NE ETCOMM M LIBERT TY™ SER RIES HSPA+ H + WiF Fi 3G G22WV V
NETCOMM LIBERTY™ SERIES - USSER GUIDE G E pyright Cop Copyright©2012 NetCom mm Wireless Limited. All rights reserved. a means without prrior The information contained herein is proprietarry to NetComm Wireless Limited. No part of this document maay be translated, transcribed, reproducedd, in any form, or by any writteen consent of NetComm Wireless Limitedd. Please note: TThis document is subbject to change withoout notice. YMLL22WVI wwww.netcomm.
Sav ve Our Environnment Wheen this equipment hass reached the end off its useful life, it mustt be taken to a recyclling centre and proceessed separately from m domestic waste. The cardboard box, the pplastic contained in the packaging, and thhe parts that make upp this device can be recycled in accordance with regionally eestablished regulationns. Never dispose of this b subject to penaltiees or sanctions undeer the law. Instead, assk for disposal instrucctions from your munnicipal government.
NETCOMM LIBERTY™ SERIES Troubleshooting the Voice Function ....................................................................................................................................................................................................................................................................................... 60 Technical Data ....................................................................................................................................
Overvi O iew Inttroduction This manual provides infoormation related to thhe installation, operattion, and utilisation off the 3G22WV. Taarget Userss The individual reading this manual is presumeed to have a basic unnderstanding of teleccommunications term minology and concepts. Prrerequisitess Befoore continuing with the installation of your 3G22WV, please connfirm that you complyy with the minimum system s requirements below. a activated mobile broa adband SIM card.
NETCOMM LIBERTY™ SERIES - Product Introduction Product Overview 1. Quad-Band HSPA+ (where network is available) Up to 21Mbps downlink / 5.76Mbps uplink1 1 x Voice ports (circuit-switched) 3 x 10/100 LAN Ethernet port 1 x 10/100/1000 LAN / WAN Ethernet port for optional alternate Internet connectivity (ADSL/Cable/Satellite) 802.11n/300Mbps Wireless1 (Backward compatible with 802.
Physic P cal Dim menssions aand Indicaators LEED Indicatoors The 3G22WV has been ddesigned to be placeed on a desktop. All of o the cables exit fromm the rear for better organization. o The dispplay is visible on the front of the 3G22WV to provide you with inforrmation about networrk activity and the devvice status. See beloow for an explanation of each of the indicaator lights.
NETCOMM LIBERTY™ SERIES - Integrated Interfaces The following integrated interfaces are available at the rear of the 3G22WV: INTERFACE FUNCTION SIM Slot Insert your SIM card here (until you hear a click). Please be careful to insert the SIM in the correct orientation by viewing the printed icon. 3G Antenna Connector Attach an (optional) external 3G Antenna here. LAN 4 - 2 LAN Port for wired Ethernet clients (Computers, Laptops, etc.
Phhysical Dim mensions The following page lists tthe physical dimensioons of the 3G22WV. Figure 1 ‐ 3G22WV Dimenssions 33G22WV DIMENSIONNS Lengthh 160mm Heighht 195 mm Widthh 65 mm Weighht 250 grams Taable 4 ‐ Device Dimeensions 3G G22WV Default Settinngs The following tables list thhe default settings foor the 3G22WV. LAN (MANAGEMENTT) Staticc IP Address: 192.168.20.1 Subnnet Mask: 255.255.255.0 Default Gateway: 192.168.20.
NETCOMM LIBERTY™ SERIES - Safety S y and Produuct Care With reference to unpackking, installation, use and maintenance of your electronic devicce, the following bassic guidelines are recommended: To avooid fire or shock hazaard do not use or insttall this product nearr water. For example, near a bathtub, kitchhen sink, laundry tubb, or near a swimmingg pool. Also, do not exposse the equipment to rain r or damp areas (ee.g. a wet basement) .
Innstallaation and Config C guratiion off the 33G22W WV Plaacement oof your 3G222WV Just like your mobile phoone, the 3G22WV’s loocation will affect its signal s strength to the Mobile Broadband Base B Station (Cell Tow wer). The data speedd achievable from thee 3G22WV is relative to this signal s strength, whicch is affected by many environmental factors.
NETCOMM LIBERTY™ SERIES - Hardware installation 1. 2. 3. 4. 5. Insert your SIM card (until you hear a click) into the SIM slot. For voice functionality, connect a standard analogue telephone to the port labelled “Voice” using the RJ-11 cable provided. Connect the power adapter to the Power socket on the back of the 3G22WV. Plug the power adapter into the wall socket and switch on the power. Wait approximately 60 seconds for the 3G22WV to power up. Connecting via a cable 1. 2. 3. 4. 5. 6.
Maanagemennt Console Login Proccedure Afterr first time setup, the management console will be password protected p to prevent uunauthorized accesss to the configuration settings of your 3G222WV. ment console and vieww the status and makke changes to your 33G22WV, please folloow the steps below: To loog in to the managem 1. 2. Open your wweb browser (e.g. Inteernet Explorer/Firefoxx/Safari) and navigatee to http://192.168.200.1 or http://my.
NETCOMM LIBERTY™ SERIES Wirreless Figure 4 ‐ Basic V View – Wireless k This page allows you to cconfigure basic WiFi settings for this devicce such as enabling//disabling the WiFi functionality, changingg the Wireless Networrk Name (SSID) or the Wireless Security key. OOPTION DEFINITION Wireless (WiFi) Select the On or Offf option to disable or enab le the Wireless functionalityy. WiFi Network Nam me (SSID) The SSID (Service Set S Identifier) is the name oof your wireless network.
Inteernet Figure 5 ‐ Basic View – Intern net o this page. Please see s the table below fofor options allowed foor the 3G operation mode: m The 3G Operation Mode can be configured on OOPTION DEFINITION Automatically Connfigure My Mobile Broadband The router will attem mpt to automatically detectt the mobile broadband proovider and APN of the inserted SIM car. If your SIM caard has a PIN code or requuires a username or passw word to connect do not seleect this option.
NETCOMM LIBERTY™ SERIES - Addvanced Feeatures The basic configuration interface is intended to provide access to all the settings that mmost people will wannt to use on their 3G22WV. There are advaanced settings availaable if desired which are acceessible by viewing the advanced settings pages. Hom me Clickking the Home menu item will return you to t the Basic View pagge.
The LAN1 port can also ooperate as a WAN poort for connecting to a bridged Ethernet ddevice such as an xDDSL modem. Using the pull down menu in the “Ethernet Port Sttatus” section, selectt the LAN1 mode applicable foor your environment. To view the LAN, PPPoE or Call Forwarding status, click on the relevant link below the green menu bar. Eacch of these sections is hidden by default. To view them all, clicck on the “All Status”” o information relevant to the connection tyype or function. buttoon.
NETCOMM LIBERTY™ SERIES Inteernet Settings Mo obile Broadbandd Con nnection This page allows you to ssetup your WWAN (W Wireless Wide Area Network) connection. Figure 10 ‐ Advannced View – Mobilee Broadband Connection Settings OOPTION DEFINITION Profile Name A name to identify the profile and associated mmobile broadband settingss. APN Name Enter the APN namee you wish to use to conneect to your mobile broadband provider. Please don’t edit e this unless you are awaare of what effect it will havve.
Ban nd Settings The band settings page eenables you to selecct which frequency baand you will use for yyour connection and enable e you to scan foor available network ooperators in your areea. Figure 11 ‐ Advannced View – Band Selection S a for the maajority of users. The default setting of “All bands” should be appropriate You can also scan for available mobile broadband service provideers in your area by seelecting “Manual” forr the “Current Operator Selection Mode” aand then clicking the scan button.
NETCOMM LIBERTY™ SERIES SIM M Security The SIM Security page enables you to configure SIM PIN related functions f such as stooring the PIN in use on o the SIM or changinng the PIN protectionn status. Figure 13: Mobille Broadband ‐ SIM Security ITEM DEFINITION SIM Status The current status of o the inserted SIM. Number of Retriess Remaining The remaining number of times an incorrect SSIM PIN can be entered beffore being prompted to entter a PUK code.
LA AN IP Setup S The LAN functionality of tthe 3G22WV can be configured from this page. Using this pagge, a user can changge the LAN IP, LAN Subnet S and DNS Massquerading options. Figure 14 ‐ Advannced View ‐ LAN Settings Please notee: If the IP address haas changed you will have h to re-enter the nnew IP address configured in your browseer to access the conffiguration pages. OPTION DESCRIPTION IP Address The local IP address oof 3G22WV Subnet Mask The subnet mask for tthe local network.
NETCOMM LIBERTY™ SERIES DH HCP The DHCP page is used to adjust the DHCP settings s used by the router. The DHCP seettings are then passeed onto any device connecting c via DHCPP. L time, the defauult Domain name suffix, Primary and Secondary DNS Server, thhe Primary and Secoondary WINS Server, as You can manually set thee DHCP Start and Endd range, the DHCP Lease well as the NTP, TFTP annd Option 150/Optionn 160 (VoIP options) settings.
NetCComm 3G22WV-I - HSPPA+ WiFi Router with Voice User Guide 23 YML222WVI www.netcomm m.
NETCOMM LIBERTY™ SERIES LA AN - Advanced Setup c by experieenced administratorss. The following pagee provides a brief oveerview of the featuress available. The Advanced Setup LAN page has settings that should only be configured Figure 18: Internnet Settings ‐ LAN ‐ Advanced A Setup FIELD DESCRIPTION 802.1d Spanning Trree Thhe default is “Disable”, seleect “Enable” to enable this option.
WA AN The WAN page allows yoou to configure the opptional WAN Ethernett port. Select the WAAN connection type suuitable for your enviroonment and configure re parameters accordding to the selected connnection type. STAATIC (fixed IP) If your WAN connection uuses a static IP addreess, please select “SSTATIC (fixed IP)” andd fill in the required innformation in the fieldds provided.
NETCOMM LIBERTY™ SERIES PPPPoE m is in bridge mode. Most ADSL/ADSL2+ servvices use the PPP oveer Ethernet protocol. Use this protocol if yyou are utilising a fixeed line broadband seervice especially if thee connecting modem Figure 21: Advannced View ‐ WAN ‐ PPPoE P Mode Setting gs Please refer to the WAN Failover Backup section on page 27 for informattion on configuring thhe WAN failover feature and enabling the Failover notification function.
WAAN Failover Backkup The WAN Failover Backuup feature of NetComm Wireless 3G22WVV is designed to provi de a backup Mobile Broadband (MBB) Innternet connection inn the event your primaary Ethernet WAN connnection should fail. e and a MBB WAN N connection. To use this feature, you wwill need both an Etheernet WAN connectioon (from an xDSL moodem/ISDN/Satellite etc.
NETCOMM LIBERTY™ SERIES USSD The USSD page is used tto send USSD (short SMS style) messagees to the mobile broaadband service providder. Figure 222 ‐ Advanced View – USSD USSD is a real-time messsaging service usually utilised to perform mobile account relatted tasks such as thee following: Checcking available crediit for a mobile servicee account. Obtaaining more credit forr a mobile service acccount. Veriffying your mobile acccount information.
Wirreless Settings Bassic Configuratioon Settings This page allows you to ddefine the basic wireless settings for the 3G22WV. 3 Figure 23 – Advaanced View – WiFi Settings S Radio On/Off: WiFi is turned on by defaault. Changing this opption to OFF will turn OFF the wireless fun ctionality on the 3G222WV and you will nott be able to connect to your 3G22WV wireelessly. OOPTION DEFINITION Radio On/Off Use this option to switcch the wireless functionalityy on or off.
NETCOMM LIBERTY™ SERIES Seccurity Settings This section allows you too configure the wireleess security for your 3G22WV. 3 Setting up sufficient wireless seecurity can prevent unauthorized access tto your wireless netwwork. Figure 24 ‐ Advannced View ‐ WiFi Seecurity Settings OPPTION Network Authenticcation DEFINITION D Select the security mode foor the wireless network.
WEPP WEPP (Wireless Encryption Protocol) helps preevent against unwantted wireless users acccessing your 3G22W WV. It offers a lower leevel of security in commparison to WPA-PSK and WPA2-PSK. Ennter the Security S Key you wouuld like to use in the WEP W Key 1 field. Figure 25: Advannced View ‐ WiFi Seccurity Settings ‐WEP P WPAA1/WPA2 WPAA (WiFi Protected Acccess) authentication is suitable for enterprise applications.
NETCOMM LIBERTY™ SERIES Yourr 3G22WV uses WPAA2-PSK by default. Chheck your Wireless Security Card or the ddevice label on the boottom of the 3G22WVV for your default SSIDD and Security key too begin connecting your y wireless devicces. 802.1x In orrder to use 802.1X seecurity, you need to have h a RADIUS serveer on your network thaat will act as the authhentication server. Pleease type in the detaails for your RADIUS server s in the fields requuired.
Adv vanced Wirelesss Settings This page allows you to m modify the advancedd wireless settings forr your NetComm Smaart Hub 4G. These seettings should not be changed unless youu are aware of what effect e they will have. Figure 29: Advannced View ‐ Wireless ‐ Advanced Settings d on the advancced wireless settingss page please see thee table on the followinng page. For details NetCComm 3G22WV-I - HSPPA+ WiFi Router with Voice V User Guide 33 YML222WVI www.netcomm m.
NETCOMM LIBERTY™ SERIES OPTION DEFINITION BG Protection Mode A mechanism to enable the router to communicate with older legacy wireless network adapters that use 802.11b and 802.11g wireless protocols. Client Idle Timeout Beacon Interval: The wireless client connections will timeout if there is no data packets transmitted within the specified seconds range. The interval of time in which the wireless router broadcasts a beacon which is used to synchronize the wireless network.
MA AC Filtering f rules to proteect your wireless netwwork from malicious activity. a The filtering rules r can be used to either allow or blockk certain devices or This page allows you to ssetup MAC address filtering computers from accessinng the Internet. Figure 30: Advannced View ‐ Wireless ‐ MAC Filtering OPTION DEFIN TION There aree three possible options: Filtering Policy Add a MAC addreess to the filtering list Disable – MAC Filtering is disabled.
NETCOMM LIBERTY™ SERIES WD DS (Wireless D Distribution Systtem) The Wireless Distribution system allows the roouter’s network to be expanded, using coonnecting access points that are capable of using WDS mode.. There are two methods of WDS that can be empployed; WDS Bridge m mode or WDS Repeaater mode.
WPSS is the simplest way to establish a connection between wireless clients and your 33G22WV. This methodd removes the need to manually select thhe encryption mode and a enter in a passphhrase key. You only need to preess a button on both the wireless client annd the NetComm Sm mart Hub 4G router, annd the WPS feature will w complete the wireeless connection.
NETCOMM LIBERTY™ SERIES Staation Info The Station List shows the wireless clients currently associated with your 3G22WV. Figure 35 ‐ Advannced View ‐ WiFi Sttation List OPPTION DEFINITION SSID The wireless network namee. MAC Address The wireless client’s unique 12 digit hexadecimal ideentifier. Host Name The name of the computerr or device connected to thhe router. IP Address The local network address assigned to the wireless cclient by the router.
Seervices Rou uting Staatic The Static Route page is used to add or delette static routes. Staticc routes can be usedd to facilitate communnication between devvices on different netw tworks. Figure 36 ‐ Static Route Settin ngs me routes are added bby default by the routter on initialisation suuch as the Ethernet suubnet route for routinng to a device on the Ethernet subnet. A PPPP route is also addded upon obtaining a WAN Som PPP connection.
NETCOMM LIBERTY™ SERIES Click the Save button. NA AT The NAT page is used too configure the Netwoork Address Translation rules currently in use on the router. Thhe router is in NAT moode by default. The NNAT configuration settings are also knownn as Port Forwarding rules. Figuree 38 ‐ NAT Settings This is only needed if youu need to map inbound requests to a specific port on the WANN IP address to a devvice connected on the Ethernet interface, e.g. a web camera.
DM MZ If you have a client PC thhat cannot run an Inteernet application (e.gg. Games) properly frrom behind the NAT firewall, f then you cann open up the firewalll restrictions to allow unrestricted two-wayy Interrnet access by defining a DMZ Host. p going to yourr WAN port IP addresss, to a particular IP address a in your LAN.
NETCOMM LIBERTY™ SERIES Maac/IP/Port Filterring c be used to eithe r allow or block certaain users and/or portss This page allows you to ssetup MAC, IP and port filtering rules to protect your network ffrom malicious activitty. The filtering rules can from m accessing the Internnet. Figure 40: Advannced View ‐ Servicess ‐ MAC/IP/Port Filte ering OPTION DEFINITION Basic Settings MAC/IP/Port Filteering Select Enable to enable the MAC/IP/Portt Filtering feature on the 3G G22WV.
Sysstem Security This page allows you to improve the security of your 3G22WV throough the SPI (Statefull Packet Inspection) firewall f and remote access a settings. Figure 41: Advannced View ‐ Servicess ‐ Routing ‐ System Security P Inspection) fireewall to improve the ssecurity of your 3G222WV. Select to enable or disabble the SPI (Stateful Packet NetCComm 3G22WV-I - HSPPA+ WiFi Router with Voice V User Guide 43 YML222WVI www.netcomm m.
NETCOMM LIBERTY™ SERIES Con ntent Filtering This page allows you to cconfigure content, URRL and host filters to restrict improper inteernet content access from LAN computerss across one or both of the MBB and Etheernet WAN connectioons. Figure 42: Advannced View ‐ Servicess ‐ Routing ‐ Content Filtering OPTION DEFINITION Content Filter SSettings Select whhich connection type the coontent filtering will apply too.
DD DNS The DDNS page is used to configure the Dynamic DNS feature of the router. A numbe r of dynamic DNS hoosts are offered to select from. Fi Figure 43 ‐ DDNS Setttings Dynaamic DNS provides a method for the routeer to update an exterrnal name server withh the current WAN IP address. The following DDNS Provviders can be configuured with the router: To configure dynamic DNNS: 1. Click Enablee. 2. Select the Dyynamic DNS service that you wish to use. Enter your dynamic DNS account credentials. 3.
NETCOMM LIBERTY™ SERIES Sysstem Monitor The System Monitor pagee is used to configuree the behaviour of thee Periodic Ping moniitor function. Figure 45 ‐ Systeem Monitor Settingss c ping packe kets to user specified IP addresses. Should the router not receeive responses to the pings, the router willl The Periodic Ping Reset Monitor configures thhe router to transmit controlled rebooot.
SN NMP s that the 3G22WV can c The Simple Network Mannagement Protocol (SSNMP) feature can bee used to display or ccollect data from the 3G22WV that can bee sent to a network mmanagement system so m for conditioons that require administrative attention. Various V system informmation including interrface statistics, uptime, and memory usagge are available whenn viewed with an be monitored apprropriate SNMP trap m monitor.
NETCOMM LIBERTY™ SERIES SM MS The SMS tools applicatioon has been developeed to include basic SMS S functionality succh as sending a messsage, receiving a message and redirectinng an incoming message to another destinnation. a change run-time variables on the routter.
Redirect to TCP & TCP PPort, Redirect to UDP & UDP Port You can also forward inccoming text messages to a TCP/UDP baseed destination. The TTCP or UDP server caan be any kind of pubblic or private server if the server acceptss incoming text basedd message. P refer to your TCP/UDP T based SMSS server configurationn for which port to use. The TCP/UDP address caan be an IP address or domain name. The port number rangee is from 1 to 65535.
NETCOMM LIBERTY™ SERIES Inb box / Outbox The SMS Inbox page alloows a user to read, delete, reply or forwarrd an SMS message tto another mobile deevice. To Delete, Reply, or Forward an SMMS message, select thhe applicable message and click the appropriatee button for the function you would like to perform. Figure 49 ‐ Advannced View ‐ SMS ‐ Inbox The SMS Outbox page allows a user to checkk all SMS messages sent s from the 3G22W WV.
Sysstem Staartup Wizard If you wish to re-run the initial setup wizard, yoou can do so by movving the mouse over tthe System menu, annd clicking on “Start Wizard” W option. Log g The Log page is used to download or displayy the current System Log of the router. Figuree 51 ‐ System Log The System Log enabless you to troubleshoot any issues you may be experiencing withh your router.
NETCOMM LIBERTY™ SERIES Setttings The settings page is usedd to backup or restorre the routers configuuration or to reset it too factory defaults. Figure 52 ‐ Load / Save Configuratio on Page To save a copy of the router’s connfiguration Key in the administration user Password and click the Save buttonn. This will download a copyy of the current settinngs from the router too your PC.
Update Firmware This page allows you to uupgrade the 3G22WVV’s internal software. To upgrade the firmware of your 3G22WV, you need to download the upgrade image ffile to your local hard disk, and then click the Browse button annd navigate to the location of the firmware file on your computer. Once you have selected the new firmware filee, click ‘Apply’ to starrt the upgrade processs. Figure 53 ‐ Advannced View ‐ Firmwa are Update The upgrade process takkes several minutes.
NETCOMM LIBERTY™ SERIES Adm ministration The Administration page is used to enable or disable remote administration and set thee username / passwoord required to accesss the 3G22WV remootely. Figure 54 ‐ Admiinistration Configurration Items OPTIONN DEFINITION Firewall Settings Firewall Use this option to disable or enabble the router’s firewall. Enable HTTP Enablee or disable remote HTTP access to the router. You caan also set the port you would like remote HTTP access to be available on.
Sysstem Configuraation The System configurationn page is used to speecify an external syslog server or enable tthe diagnostics functtion. Figure 55 ‐ Systeem Configuration Iteems OPTION DEFINITION IPP / Hostname [:PORT] The IP address and port of the exterrnal syslog server you wouuld like logging information sent to. DDiagnostic Configuration Select to enable or disable the diag nostics function on the 3G22WV. DDiagnostic TCP Port The port the t diagnostic server softwware is listening on.
NETCOMM LIBERTY™ SERIES Staatistics a wireless statisticss of your 3G22WV. This page allows you to vview the LAN, WAN and Figure 56: Advannced View ‐ System – Statistics YMLL22WVI wwww.netcomm.
Log goff The logoff menu option wwill log the current useer out of the web connfiguration session. Figure re 57 ‐ Logoff boot Reb The reboot item will reboot the router. This caan be useful if you havve made configuratioon changes you wantt to implement or wannt to reboot the routeer. Figure 588 ‐ Reboot Router NetCComm 3G22WV-I - HSPPA+ WiFi Router with Voice V User Guide 57 YML222WVI www.netcomm m.
NETCOMM LIBERTY™ SERIES - Additio A onal Produ P uct Infformaation Ussing the 3G G22WV to make m and receive telephone caalls The 3G22WV provides ciircuit switched voice services via two telephony line interfacess offering the ability too make and receive telephone t calls via a regular analogue telephone using the 3G G mobbile network. Please note: Please refer to your mobile service provider for activation of yyour voice service annd information about the call charges thatt apply.
Call feature codes Quick Reference T Table The 3G22WV supports a number of call feature codes for supplem mentary services.
NETCOMM LIBERTY™ SERIES Calll Forwarding B Busy Call forwarding busy will divert all incoming calls c to a phone numbber that you desire onnly if your telephone is busy on another call. To eenable Call Forwardinng Busy, dial *67*# (Wheere directory numberr is the number you wish w to forward calls tto) Hangg up after you hear 2 low pitch beeps. To ddisable Call Forwardinng Busy, dial #67# Hangg up after you hear 2 high pitch beeps. p of the managem ment console.
Techn T ical Data D The following table lists thhe hardware specificcations of the 3G22W WV.
NETCOMM LIBERTY™ SERIES - FAQ F 1. Does the NetComm HSPA+ WiFi Router with Voice require any configurati on out of the box? No, the NettComm HSPA+ WiFi Router R with Voice is plug p and play devicee. Plug the device intoo an electrical outlet and once the status indicator lights are on, o plug in your analoogue phone and LAN cable for voice and data connectivitty. For WiFi connectivvity the SSID (Servicee Set Identifier) and network n key (passworrd) are located on the bottom of the devicce.
11. Is the NetCom mm HSPA+ WiFi Router with Voice secure; can other people acccess my wireless neetwork? The NetCom mm HSPA+ WiFi Rouuter with Voice comess configured with WPPA-PSK WiFi security enabled. When you first f access the Internnet, type 192.168.20.
NETCOMM LIBERTY™ SERIES - Appendix A: Tables Table 1 ‐ Document Revision History ........................................................................................................................... 3 Table 2 ‐ LED Indicators ................................................................................................................................................7 Table 3 ‐ Rear Panel Ports ..........................................................................................................
NetCComm 3G22WV-I - HSPPA+ WiFi Router with Voice User Guide 65 YML222WVI www.netcomm m.
NETCOMM LIBERTY™ SERIES - Legal & Regulatory Information 1. Intellectual Property Rights All intellectual property rights (including copyright and trade mark rights) subsisting in, relating to or arising out this Manual are owned by and vest in NetComm Wireless Limited (ACN 002490486) (NetComm Wireless Limited) (or its licensors). This Manual does not transfer any right, title or interest in NetComm Wireless’s (or its licensors’) intellectual property rights to you.
4. the cost of trannsporting product to and from NetComm Wireless Limited’s noominated premises iss your responsibility; 5. NetComm Wirreless Limited does not n have any liability or o responsibility undeer the Product Warranty where any cost, loss, injury or damagee of any kind, whetheer direct, indirect, consequentiall, incidental or otherwwise arises out of events beyond NetCommm Wireless Limited’s reasonable control.
NETCOMM LIBERTY™ SERIES RF Exposure Information This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Contac C ct Address: NETCOMM WIRRELESS LIMITED Head Office B 1200, Lane Covee NSW 2066 Australiaa PO Box P: +661(0)2 9424 2070 FF: +61(0)2 9424 20100 E: sales@netcommwireleess.com W: www.netcommwireles w ss.com NetCComm 3G22WV-I - HSPPA+ WiFi Router with Voice V User Guide 69 YML222WVI www.netcomm m.
