Installation Guide for Fiber Taps 800-0146-001 CPUBTPLCSLMU Rev.
Fiber Tap Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Key Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 About This Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fiber Tap PLEASE READ THESE LEGAL NOTICES CAREFULLY. By using a Net Optics Tap you agree to the terms and conditions of usage set forth by Net Optics, Inc. No licenses, express or implied, are granted with respect to any of the technology described in this manual. Net Optics retains all intellectual property rights associated with the technology described in this manual. This manual is intended to assist with installing Net Optics products into your network.
Fiber Tap Introduction Get total traffic visibility for monitoring and security devices by placing Net Optics Fiber Slim Taps on critical network links. The all-optical design of the Fiber Tap is optimized and tested for high-performance on fiber networks. Available in LC connector types for singlemode or multimode fiber networks runing at ATM, Gigabit and 10 GigaBit speeds.
Fiber Tap Key Features Passive, Secure Technology • Provides passive access without data stream interference or introducing a point of failure • All-optical design is optimized and tested for fiber networks • Permanent in-line installation without affecting network performance • Passes all full-duplex traffic (including errors) from all layers for comprehensive troubleshooting • No IP address is needed for the Tap or monitoring device, enhancing monitoring security • Completely transparent to the network
Fiber Tap About This Guide Please read this guide before attempting to install the Fiber Tap.
Fiber Tap Unpacking and Inspection Carefully unpack the Fiber Tap and check for damaged or missing parts. The Fiber Tap ships with the following: • Fiber Tap • Test report • Installation Guide You may have also ordered a panel for rack mounting and an extended warranty. Carefully check the packing slip against parts received. If any part is missing or damaged, contact the Net Optics Customer Service Department immediately.
Fiber Tap Connecting to the Network 1. Connect Network Port A to the appropriate network device using a Duplex LC cable. 2. Connect Network Port B to the appropriate network device using a Duplex LC cable. 3. Verify that the Tap Network Ports are cabled in-line between two devices. Note:_________________________________________________________________ The use of Singlemode (8.5μm), Multimode (50μm or 62.5μm), or LC cabling is determined by the model purchased.
Fiber Tap Connecting to the Monitoring Device 1. Connect to the Monitor Port using the included custom LC analyzer cable. 2. Connect one side of the twin-duplex fiber cable into a RX port on the monitoring device to view one side of the full-duplex link. 3. Connect the other side of the twin-duplex fiber cable into another RX port on the monitoring device to view the other side of the full-duplex link. 4. Verify that the Tap Monitor Port is cabled to the monitoring device.
Fiber Tap Specifications Splitter Specifications Fiber Type: Corning Multimode 62.5/125µm, wavelength 850nm Corning Multimode 50/125µm, wavelength 850nm Split Ratio 50/50 80/20 70/30 60/40 90/10 Network Port Insertion Loss Monitor Port Insertion Loss ≤ 1.8 dB ≤ 8.1 dB ≤ 4.5 dB ≤ 4.5 dB ≤ 2.4 dB ≤ 6.3 dB ≤ 3.1 dB ≤ 5.1 dB ≤ 1.3 dB ≤ 11.5 dB Fiber Type: Corning Singlemode 8.5/125µm, wavelength 1310nm Corning Singlemode 8.
Fiber Tap Labels The product label shown here can be found on the top cover of the Tap.
Fiber Tap In addition, the label shown here prevent you from taking the cover off of the unit without voiding your warranty. You should not take the cover off because there are no user‑serviceable parts inside.
Fiber Tap Limitations on Warranty and Liability Net Optics offers a limited warranty for all its products. IN NO EVENT SHALL NET OPTICS, INC. BE LIABLE FOR ANY DAMAGES INCURRED BY THE USE OF THE PRODUCTS (INCLUDING BOTH HARDWARE AND SOFTWARE) DESCRIBED IN THIS MANUAL, OR BY ANY DEFECT OR INACCURACY IN THIS MANUAL ITSELF.
