User Manual
Table Of Contents
- Contents
- Chapter 1 About This Manual
- Chapter 2 Introduction
- About the NETGEAR ProSafe 802.11g Wireless Access Point WG302
- Key Features
- AutoCell-The Self-Organizing Wireless Network
- 802.11g Standards-based Wireless Networking
- Autosensing Ethernet Connections with Auto Uplink
- Compatible and Related NETGEAR Products
- System Requirements
- What’s In the Box?
- Hardware Description
- Front Panel
- Rear Panel
- Chapter 3 Basic Installation and Configuration
- Wireless Equipment Placement and Range Guidelines
- Cabling Requirements
- Default Factory Settings
- Understanding WG302 Wireless Security Options
- Installing the WG302 Wireless Access Point
- Logging in to the WG302 Using Its Default IP Address
- Basic IP Settings
- Wireless Settings
- Security Profiles
- Before You Change the SSID and WEP Settings
- Setting up and Testing Basic Wireless Connectivity
- Configuring the Radius Server Settings
- Configuring Network Authentication
- Entering WEP Data Encryption Keys
- Restricting Wireless Access by MAC Address
- Chapter 4 Management
- Remote Management
- Using the Secure Telnet Interface
- How to Use the CLI via the Console Port
- CLI Commands
- SNMP Remote Management
- Viewing the Activity Log
- Viewing General Information
- Viewing Statistics
- Viewing the Available Wireless Station List
- Upgrading the Wireless Access Point Firmware
- Configuration File Management
- Backing up and Restoring the Configuration
- Erasing the Configuration
- Using the Reset Button to Restore Factory Default Settings
- Changing the Administrator Password
- AutoCell Rogue AP Detection
- AutoCell Rogue Station Detection
- Chapter 5 Advanced Configuration
- Understanding Advanced IP Settings for Wireless Clients
- Configuring Advanced Wireless LAN Settings
- AutoCell Overview
- AutoCell Configuration Options
- Auto RF Management
- Wi-Fi Multimedia (WMM) Setup
- Hotspot Settings
- Configuring Wireless LAN Parameters
- Wireless Bridging and Repeating
- Point-to-Point Bridge Configuration
- Multi-Point Bridge Configuration
- Repeater with Wireless Client Association
- Configuring NAT
- Configuring QoS Queues
- Setting up Guest Access
- Chapter 6 Troubleshooting
- No lights are lit on the access point.
- The Wireless LAN activity light does not light up.
- The LAN light is not lit.
- I cannot access the Internet or the LAN with a wireless capable computer.
- I cannot connect to the WG302 to configure it.
- When I enter a URL or IP address I get a timeout error.
- Using the Reset Button to Restore Factory Default Settings
- Appendix B Wireless Networking Basics
- Wireless Networking Overview
- Infrastructure Mode
- Ad Hoc Mode (Peer-to-Peer Workgroup)
- Network Name: Extended Service Set Identification (ESSID)
- Authentication and WEP Data Encryption
- 802.11 Authentication
- Open System Authentication
- Shared Key Authentication
- Overview of WEP Parameters
- Key Size
- WEP Configuration Options
- Wireless Channels
- WPA and WPA2 Wireless Security
- How Does WPA Compare to WEP?
- How Does WPA Compare to WPA2 (IEEE 802.11i)?
- What are the Key Features of WPA and WPA2 Security?
- Is WPA/WPA2 Perfect?
- Product Support for WPA/WPA2
- Appendix C Command Line Reference
Reference Manual for the NETGEAR ProSafe 802.11g Wireless Access Point WG302
C-2 Command Line Reference
v0.1, December 2005
The following table shows a feature-by-feature comparison of which settings can be configured
through the CLI or the Web UI, and which are configurable with either.
Table 8-1.
Feature or Setting Configurable from CLI
Configurable
from Web UI
Basic Settings
• Getting/changing Administrator Password
• Getting/changing AP name and location
Viewing information like MAC, IP address, and Firmware
version
yes yes
User Accounts yes yes
User Database Backup and Restore You cannot backup or
restore a user database
from the CLI.
yes
Sessions The CLI does not provide
session monitoring
information.
Use the Web UI to view
client sessions.
yes
Channel Management You cannot configure
Channel Management
from the CLI. .
yes
Status yes yes
Ethernet (Wired) Interface yes yes
Wireless Interface yes yes
Security yes yes
Set Up Guest Access yes yes
Enable/Configure Guest Login Welcome Page yes
Configuring Multiple BSSIDs on Virtual Wireless
Networks
yes yes
Radio Settings yes yes
MAC Filtering yes yes
Load Balancing yes yes
Quality of Service yes yes
Wireless Distribution System yes yes
Time Protocol yes yes