User's Manual

2120
3
2
1
3
2
1
2. Twist Nest Protect counterclockwise until
it disconnects from the backplate.
3. Detach the power connector
from the back of Nest Protect
and open the battery door.
4. Replace the batteries.
Align the + positive and
- negative ends with the
markings in the battery
compartment.
5. Close the battery compartment.
Do not force the door closed.
6. Reattach the power connector.
7. Push Nest Protect onto the backplate and
turn it clockwise until you feel it grip.
8. Turn power to Nest Protect back on at the
breaker box.
9. Press the Nest button twice.
SERVICING
1. Before sending Nest Protect for service,
visit nest.com/support
2. If your Nest Protect needs servicing,
first contact our support team to get
a returnnumber
3. Send your Nest Protect to:
Nest Labs
(YOUR RETURN NUMBER)
4 East Stow Road
Marlton, NJ 08053 USA
GENERAL MAINTENANCE
CLEANING YOUR NEST PROTECT
Nest Protect has been designed to be as
maintenance free as possible, but you should
keep it clean. As with any smoke alarm,
dust buildup on the outside or inside of Nest
Protect can stop it from working properly.
To clean Nest Protect:
1. Turn off power to Nest Protect at the
breaker box (see p.9)
2. Remove it from the wall or the ceiling (turn
counterclockwise until it comes off the
backplate and detach the power connector).
3. Wipe the outside with a clean, slightly
damp cloth. Don’t use any soaps or solvents.
4. Place Nest Protect on a soft, dry cloth with
the Nest button facing down. Open the
battery compartment door and remove the
batteries. Remove the screws and lift off
the back. Be careful to not lose the screws.
5. Gently vacuum the inside. Make sure
to clean all the way around the mesh
sides of the smoke chamber (the large
metal circle).
Note: Never use detergents or solvents (like
glass cleaner) on your Nest Protect and do
not spray air fresheners, hair spray or other
aerosols near it. Do not get water inside the
alarm or paint over it.
REPLACING THE BACKUP BATTERIES
In case of a power outage, Nest Protect will
use three AA Energizer® Ultimate Lithium
batteries (L91) for backup. These batteries
can be purchased at your local retailer.
1. Turn off power to Nest Protect at the
breaker box (see p.9)
WARNING
• Use only batteries specified by Nest.
Use of a different battery model will
have a detrimental effect on the smoke
alarm operation.
• Never disconnect a wired alarm to stop
an unwanted alarm (caused by cooking
smoke, etc.) Removing power disables the
alarm so it cannot sense smoke or carbon
monoxide (CO). Instead open a window or
fan the smoke away from the unit.
• The batteries cannot work until you install
the batteries in the correct position
(Match + to + and - to -).
• Once Nest Protect has expired you’ll no
longer be protected from smoke or CO if
you don’t replace it.
GENERAL MAINTENANCE
YELLOW pulses. Low battery. Change the batteries
of Nest Protect now.
“THE BATTERY IS LOW IN
THE [ROOM NAME].
REPLACE THE BATTERY
NOW.” Single chirp
every 60 seconds.
Nest Protect has tested
its sensors and there is
a problem.
Clean according to
instructions on page 20.
If the problem persists,
replace Nest Protect.
“THE SENSORS HAVE
FAILED IN THE [ROOM
NAME]. REPLACE NEST
PROTECT NOW.” Single
chirp every 60 seconds.
Nest Protect has expired
and reached the end of
its life.
Replace Nest Protect now.
“NEST PROTECT HAS
EXPIRED. REPLACE IT
NOW.” Two chirps every
60 seconds.
There’s a problem with
the horn of Nest Protect.
Replace Nest Protect now.
“NEST PROTECT CAN’T
SOUND THE ALARM IN
THE [ROOM NAME].”Two
chirps every 60 seconds.
YELLOW pulses. Change the batteries
of Nest Protect soon.
Low battery.
“THE BATTERY IS LOW IN
THE [ROOM NAME].
REPLACE THE BATTERY
SOON.”
YELLOW pulses.
YELLOW pulses.
WHAT YOU HEAR WHAT IT MEANS WHAT TO DOWHAT YOU SEE
GENERAL MAINTENANCE
YELLOW pulses.