HOB [en] INSTRUCTION MANUAL T5..T6...
: : : : ,(& 2 Ø = cm
en Table of contents [ en] I NSTRUCTI ON MANUAL 8 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ( Important safety information . . . . . . . . . . . . . . . 5 ] Causes of damage . . . . . . . . . . . . . . . . . . . . . . . . 6 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 7 Environmental protection . . . . . . . . . . . . . . . . . . 7 Energy-saving advice . . . . . . . . . . . . . . . . . . . . . . . . . .
en Intended use 8Intended use Read these instructions carefully. Please keep the instruction and installation manual, as well as the appliance certificate, in a safe place for later use or for subsequent owners. Check the appliance after removing it from the packaging. If it has suffered any damage in transport, do not connect the appliance, contact the Technical Assistance Service and provide written notification of the damage caused, otherwise you will lose your right to any type of compensation.
Important safety information (Important safety information I mpor t ant saf et y i nf or mat i on :Warning – Risk of fire! Hot oil and fat can ignite very quickly. Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar. Risk of fire! ■ The hotplates become very hot. Never place combustible items on the hob. Never place objects on the hob.
en Causes of damage ]Causes of damage Caution! Rough pan bases may scratch the hob. ■ Avoid leaving empty pots and pans on the hotplate. Doing so may cause damage. ■ Do not place hot pans on the control panel, the indicator area, or the hob frame. Doing so may cause damage. ■ Hard or pointed objects dropped on the hob may damage it. ■ Aluminium foil and plastic containers will melt if placed on the hotplate while it is hot. The use of laminated sheeting is not recommended on the hob.
Environmental protection 7Environmental protection In this section, you can find information about saving energy and disposing of the appliance. Envi r onment al pr ot ect i on Energy-saving advice ■ ■ ■ ■ ■ ■ Always use the correct lid for each pan. Cooking without a lid uses a lot more energy. Use a glass lid to provide visibility and avoid having to lift the lid. Use pans with flat bases. Bases that are not flat use a lot more energy.
en Induction cooking Some induction cookware does not have a fully ferromagnetic base: ■ ■ If the base of the cookware is only partially ferromagnetic, only the area that is ferromagnetic will heat up. This may mean that heat will not be distributed evenly. The non-ferromagnetic area may not heat up to a sufficient temperature for cooking. The ferromagnetic area will also be reduced if the material from which the base of the cookware is made contains aluminium, for example.
Getting to know your appliance en *Getting to know your appliance You can find information on the dimensions and power of the hotplates in~ Page 2 Get i ng t o know your ap l i ance Note: . Depending on the appliance model, individual details and colours may differ. The control panel Indicators Controls # – ˜ { | œ x .
en Twist-Pad with Twist knob Residual heat indicator The hob has a residual heat indicator for each hotplate. This indicates that a hotplate is still hot. Do not touch a hotplate while the residual heat indicator is lit up. The following indicators are shown depending on the amount of residual heat: ■ ■ Display •: High temperature Display œ: Low temperature jTwist-Pad with Twist knob The twistpad is the area in which you can use the twist knob to select the hotplates and heat settings.
Operating the appliance Operating the hob without the twist knob The hob can also be operated without the twist knob: 1. Switch on the hob using the main switch. 2. Within the next 5 seconds, simultaneously touch and hold the œ and . symbols for 4 seconds. An audible signal will sound. 3. Touch the . symbol repeatedly until the indicator for the required hotplate lights up. 4. Then set the required heat setting using the œ or x symbol. The hotplate has now been activated.
en Operating the appliance Changing the heat setting Select the hotplate and change the heat setting using the twist knob. Chef's recommendations Switching off the hotplate ■ Select the hotplate and turn the twist knob until ‹ appears. The hotplate switches itself off and the residual heat indicator lights up. Notes ■ If no pan has been placed on the hotplate, the selected power level flashes. After a certain time has elapsed, the hotplate switches off.
Operating the appliance en Heat setting Cooking time (mins) Boiling, steaming, braising Rice (with double the volume of water) Rice pudding*** Unpeeled boiled potatoes Boiled potatoes Pasta, noodles* Stew Soups Vegetables Vegetables, frozen Cooking in a pressure cooker 2. - 3. 2-3 4. - 5. 4. - 5. 6-7 3. - 4. 3. - 4. 2. - 3. 3. - 4. 4. - 5.
en Flex Zone As two independent hotplates |Flex Zone You can use each flex zone as a single hotplate or as two independent hotplates, as required. It consists of four inductors that work independently of each other. If using the flexible cooking zone, only the area that is covered by cookware is activated. The flexible cooking zone is used like two independent hotplates.
Move function uMove function This function activates the entire flexible cooking zone, which is divided into three cooking areas and which has preset heat settings. Only use one item of cookware. The size of the cooking area depends on the cookware used and whether it is positioned correctly. Move f unct i on Cooking areas en Activation 1. Select one of the two hotplates in the flexible cooking zone. | symbol. The indicator beside the | symbol lights up.
en Time-setting options OTime-setting options Changing or deleting the time Your hob has three timer functions: Change the cooking time using the twist knob or on the control panel or set ‹‹ to delete the programmed cooking time. Ti me- set i ng opt i ons ■ ■ ■ Programming the cooking time Kitchen timer Stopwatch function Programming the cooking time The hotplate automatically switches off after the time that is set has elapsed. Setting procedure: 1.
PowerBoost function Stopwatch function The stopwatch function displays the time that has elapsed since activation. This functions independently from the hotplates and from other settings. This function does not automatically switch off a hotplate. Activating Touch the œ symbol. The ‹‹ symbol and the b indicator light up in the timer display. The time begins to elapse. en vPowerBoost function The PowerBoost function enables you to heat up large quantities of water faster than when using heat setting Š.
en ShortBoost function xShortBoost function The ShortBoost function enables you to heat cookware faster than when using heat setting Š. Shor t Bo st f unct i on After deactivating the function, select the appropriate heat setting for your food. This function can always be activated for a hotplate, provided the other hotplate in the same group is not in use (see illustration).
Childproof lock en AChildproof lock kWipe protection You can use the childproof lock to prevent children from switching on the hob. Wiping over the control panel while the hob is switched on may alter the settings. To avoid doing this, you can use the hob's "Lock control panel for cleaning" function. To activate this function: Remove the twist knob. The z indicator will be lit.The control panel will remain locked for 35 seconds.
en Basic settings QBasic settings The appliance has various basic settings. These basic settings can be altered to suit your individual requirements. Basi c set i ngs Indicator/ symbol Function ™‚ Childproof lock ‹ ‚ ƒ ™ƒ Signal tones ‹ ‚ ƒ „ ™„ Confirmation and fault signals are switched off. Only the fault signal is switched on. Only the confirmation signal is switched on. All signal tones are switched on.* Display energy consumption ‹ ‚ ™† Manual*. Automatic. Function deactivated.
Basic settings ™‚ƒ Check the cookware and the cooking results ‹ ‚ ƒ ™‹ en Not suitable Not perfect Suitable Restore to standard settings ‹ ‚ Individual settings.* Restore factory settings. *Factory setting **The hob's maximum power output is shown on the rating plate. -------- To access the basic settings: 6. Touch the The hob must be off. The settings have been saved. 1. Switch on the hob. 2. Within ten seconds, touch and hold the .
en Energy consumption indicator [Energy consumption indicator This function indicates the total amount of energy consumed by this hob the last time it was used for cooking. Once the hob is switched off, the energy consumption is displayed in kilowatt hours (e.g. ‚.‹‰ kWh) for 10 seconds. The accuracy of the information displayed depends on the voltage quality of the mains power supply, among other factors.
Power manager en hPower manager DCleaning You can use the power manager to set the total power of the hob. The hob is preset at the factory. Its maximum performance is specified on the rating plate. You can use the power manager to change the value in accordance with the requirements for the relevant electrical installation. In order not to exceed this set value, the hob automatically distributes the power available between the cooking zones that are switched on.
en Frequently Asked Questions (FAQ) {Frequently Asked Questions (FAQ) Fr equent l y Asked Quest i ons ( FAQ) Using the appliance Why can't I switch on the hob and why is the childproof lock symbol lit? The childproof lock is activated. You can find information on this function in the section on ~ "Childproof lock" Why are the displays flashing and why can I hear an audible signal? Remove any liquid or food remains from the control panel. Remove any objects from the control panel.
Trouble shooting en Cleaning How do I clean the hob? Using a special glass-ceramic cleaning agent produces the best results. We advise against using harsh or abrasive cleaning agents, dishwater detergent (concentrated) or scouring pads. You can find more information on cleaning and caring for your hob in the section on ~ "Cleaning" 3Trouble shooting Usually, faults are small matters that are easy to eliminate. Please read the information in the table before calling the after-sales service.
en Customer service Notes ■ If “ appears on the display, press and hold the twist knob next to the mark for the relevant cooking zone in order to read the fault code. ■ If the fault code is not listed in the table, disconnect the hob from the mains power supply and wait 30 seconds before reconnecting it. If this code is displayed again, contact the technical after-sales service and specify which fault code has appeared. ■ If a fault occurs, the appliance will not switch to standby mode.
Test dishes en ETest dishes This table has been produced for test institutes to facilitate the testing of our appliances. The data in the table refer to our Schulte-Ufer cookware accessories (4-piece cooking set for induction hob Z9442X0) with the following dimensions: Test di shes ■ ■ ■ ■ Saucepan: 16 cm Ø, 1.2 l for 14.5 cm Ø hotplates Pot: 16 cm Ø, 1.7 l for 14.5 cm Ø hotplates Pot: 22 cm Ø, 4.
en Test dishes Test dishes Cooking rice pudding Rice pudding, cooked with the lid on Temperature of the milk: 7 ºC Heat the milk until it starts to rise up. Set the recommended heat setting and add rice, sugar and salt to the milk. The cooking time, including preheating, is approx. 45 minutes. Ingredients: 190 g short-grain rice, 90 g sugar, 750 ml milk (3.5% fat content) and 1 g salt Ingredients: 250 g short-grain rice, 120 g sugar, 1 l milk (3.5% fat content) and 1.
Valid within Great Britain: Imported to Great Britain by BSH Home Appliances Ltd.
