User Manual
Table Of Contents
- Contents
- Chapter 1 About This Manual
- Chapter 2 Introduction
- About the NETGEAR ProSafe 802.11g Wireless Access Point WG302
- Key Features
- AutoCell-The Self-Organizing Wireless Network
- 802.11g Standards-based Wireless Networking
- Autosensing Ethernet Connections with Auto Uplink
- Compatible and Related NETGEAR Products
- System Requirements
- What’s In the Box?
- Hardware Description
- Front Panel
- Rear Panel
- Chapter 3 Basic Installation and Configuration
- Wireless Equipment Placement and Range Guidelines
- Cabling Requirements
- Default Factory Settings
- Understanding WG302 Wireless Security Options
- Installing the WG302 Wireless Access Point
- Logging in to the WG302 Using Its Default IP Address
- Basic IP Settings
- Wireless Settings
- Security Profiles
- Before You Change the SSID and WEP Settings
- Setting up and Testing Basic Wireless Connectivity
- Configuring the Radius Server Settings
- Configuring Network Authentication
- Entering WEP Data Encryption Keys
- Restricting Wireless Access by MAC Address
- Chapter 4 Management
- Remote Management
- Using the Secure Telnet Interface
- How to Use the CLI via the Console Port
- CLI Commands
- SNMP Remote Management
- Viewing the Activity Log
- Viewing General Information
- Viewing Statistics
- Viewing the Available Wireless Station List
- Upgrading the Wireless Access Point Firmware
- Configuration File Management
- Backing up and Restoring the Configuration
- Erasing the Configuration
- Using the Reset Button to Restore Factory Default Settings
- Changing the Administrator Password
- AutoCell Rogue AP Detection
- AutoCell Rogue Station Detection
- Chapter 5 Advanced Configuration
- Understanding Advanced IP Settings for Wireless Clients
- Configuring Advanced Wireless LAN Settings
- AutoCell Overview
- AutoCell Configuration Options
- Auto RF Management
- Wi-Fi Multimedia (WMM) Setup
- Hotspot Settings
- Configuring Wireless LAN Parameters
- Wireless Bridging and Repeating
- Point-to-Point Bridge Configuration
- Multi-Point Bridge Configuration
- Repeater with Wireless Client Association
- Configuring NAT
- Configuring QoS Queues
- Setting up Guest Access
- Chapter 6 Troubleshooting
- No lights are lit on the access point.
- The Wireless LAN activity light does not light up.
- The LAN light is not lit.
- I cannot access the Internet or the LAN with a wireless capable computer.
- I cannot connect to the WG302 to configure it.
- When I enter a URL or IP address I get a timeout error.
- Using the Reset Button to Restore Factory Default Settings
- Appendix B Wireless Networking Basics
- Wireless Networking Overview
- Infrastructure Mode
- Ad Hoc Mode (Peer-to-Peer Workgroup)
- Network Name: Extended Service Set Identification (ESSID)
- Authentication and WEP Data Encryption
- 802.11 Authentication
- Open System Authentication
- Shared Key Authentication
- Overview of WEP Parameters
- Key Size
- WEP Configuration Options
- Wireless Channels
- WPA and WPA2 Wireless Security
- How Does WPA Compare to WEP?
- How Does WPA Compare to WPA2 (IEEE 802.11i)?
- What are the Key Features of WPA and WPA2 Security?
- Is WPA/WPA2 Perfect?
- Product Support for WPA/WPA2
- Appendix C Command Line Reference
Reference Manual for the NETGEAR ProSafe 802.11g Wireless Access Point WG302
Advanced Configuration 5-3
v0.1, December 2005
Configuring Advanced Wireless LAN Settings
This section describes the advanced wireless settings menu, which enables configuration of the
following features:
• AutoCell RF management
• Wi-Fi multimedia (WMM) setup
• Hotspot settings
• Advanced wireless parameters
AutoCell Overview
AutoCell provides advanced RF wireless management features that improve performance and
enhance security.
AutoCell’s self-organizing micro cells provide an additional level of privacy for enterprises.
AutoCell clients are highly-recommended for Enhanced RF Security.
Table 5-1. What does AutoCell do?
Problem AutoCell Settings
Erosion of privacy You can enable these two settings:
• Enhanced RF Security (Default: Disabled): Makes your Wi-Fi network
nearly undetectable by neighbors and hackers.
• Rogue Device Detection (Default: Disabled): Blocks rogue wireless
devices from connecting to your network.
Diminishing performance from
multiple APs installed in one
area.
The Auto RF Management feature (Default: Enabled) manages APs
and clients load-balance traffic across underutilized APs.
Complexity of installation With the Auto RF Management feature (Default: Enabled), the APs can
be put in any convenient location and in any density.
Increasing interference The Auto RF Management feature (Default: Enabled) lets clients and
APs avoid interference from neighbors and other unexpected sources.