WF305556 Width-40inch Depth-17.5inch Height-33.7inch If you have any questions, please feel free to contact us. Email: service@aminalife.
! Safety and Care Advice Important – Please read these instructions fully before starting assembly • Check you have all the components and tools listed on the following pages. • During assembly do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups. • Assemble the item as close to its final position (in the same room) as possible.
Cam Bolt x 30 Cam lock x 30 8*30mm Dowel x 44 4*30mm Screw x 18 3*10mm Screw x 1 Iron sheet x 1 6*50mm Screw x 4 Vertical nut x 4 Magnetic collision x 1 3*14mm Screw x 2 Locking caster x 2 Caster x 3 4*14mm Screw x 20 6*30mm Dowel x 8 Shelf support pin x 4 3*12mm Screw x 2 T Hinge x 3 U press x 2 Y 3.
I II III P LU L PU OR Screwdrivers can be converted to Phillips and Slotted.
Using Camlocks Step 1 Connect the male camlock as diected in the assembly instructions using a scewdriver. 1 Step 2 DO NOT OVER TIGHTEN. NE PAS SERRER EXCESSIVEMENT. 2 Push the male camlock into the entry hole. 4 Step 3 Insert the female camlock as shown in the instruction. Note：ensure that the arrow on the top of the camlock points towards the entry hole for the male camlock. 3 Step 4 4 Turn the female camlock clockwise with a screwdriver.
2 14 15 1 14 12 21 6 5 20 11 12 4 10 13 9 19 3 7 23 19 18 8 16 22 18 17 19 19 27 27 26 28 26 25 24 28 25 24 5
Assembly Instructions R Step 1 R R CR A R 5 CR Cam Bolt x 1 350mm runner x 1 3.
Assembly Instructions R Step 3 R R R CR A R R A J A A I 180° R Magnetic collision x 1 Cam Bolt x 4 4 R CL 3*14mm Screw x 2 3.
Assembly Instructions Step 5 R R CL R A R A A A A A 3 A 3 A 180° A CL Cam Bolt x 9 3.
Assembly Instructions Step 7 C B C C B C C C 3 Cam lock x 3 B 8*30mm Dowel x 6 Step 8 9 22 R R 9 R 10 R 3.
Assembly Instructions Step 9 A A A 17 A 16 Cam Bolt x 4 Step 10 19 19 19 18 18 C C B B C C 16 Cam lock x 2 8*30mm Dowel x 4 10
Assembly Instructions Step 11 17 C C B C C B Cam lock x 2 8*30mm Dowel x 4 Step 12 C B 17 C B B B 16 Cam lock x 6 8*30mm Dowel x 4 3 C B C B 11
Assembly Instructions Step 13 C C C C D C C C D D C 8 D D C D C D D D 8*30mm Dowel x 10 4*30mm Screw x 8 Step 14 3 4 12 5 12 12
Assembly Instructions Step 15 A A A A A A A A Cam Bolt x 8 Step 16 C B B B B C B C B B C C B C C C C C Cam lock x 8 8*30mm Dowel x 10 13
Assembly Instructions Step 17 D D D 4*30mm Screw x 2 Step 18 L M 8 L L K M M M L M K M Locking caster x 2 Caster x 3 4*14mm Screw x 20 14
Assembly Instructions Step 19 R 2 Q R Q R Q Colloidal particles x 3 3.5*12mm Screw x 9 Step 20 R Q 2 R Q R Q R 3.
Assembly Instructions Step 21 R R S R 21 U S R S S 20 U U 3.5*12mm Screw x 8 Hinge x 4 press x 2 Step 22 20 R R 21 3.
Assembly Instructions Step 23 2 17
Assembly Instructions R Step 24 R S E R R F S 23 W V Iron sheet x 1 3*10mm Screw x 1 V 3.5*12mm Screw x 4 E Hinge x 2 W Hold hands x 1 4*16mm Screw x 1 Step 25 R 23 R 3.
Assembly Instructions Step 26 O O O O 13 Shelf support pin x 4 Step 27 D D A W A 26 27 24 V x2 D Cam Bolt x 4 x2 D 25 D V 4*30mm Screw x 8 Hold hands x 2 W 4*16mm Screw x 2 19
Assembly Instructions Step 28 27 B 26 26 N 25 28 25 N N x2 N Cam lock x 4 T T 24 B N T 6*30mm Dowel x 8 Hole to stick x 4 R Step 29 DL R R DR R 24 26 3.
Assembly Instructions Step 30 Step 31 P P X X Row and insert x 1 P 3*12mm Screw x 2 21
Assembly Instructions Step 32 T T T T T T Hole to stick x 12 Step 33 22
