- NetOptics Installation Guide Hub/Switch N-IDP-POBPSX-001, N-IDP-POBPLX-002

ManualsBrandsNet Optics ManualsSwitchN-IDP-POBPSX-001, N-IDP-POBPLX-002

Installation Guide for

Optical Bypass Switch

Models N-IDP-POBPSX-001, N-IDP-POBPLX-002

Doc. IGNET-N-IDP-POBPSX-001/LX-002 Revised 09/05

Summary of content (12 pages)

PAGE 1
Installation Guide for Optical Bypass Switch Models N-IDP-POBPSX-001, N-IDP-POBPLX-002 Doc.
PAGE 2
Optical Bypass Switch Table of Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Key Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
Optical Bypass Switch PLEASE READ THESE LEGAL NOTICES CAREFULLY. By using a Net Optics Optical Bypass Switch you agree to the terms and conditions of usage set forth by Net Optics, Inc.. . No licenses, express or implied, are granted with respect to any of the technology described in this manual. Net Optics retains all intellectual property rights associated with the technology described in this manual. This manual is intended to assist with installing Net Optics products into your network.
PAGE 4
Optical Bypass Switch Introduction Net Optics Optical Bypass Switches provide a permanent and trouble-free access port for in-line network security and monitoring devices. The Optical Bypass Switch automatically switches network traffic through added IDP devices or bypasses devices that are about to be removed. Prevent link failure when attached IDP devices lose power by powering the Bypass Switch and in-line device from the same power source.
PAGE 5
Optical Bypass Switch Key Features (continued) Ease of Use • • • • LED indicator shows power status Front-mounted connectors support easy installation and operation Cables included for plug-and-play deployment Silk-screened application diagram illustrates all connections for easy deployment • Optional 19-inch rack frames holds two Bypass Switches • Tested and compatible with all major manufacturers’ monitoring devices, including protocol analyzers, probes, and intrusion detection/prevention systems Supp
PAGE 6
Optical Bypass Switch Product Diagram Optical Bypass Switch ® A A B OUT IN OUT IN OUT IN Network GigaBit 96470 B Monitor OUT IN www.netoptics.com Network Ports A & B Monitor Ports A & B Figure 1. Front View Panel Silk Screen Diagram Power Connector ® ® x T x R A x T x R B x T x R Network A A x T x B R Network B Monitor A Monitor B Figure 2.
PAGE 7
Optical Bypass Switch Power Loss Bypass The Optical Bypass Switch protects link integrity when the in-line appliance loses power. When the Bypass Switch is receiving power it is in Bypass Disabled (OFF ) mode. In Bypass Disabled mode the switch sends network traffic through the connnected device. Bypass Disabled Mode 1 When the Bypass Switch is in Bypass Disabled mode, all in-line traffic is routed through the Juniper IDP appliance.
PAGE 8
Optical Bypass Switch Unpacking and Inspection Unpack the Optical Bypass Switch, power supply, and cables provided. Each Optical Bypass Switch is delivered with the following: For models N-IDP-POBPSX-001, N-IDP-POBPLX-002: • 1 DC power supply • 2 Duplex SC-SC fiber cables • 2 Duplex SC-LC fiber cables • 1 Manual If any component is missing or damaged, contact Net Optics Customer Service immediately. Connecting the Optical Bypass Switch to the Network 1.
PAGE 9
Optical Bypass Switch Connecting the Optical Bypass Switch to the In-line Security Device 1. Connect Monitoring Port A to the in-line appliance Port A using a duplex SC-to-LC fiber cable. This will act as your DCE Interface. 2. Connect Monitoring Port B to the in-line appliance Port B using a duplex SC-to-LC fiber cable. This will act as your DTE interface. 3. Verify that the Switch Monitoring Ports are cabled in-line between two devices. 4. Connect the power supply to the switch.
PAGE 10
Optical Bypass Switch Specifications Splitter Specifications: Fiber Type: Multimode: Corning 62.5/125µm, wavelength, 850nm Insertion Loss: Network Port: ≤ 1.25 dB Monitor Port: ≤ 1.25 dB Fiber Type: Singlemode: Corning 8.5/125µm, wavelength, 1300nm Insertion Loss: Network Port: ≤ 1.25 dB Monitor Port: ≤ 1.25 dB Note: There is no insertion loss when the switch is not receiving power and is in Bypass Disabled mode.
PAGE 11
Optical Bypass Switch Limitations on Warranty and Liability Net Optics offers a limited warranty for all its products. IN NO EVENT SHALL NET OPTICS, INC. BE LIABLE FOR ANY DAMAGES INCURRED BY THE USE OF THE PRODUCTS (INCLUDING BOTH HARDWARE AND SOFTWARE) DESCRIBED IN THIS MANUAL, OR BY ANY DEFECT OR INACCURACY IN THIS MANUAL ITSELF.