Learning Thermostat Installation Guide
Compatibility Nest works with over 95% of 24V heating and cooling systems, including gas, electric, oil, solar, hot water, geothermal, forced air, heat pump and radiant. It can control: • Heating: one, two and three stages (W1, W2, W3) • Cooling: one and two stages (Y1, Y2) • Heat pump: with auxiliary and emergency heat (O/B, AUX, E) • Fan (G) • Power (C, Rh, Rc) • Humidifier or dehumidifier (HUM, DEHUM) * Nest’s connector can accept only one of these wires: W3, E, HUM or DEHUM.
Contents Display Base Nest Screwdriver Wall Screws Optional Trim Plate Optional Steel Plate Optional Steel Plate Screws
1. Switch off power 2. Remove cover This protects you and avoids blowing a fuse. Adjust the temperature on your old thermostat to make sure your system is off. Some covers pop off, while others need to be unscrewed. Breaker Box Switch 3. Check your system 4. Remove any jumper wires If your old thermostat is labeled 120V or 240V or has thick wires with wire nuts, your system is high voltage. Not sure? Contact support. Jumper wires are short wires between two connectors. Nest doesn’t need them.
. Label wires Peel off the blue labels and attach them to your wires. Use the white labels if you have a E, W3, HUM or DEHUM wire. You can connect only one of these wires to Nest’s * connector. HUM and DEHUM wires may require a professional. Check at nest.com/works Tip: Take a picture of the wires on your old thermostat to help you remember. 6. Disconnect wires and remove base Tip: Wrap the wires around a pencil to keep them from falling into the wall. 7.
Optional in most homes Use trim plate if needed You can cover up holes or marks left by your old thermostat with the optional trim plate. Place the trim plate on the wall and put the base on top so they snap together, then screw them both to the wall. The trim plate can be found in the bottom of the Nest box. Optional in most homes Mounting Nest on an electrical box Electrical boxes aren’t common, but if you have one, secure the steel plate to the electrical box with two of the short steel plate screws.
8. Attach base 9. Connect wires After all the wires are connected, make sure they’re flush with the wall. 3/8” The exposed wire should be straight. 10. Attach display 11. Switch power back on Press the display until it clicks into place.
12. Setup and Nest Account Nest will turn on and walk you through setup. Turn the ring and press to select. Connect Nest to Wi-Fi during setup, then visit nest.com/account to create a Nest Account so you can control Nest from anywhere. For more information visit nest.com or call 855-4MY-NEST (855-469-6378). Recycle your old thermostat: see nest.com/responsibility Please recycle Nest’s 100% recyclable packaging.
IG-002-081512-US Learning Thermostat Guía de instalación
Compatibilidad Nest funciona con más del 95% de los sistemas de enfriamiento y calefacción de 24 V, que incluyen gas, electricidad, aceite, solar, agua caliente, geotérmicos, aire forzado, bomba de calor y radiante.
Contenido Pantalla Base Tornillos de pared Placa de molde opcional Placa de acero opcional Tornillos de la placa de acero opcional
1. Apaga la alimentación 2. Retira la cubierta Esto te protege y evita que el fusible explote. Ajusta la temperatura de tu viejo termostato para asegurarte de que el sistema esté apagado. Algunas cubiertas se salen solas, mientras que otras deben destornillarse. Disyuntor Interruptor 3. Verifica tu sistema 4. Retira los cables de puente Si tu viejo termostato está etiquetado como 120 V o 240 V o tiene cables gruesos con tuercas, tu sistema es de alto voltaje.
5. Etiqueta los cables Pela las etiquetas azules y conéctalas a los cables. Utiliza las etiquetas blancas si tienes un cable E, W3, HUM o DEHUM. Solo puedes conectar uno de los siguientes cables al conector estrella de Nest*. Los cables HUM y DEHUM pueden requerir un profesional. Visita nest.com/compatibilidad Consulte las instrucciones en inglés para ver los adhesivos de las etiquetas. 6.
Opcional en la mayoría de los hogares Utiliza la placa de molde si es necesario Puedes cubrir los orificios o marcas que dejó tu viejo termostato con la placa de molde opcional. Coloca la placa de molde en la pared y la base en la parte superior de manera que encajen en conjunto, luego atorníllalas en la pared. La placa de molde puede encontrarse en la parte inferior de la caja de Nest.
8. Conecta la base 9. Conecta los cables Después de conectar todos los cables, asegúrate de que estén al ras con la pared. 3/8” El cable expuesto debe estar derecho. 10. Conecta la pantalla Presiona la pantalla hasta que haga clic en su lugar. 11.
12. Ajustes y cuenta de Nest Nest se encenderá y te guiará en la configuración. Gira el anillo y presiona para seleccionar. Conecta Nest a Wi-Fi durante la configuracion, luego visita nest.com/cuenta para crear una cuenta de Nest y poder controlar Nest desde cualquier lugar. Para obtener más información, visita nest.com o llama al 855-4MY-NEST (855-469-6378). Recicla tu viejo termostato: visita nest.com/responsibilidad Recicle el material de embalaje 100% reciclable de Nest.