and utensil damage
- Causes:
- ■ Glass type and glass production process.
- ■ Chemical composition of the detergent.
- ■ Water temperature of the wash programme.
- ■ Use only glasses and porcelain which the manufacturer designates as dishwasher-proof.
- ■ Use a detergent which protects utensils.
- ■ Take glass and cutlery out of the dishwasher as soon as possible after the programme ends.
- Loading the dishwasher
- Unloading the dishwasher
- To prevent water from dripping off the upper basket onto the utensils in the lower basket, it is recommended to empty the appliance from the bottom up.
- Hot utensils are sensitive to shock! Therefore, when the programme ends, leave the utensils to cool down in the dishwasher until they can be handled.
- Cups and glasses
- Pans
- Cutlery drawer
- Arrange the cutlery in the cutlery drawer 1* as illustrated. Separately arranged cutlery is easier to remove after washing.
- The drawer can be taken out.
- Depending on the model, you can fold down the side shelves to provide more room for taller items of cutlery. The front rows of prongs can be folded down to provide room for wider handles.
- Folding spikesFolding spikes *
- Small accessories holder *Small accessories holder
- Adjusting the height of the basket
- The height of the upper utensils basket 12 can be adjusted in 3 stages to create more space either in the upper or lower basket.
- 2. To lower the basket, press in the left and then the right lever on the outside of the basket. In doing so, hold the sides of the basket along the upper edge to prevent it from suddenly dropping.
- 3. To raise the basket, hold the basket on the sides of the upper edge and lift it up.
- 4. Before re-inserting the basket again, ensure that it is at the same height on both sides. Otherwise, the appliance door cannot be closed and the upper spray arm will not be connected to the water circuit.
- . Detergent
- Detergent
- You can use tablets as well as powder or liquid detergents for dishwashers, but never use washing up liquid. The dosage can be individually adjusted with powder or a liquid detergent according to the degree of soiling. Tablets contain an adequately l...
- Adding detergent
- Combination detergent
- Apart from conventional detergents (Solo), a number of products are offered with additional functions. These products contain not only the detergent but also rinse-aid and salt replacement substances (3in1) and, depending on the combination (4in1, 5i...
- As soon as combined detergents are used, the rinse programme is adjusted automatically to ensure the best possible rinsing and drying result.
- / Overview of programmes
- Overview of programmes
- The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
- Programme selection
- Information for test institutes
- Test institutes receive the information for comparability tests (e.g. according to EN60436).
- These are the conditions for conducting the tests, however these are not the results or consumption values.
- Request by e-mail to:
- dishwasher@test-appliances.com
- The product number (E no.) and the production number (FD) are required which you can find on the rating plate 92 on the appliance door.
- 0 Additional options
- Additional options
- * depending on model
- Additional options can be set with the buttons X.
- Å Express WashPlus/ Speed PerfectPlus (VarioSpeedPlus) *Express WashPlus/SpeedPerfectPlus (VarioSpeedPlus)
- Half load§ Half load *
- µ HygienePlus *HygienePlus
- Ï Intensive zone *Intensive zone
- ¿ Extra drying *Extra drying
- 1 Operating the appliance
- Operating the appliance
- Programme data
- Aqua sensorAqua sensor *
- * depending on model
- The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water.
- The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drai...
- Switching on the appliance
- Eco drying
- If you have selected the Eco 50° programme, the door opens automatically when the programme ends. This ensures a particularly economical drying result. You can switch Eco drying on or off.
- 2. Switch on ON/OFF switch (.
- 3. Hold down programme button # and press START button ` until •:‹... is indicated on the digital display.
- 4. Release both buttons.
- 5. Press programme button # until the factory set value ©:‹‚ is indicated on the digital display h.
- 2. Press START button `.
- 3. Close the door.
- Optical display while the programme is running *Optical display while the programme is running
- * depending on model
- While the programme is running, an optical display is indicated on the floor under the appliance door.
- If the base panel is pulled forwards or if the appliance is installed at eye- level with flush furniture front, the display is not visible.
- Possible settings of the optical display:
- The display is switched off.
- Programme, timer programming, remaining time, end of programme and, if required, low water level are displayed.
- Same as †:‹‚. Other programme information is also displayed, e.g. the symbol for half load § or glass protection system active W.
- †:‹‚ is set at the factory.
- 2. Switch on ON/OFF switch (.
- 3. Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display.
- 4. Release both buttons.
- 5. Keep pressing programme button # until the previously set value, e.g. †:‹‚, is indicated on the digital display h †:‹... (for the optical display).
- 6. Keep pressing programme button 3 until the required value, e.g. †:‹ƒ, is indicated on the digital display h.
- 7. Press START button `.
- 8. Close the door.
- Remaining running time display
- When the programme is selected, the programme running time is indicated on the digital display h. When the programme has started, the remaining running time is displayed on the floor (only for settings †:‹‚ and †:‹ƒ).
- The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme).
- Timer programmingTimer programming *
- * depending on model
- You can delay the start of the programme in 1-hour steps up to 24 hours.
- 2. Switch on ON/OFF switch (.
- 3. Press button P + until the digital display h jumps to œ:‹‚.
- 4. Press P + or – button until the displayed time corresponds with your requirements.
- 5. Press START button `, timer programming is activated.
- 6. To delete timer programming, press the P + or – button until h œ:‹‹ is indicated on the digital display.
- 7. Close the door.
- End of programme
- The end of the programme O / ‹:‹‹ is displayed on the floor – provided the optical display is switched on and is visible.
- The end of the programme is also indicated by an acoustic signal. This function can be changed as follows:
- 2. Switch on ON/OFF switch (.
- 3. Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display.
- 4. Release both buttons.
- 5. Press programme button # until the factory set value ›:‹ƒ is indicated on the digital display h.
- 2. Press START button `, the set value is saved.
- 3. Close the door.
- Automatic switch off after end of programme or interior light*Automatic switch off / interior light
- * depending on model
- To save energy, the dishwasher can be automatically switched off 1 min or 120 min after the programme ends.
- The setting can be selected from ˜:‹‹ to ˜:‹ƒ.
- Appliance does not switch off automatically.
- The interior light 1" comes on when the door is opened irrespective of whether the ON/OFF switch ( is switched on or off. When the door is closed the light is off. If the door is open for longer than 60 min., the light switches off automatically. The...
- Appliance switches off after 1 min.
- Appliance switches off after 120 min.
- 2. Switch on ON/OFF switch (.
- 3. Hold down programme button # and press START button ` until •:‹... is indicated on the digital display.
- 4. Release both buttons.
- 5. Keep pressing programme button # until the value ˜:‹... is indicated on the numerical display h.
- 2. Press START button `.
- 3. Close the door.
- Switching off the appliance
- Interrupting the programme
- Terminating the programmeTerminating the programme (Reset)
- Changing the programme
- Intensive drying
- The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!)
- 2. Switch on ON/OFF switch (.
- 3. Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display.
- 4. Release both buttons.
- 5. Press programme button # until the factory set value š:‹‹ is indicated on the digital display h.
- 2. Press START button `.
- 3. Close the door.
- 2 Cleaning and maintenance
- Cleaning and maintenance
- A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems.
- Overall condition of the machine
- ■ Check spray arm for grease and limescale deposits.
- ■ Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature.
- ■ To extend the life of your appliance, clean the appliance regularly with a special dishwasher detergent.
- ■ To ensure that the door seal always remains clean and hygienic, regularly clean it with a damp cloth and a little washing-up liquid.
- ■ If the appliance is switched off for a prolonged period, leave the door ajar to prevent the formation of an unpleasant odour.
- Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage.
- Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces.
- Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time.
- Special salt and rinse aid
- Filters
- The filters 1Z keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters.
- The filter system consists of a coarse filter, a flat fine filter and a microfilter.
- 2. Unscrew filter cylinder as illustrated and take out filter system.
- 3. Remove any residue and clean filters under running water.
- 4. Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system.
- Spray arms
- 3 Fault, what to do?
- Fault, what to do?
- Experience has shown that you can rectify most faults which occur in daily operation yourself. This ensures that the machine is quickly available to you again. In the following overview you can find possible causes of malfunctions and helpful informa...
- Waste water pump
- Large food remnants or foreign objects which were not captured by the filters may block the waste water pump. The rinsing water will then be above the filter.
- In this case:
- 2. Take out top basket 12 and bottom basket 1b.
- 3. Remove the filters 1Z.
- 4. Scoop out water, use a sponge if required.
- 5. Prise out the white pump cover (as illustrated) using a spoon. Grip the cover on the crosspiece and lift diagonally inwards. Remove cover completely.
- 6. Check impeller wheel and remove any foreign objects.
- 7. Place cover in the original position and press down until it engages (click).
- 8. Install filters.
- 9. Re-insert baskets.
- Fault table
- Fault
- Reason
- Remedial action
- * depending on model
- 4 Customer service
- Customer service
- If you are unable to rectify the fault, please contact your customer service. We always find a suitable solution, even to avoid unnecessary visits by technicians. Contact information for your nearest customer service can be found on the back of these...
- Rely on the competence of the manufa cturer. Contact us. You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your domestic appliances.
- * depending on model
- 5 Installation and connection
- Installation and connection
- The dishwasher must be connected correctly, otherwise it will not function properly. The specifications for the inlet and outlet as well as the electrical connected loads must correspond with the required criteria as specified in the following paragr...
- Install the appliance in the correct sequence:
- 2. Installing the appliance
- 3. Waste water connection
- 4. Drinking water connection
- 5. Electrical connection
- Product package
- Safety instructions
- Delivery
- Technical specifications
- Weight:
- max. 45 kg
- Voltage:
- 220–240 V, 50 Hz or 60 Hz
- Connected load:
- 2.0–2.4 kW
- Fuse:
- 10/16 A (UK 13A)
- Power input:
- off mode (Po)* 0.10 W
- left on mode (Pl)* 0.10 W
- *according to regulations (EU) nos. 1016/2010 and 1059/2010
- Additional functions and settings may increase the power input.
- Water pressure:
- at least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar). At a higher water pressure: connect pressure-reducing valve ahead.
- Inlet rate:
- minimum 10 litres/minute
- Water temperature:
- cold water; hot water max. temperature 60 °C.
- Capacity:
- 9–10 place settings (depending on model).
- Installation
- The required installation dimensions can be found in the installation instructions. Level the appliance with the aid of the height-adjustable feet. Ensure that the appliance is situated securely on the floor.
- ■ A built-under or integrated appliance which is installed subsequently as a free-standing appliance must be secured to prevent it from overturning, e.g. by screwing it to the wall or by installing it under a continuous worktop which is screwed to ...
- ■ The appliance can easily be installed in a fitted kitchen between wooden and plastic walls.
- Waste-water connection
- Drinking water connection
- Warm water connection *Warm water connection
- * depending on model
- The dishwasher can be connected to cold or hot water up to max. 60 °C.
- Connection to hot water is recommended if the hot water can be supplied by energetically favourable means and from a suitable installation, e.g. solar heating system with circulation line.
- This will save energy and time.
- The hot water setting ‘:‹‚ allows you to adjust your appliance optimally to operation with hot water.
- It is recommended to have a water temperature (temperature of the incoming water) of at least 40 °C and no more than 60 °C.
- It is not recommended to connect the appliance to hot water if the water is supplied from an electric boiler.
- 2. Switch on ON/OFF switch (.
- 3. Hold down programme button # and press START button ` until •:‹... is indicated on the digital display.
- 4. Release both buttons.
- 5. Press programme button # until the factory set value ‘:‹‹ is indicated on the digital display h.
- 2. Press START button `.
- 3. Close the door.
- Electrical connection
- ■ Connect the appliance to an alternating current only, ranging from 220 V to 240 V and 50 Hz or 60 Hz via a correctly installed socket with protective earth conductor. See rating plate for required fusing 92.
- ■ The socket must be near the appliance and freely accessible following installation.
- ■ The connection may be modified by technicians only.
- ■ A power cord extension may be purchased from customer service only.
- ■ Use only a residual current operated circuit-breaker which features the symbol ‚. Only this extension guarantees compliance with the currently valid regulations.
- ■ The appliance features a water damage protection system. Please note the system will not function unless the power supply is connected.
- Removing the appliance
- Transportation
- Empty the dishwasher and secure loose parts.
- 2. Open the door.
- 3. Switch on ON/OFF switch (.
- 4. Select programme with the highest temperature.
- 5. Press START button `.
- 6. Close the door.
- 7. Open door after approx. 4 minutes.
- 8. Press START button ` until ‹:‹‚ is indicated on the digital display.
- 9. Close the door.
- 10. Open door after approx. 1 minute.
- 11. Switch off ON/OFF switch (.
- 12. Turn off the tap, disconnect supply hose and drain water.
- Protection against frostProtection against frost (Emptying the appliance)
en Intended use
4
End of programme . . . . . . . . . . . . . . 24
Automatic switch off / interior light . . 25
Switching off the appliance. . . . . . . . 25
Interrupting the programme . . . . . . . 26
Terminating the programme . . . . . . . 26
Changing the programme. . . . . . . . . 26
Intensive drying. . . . . . . . . . . . . . . . . 26
2 Cleaning and maintenance . . . 27
Overall condition of the machine . . . 27
Special salt and rinse aid . . . . . . . . . 27
Filters . . . . . . . . . . . . . . . . . . . . . . . . 28
Spray arms . . . . . . . . . . . . . . . . . . . . 28
3 Fault, what to do? . . . . . . . . . . 29
Waste water pump . . . . . . . . . . . . . . 29
Fault table. . . . . . . . . . . . . . . . . . . . . 30
4 Customer service . . . . . . . . . . 39
5 Installation and connection . . 39
Product package . . . . . . . . . . . . . . . 39
Safety instructions. . . . . . . . . . . . . . . 39
Delivery. . . . . . . . . . . . . . . . . . . . . . . 40
Technical specifications . . . . . . . . . . 40
Installation. . . . . . . . . . . . . . . . . . . . . 40
Waste-water connection . . . . . . . . . . 40
Drinking water connection . . . . . . . . 41
Warm water connection . . . . . . . . . . 41
Electrical connection. . . . . . . . . . . . . 41
Removing the appliance . . . . . . . . . . 42
Transportation. . . . . . . . . . . . . . . . . . 42
Protection against frost
(Emptying the appliance) . . . . . . . . . 42
8 Intended use
Intended use
This appliance is intended for
use in the home and
domestic environments.
Use the dishwasher only in
the home and only for its
designated purpose: for
washing domestic dishes.
This appliance is intended for
use up to a maximum altitude
of 4000 metres above sea
level.