T59.S5...
: : : : : : : : : : ,(& 2 Ø = cm
en Table of contents [ en] I NSTRUCTI ON MANUAL 8 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ( Important safety information . . . . . . . . . . . . . . . 5 ] Causes of damage . . . . . . . . . . . . . . . . . . . . . . . . 6 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 7 Environmental protection . . . . . . . . . . . . . . . . . . 7 Energy-saving advice . . . . . . . . . . . . . . . . . . . . . . . . . .
en Intended use 8Intended use Read these instructions carefully. Please keep the instruction and installation manual, as well as the appliance certificate, in a safe place for later use or for subsequent owners. Check the appliance after removing it from the packaging. If it has suffered any damage in transport, do not connect the appliance, contact the Technical Assistance Service and provide written notification of the damage caused, otherwise you will lose your right to any type of compensation.
Important safety information (Important safety information I mpor t ant saf et y i nf or mat i on :Warning – Risk of fire! Hot oil and fat can ignite very quickly. Never leave hot fat or oil unattended. Never use water to put out burning oil or fat. Switch off the hotplate. Extinguish flames carefully using a lid, fire blanket or something similar. Risk of fire! ■ The hotplates become very hot. Never place combustible items on the hob. Never place objects on the hob.
en Causes of damage ]Causes of damage Caution! Rough pan bases may scratch the hob. ■ Avoid leaving empty pots and pans on the hotplate. Doing so may cause damage. ■ Do not place hot pans on the control panel, the indicator area, or the hob frame. Doing so may cause damage. ■ Hard or pointed objects dropped on the hob may damage it. ■ Aluminium foil and plastic containers will melt if placed on the hotplate while it is hot. The use of laminated sheeting is not recommended on the hob.
Environmental protection 7Environmental protection In this section, you can find information about saving energy and disposing of the appliance. Envi r onment al pr ot ect i on Energy-saving advice ■ ■ ■ ■ ■ ■ Always use the correct lid for each pan. Cooking without a lid uses a lot more energy. Use a glass lid to provide visibility and avoid having to lift the lid. Use pans with flat bases. Bases that are not flat use a lot more energy.
en Induction cooking Some induction cookware does not have a fully ferromagnetic base: ■ ■ If the base of the cookware is only partially ferromagnetic, only the area that is ferromagnetic will heat up. This may mean that heat will not be distributed evenly. The non-ferromagnetic area may not heat up to a sufficient temperature for cooking. The ferromagnetic area will also be reduced if the material from which the base of the cookware is made contains aluminium, for example.
Getting to know your appliance en *Getting to know your appliance You can find information on the dimensions and power of the hotplates in~ Page 2 Get i ng t o know your ap l i ance The control panel Touch controls Main switch # – ˜ Û { | œ x .
en Getting to know your appliance The hotplates Hotplates Simple hotplate Û/ Use cookware that is a suitable size $ ò Triple-circuit hotplate The hotplate switches on automatically when you use cookware with a base that covers the outer edge of the zone (ð or ò). á Flexible cooking zone See section on ~ "Flex Zone" Only use cookware that is suitable for induction cooking; see the section on ~ "Induction cooking". Residual heat indicator The hob has a residual heat indicator for each hotplate.
Twist-Pad with Twist knob en jTwist-Pad with Twist knob Operating the hob without the twist knob The twistpad is the area in which you can use the twist knob to select the hotplates and heat settings. The twist knob automatically centres itself in the twistpad area. The twist knob is magnetic and is placed on top of the twistpad. To activate a hotplate, touch the twist knob at the level for the required hotplate. Turning the twist knob selects the heat setting. 1.
en Operating the appliance 1Operating the appliance This chapter explains how to set a hotplate. The table shows heat settings and cooking times for various meals. Changing the heat setting Select the hotplate and change the heat setting using the twist knob. Oper at i ng t he ap l i ance Switching the hob on and off Switch the hob on and off using the main switch. To switch on: Touch the # symbol. The symbols for the hotplates and the functions available at this time light up.
Operating the appliance en Cooking table The table shows which heat setting is suitable for each type of food. The cooking time may vary depending on the type, weight, thickness and quality of the food. Heat setting Cooking time (mins) Melting Chocolate coating Butter, honey, gelatine 1 - 1. 1-2 - Heating and keeping warm Stew, e.g. lentil stew Milk* Heating sausages in water* 1. - 2 1. - 2.
en Operating the appliance Roasting/frying with little oil* Escalope, plain or breaded Escalope, frozen Chop, plain or breaded** Steak (3 cm thick) Poultry breast (2 cm thick)** Poultry breast, frozen** Rissoles (3 cm thick)** Hamburgers (2 cm thick)** Fish and fish fillet, plain Fish and fish fillet, breaded Fish, breaded and frozen, e.g. fish fingers Scampi, prawns Sautéeing fresh vegetables and mushrooms Stir-fry, vegetables, meat cut in Asian-style strips Frozen dishes, e.g.
Flex Zone |Flex Zone You can use each flex zone as a single hotplate or as two independent hotplates, as required. It consists of four inductors that work independently of each other. If using the flexible cooking zone, only the area that is covered by cookware is activated. en As two independent hotplates The flexible cooking zone is used like two independent hotplates.
en Move function uMove function This function activates the entire flexible cooking zone, which is divided into three cooking areas and which has preset heat settings. Only use one item of cookware. The size of the cooking area depends on the cookware used and whether it is positioned correctly. Move f unct i on Cooking areas Activation 1. Select one of the two hotplates in the flexible cooking zone. | symbol. The indicator beside the | symbol lights up.
Time-setting options OTime-setting options Ti me- set i ng opt i ons Your hob has three timer functions: ■ ■ ■ Programming the cooking time Kitchen timer Stopwatch function Programming the cooking time The hotplate automatically switches off after the time that is set has elapsed. Setting procedure: 1. Select the hotplate and the required heat setting. 2. Touch the x symbol. The x display for the hotplate lights up. ‹‹ lights up on the timer display.
en PowerBoost function Stopwatch function The stopwatch function displays the time that has elapsed since activation. This functions independently from the hotplates and from other settings. This function does not automatically switch off a hotplate. Activating Touch the œ symbol. The ‹‹ symbol and the b indicator light up in the timer display. The time begins to elapse. vPowerBoost function The PowerBoost function enables you to heat up large quantities of water faster than when using heat setting Š.
ShortBoost function en xShortBoost function zKeep warm function The ShortBoost function enables you to heat cookware faster than when using heat setting Š. This function is suitable for melting chocolate or butter and for keeping food warm. Shor t Bo st f unct i on After deactivating the function, select the appropriate heat setting for your food. This function can always be activated for a hotplate, provided the other hotplate in the same group is not in use (see illustration).
en Frying Sensor cFrying Sensor This function can be used to fry food while maintaining the suitable frying pan temperature. The cooking zones that have this function are identified by the roasting function symbol. Fr yi ng Sensor Advantages when frying ■ ■ The hotplate only heats up if this is required to maintain the temperature. This saves energy and prevents the oil or fat from overheating.
Frying Sensor en Temperature settings Temperature setting 1 Very low 2 Low 3 Medium - low 4 Medium - high 5 High Suitable for Preparing and reducing sauces, sweating vegetables and frying food in extra virgin olive oil, butter or margarine. Frying food using extra virgin olive oil, butter or margarine, e.g. omelettes. Frying fish and Thick food, e.g. meatballs and sausages. Frying steaks, medium or well-done, frozen, breaded and fine foods, e.g. escalope, fresh ragout and vegetables.
en Frying Sensor Temperature Total frying time after the signal setting sounds (mins.) Potatoes Fried potatoes (boiled in their skin) Fried potatoes (made from raw potatoes) Potato pancakes** Swiss rösti Glazed potatoes 5 4 5 2 3 6 - 12 15 - 25 2,5 - 3,5 50 - 55 15 - 20 Vegetables Garlic, onions Courgettes, aubergines Peppers, green asparagus Vegetables sautéed in oil, e.g.
Childproof lock Setting procedure Select the appropriate temperature setting from the table. Place the empty frying pan on the hotplate. en AChildproof lock You can use the childproof lock to prevent children from switching on the hob. Chi l dpr o f l ock 1. Select the hotplate and touch the lights up in the hotplate display. Û symbol. Û Activating and deactivating the childproof lock The hob must be switched off. To activate: Touch the . symbol for approx. 4 seconds.
en Wipe protection kWipe protection Wiping over the control panel while the hob is switched on may alter the settings. To avoid doing this, you can use the hob's "Lock control panel for cleaning" function. To activate this function: Remove the twist knob. The z indicator will be lit.The control panel will remain locked for 35 seconds. You will now be able to clean the surface of the control panel without altering the settings.
Basic settings en QBasic settings The appliance has various basic settings. You can adapt these to suit your cooking habits. Basi c set i ngs Display Function ™‚ Automatic childproof lock ‹ ‚ ƒ ™ƒ Audible signals ‹ ‚ ƒ „ ™„ Confirmation and fault signals are switched off. Only the fault signal is switched on. Only the confirmation signal is switched on. All signal tones are switched on.* Display energy consumption ‹ ‚ ™† Manual*. Automatic. Function deactivated. Switched off.* Switched on.
Basic settings en Display Function ™‹ Restoring the factory settings ‹ ‚ Individual settings.* Restore factory settings. * Factory settings To access the basic settings: 6. Touch the The hob must be off. The settings have been saved. 1. Switch on the hob. 2. Within ten seconds, touch and hold the . symbol for Leaving the basic settings Turn off the hob with the main switch. approximately three seconds. The first four displays provide product information.
Energy consumption indicator [Energy consumption indicator This function indicates the total amount of energy consumed by this hob the last time it was used for cooking. Once switched off, the energy consumption in kWh is displayed for 10 seconds. The picture shows an example with an energy consumption of ‚.‹‰ kWh. Ener gy consumpt i on i ndi cat or en tCookware check This function can be used to check the speed and quality of the cooking process depending on the cookware.
en Home Connect oHome Connect Note: Home Connect is due to be introduced for NEFF from the end of 2018. Home Con ect This appliance is WLAN-enabled and settings can be sent to the appliance via a mobile device. If the appliance is not connected to the home network, the appliance functions in the same way as a hob with no network connection. The hob can always be operated via the control panel.
Home Connect Manual registration in the home network 1. Touch the . symbol for 3 seconds. Product information will be displayed. 2. Touch the U symbol repeatedly until the •’‚ setting appears. ‹ lights up in the cooking position display. 3. Set the value to ƒ using the twist knob. ƒ and the D symbol will flash on the cooking position display. en The hob is connected to the home network if the D symbol no longer flashes but is lit up on the cooking position display.
en Home Connect Symbol Function •’‡ ‹ ‚ Remote access by Customer Service •’ˆ ‹ ‚ ƒ „ WLAN signal strength •’‰ ‹ ‚ Connection to Home Connect server Not permitted. Permitted. Not connected to home network (WLAN). Signal strength 1 (poor) Signal strength 2 (moderate) Signal strength 3 (good) Not connected. Connected. * Basic setting Notes ■ The •’ƒ setting is only displayed if the appliance is connected to the home network.
Home Connect 1. Touch the . symbol for 3 seconds. Product information will be displayed. 2. Touch the U symbol repeatedly until the •’ƒ setting appears. ‹ lights up in the cooking position display. 3. Set the value to ‚ using the twist knob. 4. Follow the instructions in the app to complete the connection process. Settings via app Using the Home Connect app, you can easily access the basic settings for your hob and send settings for the cooking positions to the hob.
en Hood connection eHood connection You can connect this appliance to a suitable extractor hood and control the functions of the hood via your hob. There are various options for connecting the appliances together: Home Connect Two appliances can be connected using the Home Connect app provided that both of them are Home Connect-compatible. Observe the supplied Home Connect documents for this.
Hood connection The connection process has been completed once the „ value appears on the cooking position display.The symbols for the hood controls on the hob are displayed on the hob's control panel. Note: The connection can only be established when both appliances are connected to your home network and are engaged in connection. If the connection process has already timed out for one of the two appliances, try to connect again (basic settings, ™‚‡ setting).
Cleaning en DCleaning Suitable maintenance and cleaning products can be purchased from the after-sales service or in our e-Shop. Cl eani ng Hob Cleaning Always clean the hob after cooking. This will prevent food deposits from becoming burned on. Only clean the hob after the residual heat indicator has gone out. Clean the hob with a damp dish cloth and dry it with a cloth or towel to prevent limescale build-up. Only use cleaning agents that are suitable for this type of hob.
Frequently Asked Questions (FAQ) en {Frequently Asked Questions (FAQ) Fr equent l y Asked Quest i ons ( FAQ) Using the appliance Why can't I switch on the hob and why is the childproof lock symbol lit? The childproof lock is activated. You can find information on this function in the section on ~ "Childproof lock" Why are the displays flashing and why can I hear an audible signal? Remove any liquid or food remains from the control panel. Remove any objects from the control panel.
en Trouble shooting Cookware How do you switch on the dual-circuit and triple-circuit hotplates? These hotplates can detect cookware of different sizes. Depending on the material and the properties of the cookware, the hotplate automatically activates the single-, dual- or triple-circuit hotplate in order for the appropriate heat output to be supplied to achieve good cooking results.
Customer service Notes ■ If “ appears on the display, the Twist knob for the burner in question must be held down in order to be able to read off the fault code. ■ If the fault code is not listed in the table, disconnect the hob from the power supply and wait 30 seconds before reconnecting it. If the display appears again, contact technical Customer Service and tell them the precise fault code.If the display appears again, contact technical after-sales and tell them the precise fault code.
en Test dishes ETest dishes This table has been produced for test institutes to facilitate the testing of our appliances. The data in the table refer to our Schulte-Ufer cookware accessories (4-piece cooking set for induction hob Z9442X0) with the following dimensions: Test di shes ■ ■ ■ ■ Saucepan: 16 cm Ø, 1.2 l for 14.5 cm Ø hotplates Pot: 16 cm Ø, 1.7 l for 14.5 cm Ø hotplates Pot: 22 cm Ø, 4.
Test dishes Test dishes Preheating Heat set- Cooking time Cookware Lid ting (min:sec) Cooking rice pudding Rice pudding, cooked with the lid on Temperature of the milk: 7 ºC Heat the milk until it starts to rise up. Set the recommended heat setting and add rice, sugar and salt to the milk. The cooking time, including preheating, is approx. 45 minutes. Ingredients: 190 g short-grain rice, 90 g sugar, 750 ml milk (3.
&RQVWUXFWD 1HII 9HUWULHEV *PE+ &DUO :HU\ 6WUDH ' 0QFKHQ 5HJLVWHU \RXU SURGXFW RQOLQH ZZZ QHII LQWHUQDWLRQDO FRP *9001294663* 9001294663 970616(10) en
