Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 202-10090-02 v 1.
© 2005 by NETGEAR, Inc. All rights reserved. April 2005. Trademarks NETGEAR is a trademark of Netgear, Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Other brand and product names are registered trademarks or trademarks of their respective holders. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice.
Voluntary Control Council for Interference (VCCI) Statement This equipment is in the second category (information equipment to be used in a residential area or an adjacent area thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas. When used near a radio or TV receiver, it may become the cause of radio interference.
iv 202-10090-02 v 1.
Contents Chapter 1 About This Manual Audience, Scope, Conventions, and Formats ................................................................1-1 How to Use This Manual ................................................................................................1-2 How to Print this Manual .................................................................................................1-3 Chapter 2 Introduction Key Features ...............................................................................
Scheduling When Blocking Will Be Enforced .................................................................4-4 Configuring E-Mail Alert and Web Access Log Notifications ..........................................4-5 Viewing Logs of Web Access or Attempted Web Access ...............................................4-6 Chapter 5 Maintenance Viewing Wireless Router Status Information ...................................................................5-1 Viewing a List of Attached Devices ........................
Power LED Not On ...................................................................................................7-1 LEDs Never Turn Off ................................................................................................7-2 Local or Internet Port LEDs Not On .........................................................................7-2 Troubleshooting the Web Configuration Interface ..........................................................7-3 Troubleshooting the ISP Connection ...............
Appendix C Preparing Your Network Preparing Your Computers for TCP/IP Networking ....................................................... C-1 Configuring Windows 95, 98, and Me for TCP/IP Networking ....................................... C-2 Install or Verify Windows Networking Components ................................................. C-2 Enabling DHCP to Automatically Configure TCP/IP Settings ................................. C-4 Selecting Windows’ Internet Access Method ...............................
Overview of WEP Parameters ................................................................................ D-5 Key Size .................................................................................................................. D-6 WEP Configuration Options .................................................................................... D-7 Wireless Channels .........................................................................................................
x Contents 202-10090-02 v 1.
Chapter 1 About This Manual This chapter describes the intended audience, scope, conventions, and formats of this manual. Audience, Scope, Conventions, and Formats This reference manual assumes that the reader has basic to intermediate computer and Internet skills. However, basic computer network, Internet, firewall, and VPN technologies tutorial information is provided in the Appendices and on the Netgear website. This guide uses the following typographical conventions: Table 1-1.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 How to Use This Manual The HTML version of this manual includes the following: • Buttons, at a time and , for browsing forwards or backwards through the manual one page • A button that displays the table of contents and an button. Double-click on a link in the table of contents or index to navigate directly to where the topic is described in the manual. • A product model.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 How to Print this Manual To print this manual you can choose one of the following several options, according to your needs. • Printing a Page in the HTML View. Each page in the HTML version of the manual is dedicated to a major topic. Use the Print button on the browser toolbar to print the page contents. • Printing a Chapter. Use the PDF of This Chapter link at the top left of any page.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 1-4 About This Manual 202-10090-02 v 1.
Chapter 2 Introduction Congratulations on your purchase of the NETGEAR® WGT624 v3 108 Mbps Wireless Firewall Router. The WGT624 v3 wireless router provides connection for multiple computers to the Internet through an external broadband access device (such as a cable modem or DSL modem) that is normally intended for use by a single computer. This chapter describes the features of the NETGEAR WGT624 v3 108 Mbps Wireless Firewall Router.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • Flash memory for firmware upgrade. 802.11g Wireless Networking The WGT624 v3 wireless router includes an 802.11g wireless access point, providing continuous, high-speed 54 Mbps access between your wireless and Ethernet devices. The access point provides: • 802.11g wireless networking at up to 108 Mbps. • 802.11g wireless networking, with the ability to operate in 802.11g-only, 802.11b-only, or 802.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • The WGT624 v3 prevents objectionable content from reaching your PCs. The router allows you to control access to Internet content by screening for keywords within web addresses. You can configure the router to log and report attempts to access objectionable Internet sites. Security The WGT624 v3 wireless router is equipped with several features designed to maintain security, as described in this section.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • IP Address Sharing by NAT The WGT624 v3 wireless router allows several networked PCs to share an Internet account using only a single IP address, which may be statically or dynamically assigned by your Internet service provider (ISP). This technique, known as NAT, allows the use of an inexpensive single-user ISP account.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • Visual monitoring The WGT624 v3 wireless router’s front panel LEDs provide an easy way to monitor its status and activity.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 The Router’s Front Panel The front panel of the WGT624 v3 wireless router contains the status LEDs described below. Figure 2-1: WGT624 v3 Front Panel You can use some of the LEDs to verify connections. Viewed from left to right, Table 2-1 describes the LEDs on the front panel of the router. These LEDs are green when lit. Table 2-1. Label LED Descriptions Activity Description On Off Power is supplied to the router.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 The Router’s Rear Panel The rear panel of the WGT624 v3 wireless router contains the port connections listed below.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 2-8 Introduction 202-10090-02 v 1.
Chapter 3 Configuring the Internet and Wireless Settings This chapter describes how to use the Smart Wizard Installation Assistant on the Resource CD to configure your wireless router’s Internet connection and wireless parameters. Once you are connected to the Internet and your wireless connections are working, you can also configure the router’s content filtering parameters if you need to change the default settings. See Chapter 4, “Content Filtering.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Initial Configuration 1. Insert the Resource CD into the CD drive on your PC. The following screen appears: Click SETUP to get started Figure 3-1: Smart Wizard Installation Assistant Startup screen 2. Click Setup and follow the instructions. The Smart Wizard Installation Assistant will guide you through the setup process: • • • 3-2 How to change your cabling. How to connect to the Internet. How to configure your wireless settings.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 If you want to change your Internet or wireless settings later, see “Changing Your Configuration” on page 3-6. Logging Into Your Router To log into your router after you have configured your router, do the following: 1. Type http://www.routerlogin.net in the address field of Internet Explorer or Netscape® Navigator. Figure 3-2: Log in to the router 2.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 3. Click OK and the resulting window below appears: Figure 3-4: Login result 3-4 Configuring the Internet and Wireless Settings 202-10090-02 v 1.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 4. Enable the Firmware Upgrade Assistant if you want the router to check for the lastest firmware everytime you log into the router (otherwise, you can check yourself manually; see “Upgrading the Router Software” on page 5-5). Figure 3-5: Firmware Upgrade Assistant popup and screen Configuring the Internet and Wireless Settings 202-10090-02 v 1.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Changing Your Configuration You can change your Internet and wireless settings after they have been configured by the Smart Wizard Configuration Assistant. Internet Settings To change the Internet settings, click Basic Settings on the left menu bar.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Click an item in the leftmost column. The current settings or information for that area appear in the center column. Helpful information related to the selected Settings page appears in this column. If you are using Internet Explorer, you may click an item in the center column to jump directly to the related help section; otherwise, scroll down until you reach it. For the most current documentation, go to: http://kbserver.netgear.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 If you have a fixed (static, permanent) IP address, your ISP will have provided you with an IP address. Select Use static IP address and type in the IP Address. • Account Name (also known as Host Name or System Name): For most users, type your account name or user name in this box. For example, if your main mail account is JerAB@ISP.com, then put JerAB in this box.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Usually, select Use Default MAC Address. If your ISP requires MAC authentication, then select either Use Computer MAC address to disguise the Router's MAC address with the Computer's own MAC address or Use This MAC Address to manually type the MAC address for a different computer. The format for the MAC address is XX:XX:XX:XX:XX:XX.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Wireless Settings To change the Internet settings, click Wireless Settings on the left menu bar. One of the following screens appears: Wireless Settings: No security Wireless Settings: WEP security Wireless Settings: WPA-PSK security Figure 3-7: Wireless Settings screens NOTE: To ensure proper agency compliance and compatibility between similar products in your area; the operating channel & region must be set correctly.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Note: Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the router. • Name (SSID): Enter a value of up to 32 alphanumeric characters. The same Name (SSID) must be assigned to all wireless devices in your network. The default SSID is NETGEAR, but NETGEAR strongly recommends that you change your network's Name (SSID) to a different value.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 – • Security Encryption (WEP) Key: If WEP is enabled, you can manually or automatically program the four data encryption keys. These values must be identical on all PCs and Access Points in your network. • Automatic Key Generation (Passphrase): Enter a word or group of printable characters in the Passphrase box and click the Generate button to automatically configure the WEP Key(s).
Chapter 4 Content Filtering This chapter describes how to use the content filtering features of the WGT624 v3 108 Mbps Wireless Firewall Router to protect your network. These features can be found by clicking on the Content Filtering heading in the Main Menu of the browser interface. The WGT624 v3 108 Mbps Wireless Firewall Router provides you with web content filtering options, plus browsing activity reporting and instant alerts via e-mail.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 To enable keyword blocking, select either “Per Schedule” or “Always”, then click Apply. If you want to block by schedule, be sure that a time period is specified in the Schedule menu. To add a keyword or domain, type it in the Keyword box, click Add Keyword, then click Apply. To delete a keyword or domain, select it from the list, click Delete Keyword, then click Apply.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Services are functions performed by server computers at the request of client computers. For example, web servers serve web pages, time servers serve time and date information, and game hosts serve data about other players’ moves. When a computer on your network sends a request for service to a server computer on the Internet, the requested service is identified by a service or port number.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Enter the Starting Port and Ending Port numbers. If the application uses a single port number, enter that number in both boxes. If you know that the application uses either TCP or UDP, select the appropriate protocol. If you are not sure, select Both.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • Time of Day to Block. Select a start and end time in 23:59 format. Select All day for 24 hour blocking. Click Apply. Note: Be sure to select your time zone in the E-Mail menu.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • Your outgoing mail server Enter the name of your ISP’s outgoing (SMTP) mail server (such as mail.myISP.com). You may be able to find this information in the configuration menu of your e-mail program. If you leave this box blank, log and alert messages will not be sent via e-mail. • My Mail Server Requires Authentication Select this checkbox and enter the user name and password for this email account, as required.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Figure 4-6: Logs menu Log entries are described in Table 4-1 Table 4-1. Log entry descriptions Field Description Number The index number of the content filter log entries. 128 entries are available numbered from 0 to 127. The log will keep the record of the latest 128 entries. Date and Time The date and time the log entry was recorded. Source IP The IP address of the initiating device for this log entry.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Log action buttons are described in Table 4-2 Table 4-2. Log action buttons Field Description Refresh Click this button to refresh the log screen. Clear Log Click this button to clear the log entries. Send Log Click this button to email the log immediately. 4-8 Content Filtering 202-10090-02 v 1.
Chapter 5 Maintenance This chapter describes how to use the maintenance features of your WGT624 v3 108 Mbps Wireless Firewall Router. These features can be found by clicking on the Maintenance heading in the Main Menu of the browser interface. Viewing Wireless Router Status Information The Router Status menu provides a limited amount of status and usage information. From the Main Menu of the browser interface, click on Maintenance, then select System Status to view the System Status screen, shown below.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 This screen shows the following parameters: Table 5-1. Menu 3.2 - Wireless Router Status Fields Field Description Account Name This field displays the Host Name assigned to the router. Firmware Version This field displays the router firmware version. Internet Port These parameters apply to the Internet (WAN) port of the router.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Click on the “Show WAN Status” button to display the WAN status, as shown below. Figure 5-2: Connection Status screen This screen shows the following statistics:. Table 5-1. Connection Status Fields Field Description Connection Time The length of time the router has been connected to your Internet service provider’s network. Connection Method The method used to obtain an IP address from your Internet service provider.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Click on the “Show Statistics” button to display router usage statistics, as shown below. Figure 5-3: Router Statistics screen This screen shows the following statistics: Table 5-1. Router Statistics Fields Field Description Port The statistics for the WAN (Internet) and LAN (local) ports. For each port, the screen displays: Status The link status of the port.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Show Statistics action buttons are described in Table 5-2 Table 5-2. Show Statistics action buttons Field Description Set Interval Enter a time and click the button to set the polling frequency. Stop Click the Stop button to freeze the polling information. Viewing a List of Attached Devices The Attached Devices menu contains a table of all IP devices that the router has discovered on the local network.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Note: Be sure to check the NETGEAR web site for documentation updates which are available at http://www.netgear.com/docs. From the Main Menu of the browser interface, under the Maintenance heading, select the Router Upgrade heading to display the menu shown below.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Configuration File Management The configuration settings of the WGT624 v3 wireless router are stored within the router in a configuration file. This file can be saved (backed up) to a user’s PC, retrieved (restored) from the user’s PC, or cleared to factory default settings. From the Main Menu of the browser interface, under the Maintenance heading, select the Settings Backup heading to bring up the menu shown below.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Erasing the Configuration It is sometimes desirable to restore the router to the factory default settings. This can be done by using the Erase function, which will restore all factory settings. After an erase, the router's password will be password, the LAN IP address will be 192.168.1.1, and the router's DHCP client will be enabled. To erase the configuration, click the Erase button.
Chapter 6 Advanced Configuration This chapter describes how to configure the advanced features of your WGT624 v3 108 Mbps Wireless Firewall Router. These features can be found under the Advanced heading in the Main Menu of the browser interface. Configuring Port Forwarding to Local Servers Although the router causes your entire local network to appear as a single machine to the Internet, you can make a local server (for example, a web server or game server) visible and available to the Internet.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Use the Port Forwarding menu to configure the router to forward incoming protocols to computers on your local network. In addition to servers for specific applications, you can also specify a Default DMZ Server to which all other incoming protocols are forwarded. The DMZ Server is configured in the WAN Setup Menu.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Local Web and FTP Server Example If a local PC with a private IP address of 192.168.1.33 acts as a web and FTP server, configure the Ports menu to forward HTTP (port 80) and FTP (port 21) to local address 192.168.1.33 In order for a remote user to access this server from the Internet, the remote user must know the IP address that has been assigned by your ISP. If this address is 172.16.1.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Some online games and videoconferencing applications are incompatible with NAT. The WGT624 v3 wireless router is programmed to recognize some of these applications and to work properly with them, but there are other applications that may not function well. In some cases, one local PC can run the application properly if that PC’s IP address is entered as the default in the PORTS Menu.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Port Triggering Rules Menu The Port Triggering Rules Menu lists the current rules: • Enable - Indicates if the rule is enabled or disabled. Generally, there is no need to disable a rule unless it interferes with some other function, such as Port Forwarding. • Name - The name for this rule. • Outgoing Ports - The port or port range for outgoing traffic. An outgoing connection using one of these ports will "Trigger" this rule.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • Incoming (Response) Port Range - enter the range of port numbers used by the remote system when it responds to the PC's request. Modifying or Deleting an existing Rule: • Select the desired rule by clicking the radio button beside the rule. • Click Edit or Delete as desired. • Checking Operation and Status Rules Status To see which rules are currently being used, click the Status button.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Configuring WAN Setup Options The WAN Setup options let you configure a DMZ server, change the MTU size and enable the wireless router to respond to a Ping on the WAN port. These options are discussed below. Figure 6-3: WAN Setup menu. • Connect Automatically, as Required Normally, this option should be enabled. An Internet connection will be made automatically after each timeout, whenever Internet-bound traffic is detected.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • Setting Up a Default DMZ Server The default DMZ server feature is helpful when using some online games and videoconferencing applications that are incompatible with NAT. The router is programmed to recognize some of these applications and to work properly with them, but there are other applications that may not function well.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Under MTU Size, enter a new size between 64 and 1500. Then, click Apply to save the new configuration. Using a Dynamic DNS Service If your network has a permanently assigned IP address, you can register a domain name and have that name linked with your IP address by public Domain Name Servers (DNS).
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 To configure Dynamic DNS: 1. Register for an account with one of the dynamic DNS service providers whose names appear in the ‘Select Service Provider’ box. For example, for dyndns.org, go to www.dyndns.org. 2. Select the Use a Dynamic DNS service check box. 3. Select the name of your dynamic DNS Service Provider. 4. Type the Host Name (or domain name) that your dynamic DNS service provider gave you. 5.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Using LAN IP Setup Options The LAN IP Setup feature is under the Advanced heading of the main menu. This feature allows configuration of LAN IP services such as DHCP and RIP. From the Main Menu of the browser interface, under Advanced, click on LAN IP Setup to view the LAN IP Setup menu, shown below.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • IP Subnet Mask This is the LAN Subnet Mask of the router. Combined with the IP address, the IP Subnet Mask allows a device to know which other addresses are local to it, and which must be reached through a gateway or router. • RIP Direction RIP (Router Information Protocol) allows a router to exchange routing information with other routers. The RIP Direction selection controls how the router sends and receives RIP packets.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 If another device on your network will be the DHCP server, or if you will manually configure the network settings of all of your computers, clear the ‘Use router as DHCP server’ check box. Otherwise, leave it checked. Specify the pool of IP addresses to be assigned by setting the Starting IP Address and Ending IP Address. These addresses should be part of the same IP address subnet as the router’s LAN IP address.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 To reserve an IP address: 1. Click the Add button. Figure 6-6: Address Reservation screen 2. In the IP Address box, type the IP address to assign to the PC or server. (choose an IP address from the router’s LAN subnet, such as 192.168.1.X) 3. Type the MAC Address of the PC or server. (Tip: If the PC is already present on your network, you can copy its MAC address from the Attached Devices menu and paste it here.) 4.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 How to Configure Static Routes Static Routes provide additional routing information to your router. Under normal circumstances, the router has adequate routing information after it has been configured for Internet access, and you do not need to configure additional static routes. You must configure static routes only for unusual cases such as multiple routers or multiple IP subnets located on your network.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 3. Select Private if you want to limit access to the LAN only. The static route will not be reported in RIP. 4. Select Active to make this route effective. 5. Type the Destination IP Address of the final destination. 6. Type the IP Subnet Mask for this destination. If the destination is a single host, type 255.255.255.255. 7. Type the Gateway IP Address, which must be a router on the same LAN segment as the router. 8.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Enabling Remote Management Access Using the Remote Management page, you can allow a user or users on the Internet to configure, upgrade and check the status of your WGT624 v3 wireless router. Note: Be sure to change the router's default configuration password to a very secure password.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 3. b. To allow access from a range of IP addresses on the Internet, select IP address range. Enter a beginning and ending IP address to define the allowed range. c. To allow access from a single IP address on the Internet, select Only this PC. Enter the IP address that will be allowed access. Specify the Port Number that will be used for accessing the management interface.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Using Universal Plug and Play (UPnP) Universal Plug and Play (UPnP) helps devices, such as Internet appliances and computers, access the network and connect to other devices as needed. UPnP devices can automatically discover the services from other registered UPnP devices on the network. Figure 6-10. UPnP Menu Turn UPnP On: UPnP can be enabled or disabled for automatic device configuration. The default setting for UPnP is enabled.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 UPnP Portmap Table: The UPnP Portmap Table displays the IP address of each UPnP device that is currently accessing the router and which ports (Internal and External) that device has opened. The UPnP Portmap Table also displays what type of port is opened and if that port is still active for each IP address. 6-20 Advanced Configuration 202-10090-02 v 1.
Chapter 7 Troubleshooting This chapter gives information about troubleshooting your WGT624 v3 108 Mbps Wireless Firewall Router. After each problem description, instructions are provided to help you diagnose and solve the problem. Note: Product updates are available on the NETGEAR Web site at www.netgear.com/support/main.asp. Documentation updates are available on the NETGEAR, Inc. Web site at www.netgear.com/docs.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • Check that you are using the 12 V DC 1A power adapter supplied by NETGEAR for this product. If the error persists, you have a hardware problem and should contact technical support. LEDs Never Turn Off When the router is turned on, the LEDs turns on for about 10 seconds and then turn off. If all the LEDs stay on, there is a fault within the router.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Troubleshooting the Web Configuration Interface If you are unable to access the router’s web Configuration interface from a PC on your local network, check the following: • Check the Ethernet connection between the PC and the router as described in the previous section. • Make sure your PC’s IP address is on the same subnet as the router.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Troubleshooting the ISP Connection If your router is unable to access the Internet, you should first determine whether the router is able to obtain a WAN IP address from the ISP. Unless you have been assigned a static IP address, your router must request an IP address from the ISP. You can determine whether the request was successful using the web Configuration Manager. To check the WAN IP address: 1. Launch your browser. 2.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 OR Configure your router to spoof your PC’s MAC address. This can be done in the Basic Settings menu. If your router can obtain an IP address, but your PC is unable to load any web pages from the Internet: • Your PC may not recognize any DNS server addresses. A DNS server is a host on the Internet that translates Internet names (such as www addresses) to numeric IP addresses.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 If the path is working, you see this message: Reply from < IP address >: bytes=32 time=NN ms TTL=xxx If the path is not working, you see this message: Request timed out If the path is not functioning correctly, you could have one of the following problems: • Wrong physical connections — Make sure the LAN port LED is on. If the LED is off, follow the instructions in “Local or Internet Port LEDs Not On” on page 7-2.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 — If your ISP assigned a host name to your PC, enter that host name as the Account Name in the Basic Settings menu. — Your ISP could be rejecting the Ethernet MAC addresses of all but one of your PCs. Many broadband ISPs restrict access by only allowing traffic from the MAC address of your broadband modem, but some ISPs additionally restrict access to the MAC address of a single PC connected to that modem.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 7-8 Troubleshooting 202-10090-02 v 1.
Appendix A Technical Specifications This appendix provides technical specifications for the WGT624 v3 108 Mbps Wireless Firewall Router.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Electromagnetic Emissions Meets requirements of: FCC Part 15 Class B VCCI Class B EN 55 022 (CISPR 22), Class B Interface Specifications LAN: 10BASE-T or 100BASE-Tx, RJ-45 WAN: 10BASE-T or 100BASE-Tx, RJ-45 Wireless Radio Data Rates 1, 2, 5.5, 6, 9, 12, 18, 24, 36, 48, 54, and 108 Mbps Auto Rate Sensing Frequency 2.4-2.
Appendix B Network, Routing, Firewall, and Basics This chapter provides an overview of IP networks, routing, and networking. Related Publications As you read this document, you may be directed to various RFC documents for further information. An RFC is a Request For Comment (RFC) published by the Internet Engineering Task Force (IETF), an open organization that defines the architecture and operation of the Internet.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Routing Information Protocol One of the protocols used by a router to build and maintain a picture of the network is the Routing Information Protocol (RIP). Using RIP, routers periodically update one another and check for changes to add to the routing table. The WGT624 v3 wireless router supports both the older RIP-1 and the newer RIP-2 protocols. Among other improvements, RIP-2 supports subnet and multicast protocols.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Class A Network Node Class B Network Node Class C Network Node 7261 Figure 7-1: Three Main Address Classes The five address classes are: • Class A Class A addresses can have up to 16,777,214 hosts on a single network. They use an eight-bit network number and a 24-bit node number. Class A addresses are in this range: 1.x.x.x to 126.x.x.x. • Class B Class B addresses can have up to 65,354 hosts on a network.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 This addressing structure allows IP addresses to uniquely identify each physical network and each node on each physical network. For each unique value of the network portion of the address, the base address of the range (host address of all zeros) is known as the network address and is not usually assigned to a host.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Subnet addressing allows us to split one IP network address into smaller multiple physical networks known as subnetworks. Some of the node numbers are used as a subnet number instead. A Class B address gives us 16 bits of node numbers translating to 64,000 nodes. Most organizations do not use 64,000 nodes, so there are free bits that can be reassigned. Subnet addressing makes use of those bits that are free, as shown below.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 The following table lists the additional subnet mask bits in dotted-decimal notation. To use the table, write down the original class netmask and replace the 0 value octets with the dotted-decimal value of the additional subnet bits. For example, to partition your Class C network with subnet mask 255.255.255.0 into 16 subnets (4 bits), the new subnet mask becomes 255.255.255.240. Table 7-1.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • So that hosts recognize local IP broadcast packets When a device broadcasts to its segment neighbors, it uses a destination address of the local network address with all ones for the host address. In order for this scheme to work, all devices on the segment must agree on which bits comprise the host address.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 The following figure illustrates a single IP address operation. Private IP addresses assigned by user IP addresses assigned by ISP 192.168.0.2 192.168.0.3 192.168.0.1 172.21.15.105 Internet 192.168.0.4 192.168.0.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 If a device sends data to another station on the network and the destination MAC address is not yet recorded, ARP is used. An ARP request is broadcast onto the network. All stations on the network receive and read the request. The destination IP address for the chosen station is included as part of the message so that only the station with this IP address responds to the ARP request. All other stations discard the request.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 IP Configuration by DHCP When an IP-based local area network is installed, each PC must be configured with an IP address. If the PCs need to access the Internet, they should also be configured with a gateway address and one or more DNS server addresses. As an alternative to manual configuration, there is a method by which each PC on the network can automatically obtain this configuration information.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Stateful Packet Inspection Unlike simple Internet sharing routers, a firewall uses a process called stateful packet inspection to ensure secure firewall filtering to protect your network from attacks and intrusions. Since user-level applications such as FTP and web browsers can create complex patterns of network traffic, it is necessary for the firewall to analyze groups of network connection states.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Category 5 Cable Quality Category 5 distributed cable that meets ANSI/EIA/TIA-568-A building wiring standards can be a maximum of 328 feet (ft.) or 100 meters (m) in length, divided as follows: 20 ft. (6 m) between the hub and the patch panel (if used) 295 ft. (90 m) from the wiring closet to the wall outlet 10 ft.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Figure B-1: Straight-Through Twisted-Pair Cable Figure B-2 illustrates crossover twisted pair cable. Figure B-2: Crossover Twisted-Pair Cable Figure B-3: Category 5 UTP Cable with Male RJ-45 Plug at Each End Network, Routing, Firewall, and Basics 202-10090-02 v 1.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Note: Flat “silver satin” telephone cable may have the same RJ-45 plug. However, using telephone cable results in excessive collisions, causing the attached port to be partitioned or disconnected from the network. Uplink Switches, Crossover Cables, and MDI/MDIX Switching In the wiring table above, the concept of transmit and receive are from the perspective of the PC, which is wired as Media Dependant Interface (MDI).
Appendix C Preparing Your Network This appendix describes how to prepare your network to connect to the Internet through the WGT624 v3 108 Mbps Wireless Firewall Router and how to verify the readiness of broadband Internet service from an Internet service provider (ISP).
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 In your IP network, each PC and the firewall must be assigned a unique IP addresses. Each PC must also have certain other IP configuration information such as a subnet mask (netmask), a domain name server (DNS) address, and a default gateway address. In most cases, you should install TCP/IP so that the PC obtains its specific network configuration information automatically from a DHCP server during bootup.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 You must have an Ethernet adapter, the TCP/IP protocol, and Client for Microsoft Networks. Note: It is not necessary to remove any other network components shown in the Network window in order to install the adapter, TCP/IP, or Client for Microsoft Networks. If you need to install a new adapter, follow these steps: a. Click the Add button. b. Select Adapter, and then click Add. c.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 If you need Client for Microsoft Networks: 3. a. Click the Add button. b. Select Client, and then click Add. c. Select Microsoft. d. Select Client for Microsoft Networks, and then click OK. Restart your PC for the changes to take effect.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Verify the following settings as shown: • Client for Microsoft Network exists • Ethernet adapter is present • TCP/IP is present • Primary Network Logon is set to Windows logon Click on the Properties button. The following TCP/IP Properties window will display. Preparing Your Network C-5 202-10090-02 v 1.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • By default, the IP Address tab is open on this window. • Verify the following: Obtain an IP address automatically is selected. If not selected, click in the radio button to the left of it to select it. This setting is required to enable the DHCP server to automatically assign an IP address. • Click OK to continue. Restart the PC. Repeat these steps for each PC with this version of Windows on your network.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 2. Type winipcfg, and then click OK. The IP Configuration window opens, which lists (among other things), your IP address, subnet mask, and default gateway. 3. From the drop-down box, select your Ethernet adapter.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 DHCP Configuration of TCP/IP in Windows XP, 2000, or NT4 You will find there are many similarities in the procedures for different Windows systems when using DHCP to configure TCP/IP. The following steps will walk you through the configuration process for each of these versions of Windows. DHCP Configuration of TCP/IP in Windows XP Locate your Network Neighborhood icon. • Select Control Panel from the Windows XP new Start Menu.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • Now you should be at the Local Area Network Connection Status window. This box displays the connection status, duration, speed, and activity statistics. • Administrator logon access rights are needed to use this window. • Click the Properties button to view details about the connection. • The TCP/IP details are presented on the Support tab page. • Select Internet Protocol, and click Properties to view the configuration information.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • Verify that the Obtain an IP address automatically radio button is selected. • Verify that Obtain DNS server address automatically radio button is selected. • Click the OK button. This completes the DHCP configuration of TCP/ IP in Windows XP. Repeat these steps for each PC with this version of Windows on your network.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • Click on the My Network Places icon on the Windows desktop. This will bring up a window called Network and Dial-up Connections. • Right click on Local Area Connection and select Properties. • The Local Area Connection Properties dialog box appears. • Verify that you have the correct Ethernet card selected in the Connect using: box.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • With Internet Protocol (TCP/IP) selected, click on Properties to open the Internet Protocol (TCP/IP) Properties dialogue box. • Verify that • Obtain an IP address automatically is selected. • Obtain DNS server address automatically is selected. • Click OK to return to Local Area Connection Properties. • Click OK again to complete the configuration process for Windows 2000. Restart the PC.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 DHCP Configuration of TCP/IP in Windows NT4 Once you have installed the network card, you need to configure the TCP/IP environment for Windows NT 4.0. Follow this procedure to configure TCP/IP with DHCP in Windows NT 4.0. • Choose Settings from the Start Menu, and then select Control Panel. This will display Control Panel window. • Double-click the Network icon in the Control Panel window. The Network panel will display.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • Highlight the TCP/IP Protocol in the Network Protocols box, and click on the Properties button. C-14 Preparing Your Network 202-10090-02 v 1.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • The TCP/IP Properties dialog box now displays. • Click the IP Address tab. • Select the radio button marked Obtain an IP address from a DHCP server. • Click OK. This completes the configuration of TCP/IP in Windows NT. Restart the PC. Repeat these steps for each PC with this version of Windows on your network. Verifying TCP/IP Properties for Windows XP, 2000, and NT4 To check your PC’s TCP/IP configuration: 1.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • 4. The default gateway is 192.168.1.1 Type exit Configuring the Macintosh for TCP/IP Networking Beginning with Macintosh Operating System 7, TCP/IP is already installed on the Macintosh. On each networked Macintosh, you will need to configure TCP/IP to use DHCP. MacOS 8.6 or 9.x 1. From the Apple menu, select Control Panels, then TCP/IP. The TCP/IP Control Panel opens: 2.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 2. If not already selected, select Built-in Ethernet in the Configure list. 3. If not already selected, Select Using DHCP in the TCP/IP tab. 4. Click Save. Verifying TCP/IP Properties for Macintosh Computers After your Macintosh is configured and has rebooted, you can check the TCP/IP configuration by returning to the TCP/IP Control Panel. From the Apple menu, select Control Panels, then TCP/IP.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Verifying the Readiness of Your Internet Account For broadband access to the Internet, you need to contract with an Internet service provider (ISP) for a single-user Internet access account using a cable modem or DSL modem. This modem must be a separate physical box (not a card) and must provide an Ethernet port intended for connection to a Network Interface Card (NIC) in a computer.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • An IP address and subnet mask • A gateway IP address, which is the address of the ISP’s router • One or more domain name server (DNS) IP addresses • Host name and domain suffix For example, your account’s full server names may look like this: mail.xxx.yyy.com In this example, the domain suffix is xxx.yyy.com. If any of these items are dynamically supplied by the ISP, your firewall automatically acquires them.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 If an IP address appears under Installed Gateways, write down the address. This is the ISP’s gateway address. Select the address and then click Remove to remove the gateway address. 6. Select the DNS Configuration tab. If any DNS server addresses are shown, write down the addresses. If any information appears in the Host or Domain information box, write it down. Click Disable DNS. 7.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Restarting the Network Once you’ve set up your computers to work with the firewall, you must reset the network for the devices to be able to communicate correctly. Restart any computer that is connected to the firewall. After configuring all of your computers for TCP/IP networking and restarting them, and connecting them to the local network of your WGT624 v3 wireless router, you are ready to access and configure the firewall.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 C-22 Preparing Your Network 202-10090-02 v 1.
Appendix D Wireless Networking Basics This chapter provides an overview of Wireless networking. Wireless Networking Overview The WGT624 v3 wireless router conforms to the Institute of Electrical and Electronics Engineers (IEEE) 802.11b and 802.11g standards for wireless LANs (WLANs). On an 802.11b or g wireless link, data is encoded using direct-sequence spread-spectrum (DSSS) technology and is transmitted in the unlicensed radio spectrum at 2.5GHz. The maximum data rate for the 802.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Ad Hoc Mode (Peer-to-Peer Workgroup) In an ad hoc network, computers are brought together as needed; thus, there is no structure or fixed points to the network - each node can generally communicate with any other node. There is no Access Point involved in this configuration.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 • Shared Key. With Shared Key authentication, only those PCs that possess the correct authentication key can join the network. By default, IEEE 802.11 wireless devices operate in an Open System network. Wired Equivalent Privacy (WEP) data encryption is used when the wireless devices are configured to operate in Shared Key authentication mode. 802.11 Authentication The 802.11 standard defines several services that govern how two 802.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 2. The access point authenticates the station. 3. The station associates with the access point and joins the network. This process is illustrated below.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 This process is illustrated below.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Key Size The IEEE 802.11 standard supports two types of WEP encryption: 40-bit and 128-bit. The 64-bit WEP data encryption method allows for a five-character (40-bit) input. Additionally, 24 factory-set bits are added to the forty-bit input to generate a 64-bit encryption key. The 24 factory-set bits are not user-configurable). This encryption key will be used to encrypt/decrypt all data transmitted via the wireless interface.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 WEP Configuration Options The WEP settings must match on all 802.11 devices that are within the same wireless network as identified by the SSID. In general, if your mobile clients will roam between access points, then all of the 802.11 access points and all of the 802.11 client adapters on the network must have the same WEP settings.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Table D-2: Channel 802.11b/g Radio Frequency Channels Center Frequency Frequency Spread 4 2427 MHz 2414.5 MHz - 2439.5 MHz 5 2432 MHz 2419.5 MHz - 2444.5 MHz 6 2437 MHz 2424.5 MHz - 2449.5 MHz 7 2442 MHz 2429.5 MHz - 2454.5 MHz 8 2447 MHz 2434.5 MHz - 2459.5 MHz 9 2452 MHz 2439.5 MHz - 2464.5 MHz 10 2457 MHz 2444.5 MHz - 2469.5 MHz 11 2462 MHz 2449.5 MHz - 2474.5 MHz 12 2467 MHz 2454.5 MHz - 2479.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 WPA and WPA2 offer the following benefits: • • • • Enhanced data privacy Robust key management Data origin authentication Data integrity protection The Wi-Fi Alliance is now performing interoperability certification testing on Wi-Fi Protected Access products. Starting August of 2003, all new Wi-Fi certified products have to support WPA. NETGEAR is implementing WPA and WPA2 on client and access point products. The 802.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 How Does WPA Compare to WPA2 (IEEE 802.11i)? WPA is forward compatible with the WPA2 security specification. WPA is a subset of WPA2 and used certain pieces of the early 802.11i draft, such as 802.1x and TKIP. The main pieces of WPA2 that are not included in WPA are secure IBSS (Ad-Hoc mode), secure fast handoff (for specialized 802.11 VoIP phones), as well as enhanced encryption protocols, such as AES-CCMP.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 The primary information conveyed in the Beacon frames is the authentication method and the cipher suite. Possible authentication methods include 802.1X and Pre-shared key. Pre-shared key is an authentication method that uses a statically configured pass phrase on both the stations and the access point. This obviates the need for an authentication server, which in many home and small office environments will not be available nor desirable.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 WPA/WPA2 Authentication: Enterprise-level User Authentication via 802.1x/EAP and RADIUS Wired Network with Optional 802.1x Port Based Network Access Control Wireless LAN WPA/WPA2 enabled wireless client with “supplicant” WPA/WPA2 enabled Access Point using pre-shared key or 802.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Client with a WPA/ WPA2-enabled wireless adapter and supplicant (Win XP, Funk, Meetinghouse) For example, a WPA/WPA2-enabled AP For example, a RADIUS server 1 2 3 4 6 5 7 Figure 4-7: 802.1x Authentication Sequence The AP sends Beacon Frames with WPA/WPA2 information element to the stations in the service set. Information elements include the required authentication method (802.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 3. The client sends an EAP-response packet containing the identity to the authentication server. The access point responds by enabling a port for passing only EAP packets from the client to an authentication server located on the wired side of the access point.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Temporal Key Integrity Protocol (TKIP) WPA uses TKIP to provide important data encryption enhancements including a per-packet key mixing function, a message integrity check (MIC) named Michael, an extended initialization vector (IV) with sequencing rules, and a re-keying mechanism. TKIP also provides for the following: • • • The verification of the security configuration after the encryption keys are determined.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Is WPA/WPA2 Perfect? WPA/WPA2 is not without its vulnerabilities. Specifically, it is susceptible to denial of service (DoS) attacks. If the access point receives two data packets that fail the message integrity code (MIC) within 60 seconds of each other, then the network is under an active attack, and as a result, the access point employs counter measures, which include disassociating each station using the access point.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Changes to Wireless Access Points Wireless access points must have their firmware updated to support the following: • • • • • The new WPA/WPA2 information element To advertise their support of WPA/WPA2, wireless APs send the beacon frame with a new 802.11 WPA/WPA2 information element that contains the wireless AP's security configuration (encryption algorithms and wireless security configuration information).
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Microsoft has worked with many wireless vendors to embed the WPA driver update in the wireless adapter driver. So, to update your Microsoft Windows wireless client, all you have to do is obtain the new WPA/WPA2-compatible driver and install the driver.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Glossary Use the list below to find definitions for technical terms used in this manual. 802.11 Standard 802.11, or IEEE 802.11, is a type of radio technology used for wireless local area networks (WLANs). It is a standard that has been developed by the IEEE (Institute of Electrical and Electronic Engineers), http://standards.ieee.org.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 802.11e Standard 802.11e is a proposed IEEE standard to define quality of service (QoS) mechanisms for wireless gear that gives support to bandwidth-sensitive applications such as voice and video. 802.11g Standard Similar to 802.11b, this physical layer standard provides a throughput of up to 54 Mbps. It also operates in the 2.4 GHz frequency band but uses a different radio technology in order to boost overall bandwidth. 802.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 A bridge connects devices that all use the same kind of protocol. A router can connect networks that use differing protocols. It also reads the addresses included in the packets and routes them to the appropriate computer station, working with any other routers in the network to choose the best path to send the packets on.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 ISA bus Wi-Fi radios. Client devices usually communicate with hub devices like access points and gateways. Collision avoidance A network node characteristic for proactively detecting that it can transmit a signal without risking a collision, thereby ensuring a more reliable connection. Crossover cable A special cable used for networking two computers without the use of a hub.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 DNS (Domain Name System) A program that translates URLs to IP addresses by accessing a database maintained on a collection of Internet servers. The program works behind the scenes to facilitate surfing the Web with alpha versus numeric addresses. A DNS server converts a name like mywebsite.com to a series of numbers like 107.22.55.26. Every website has its own specific IP address on the Internet.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Gateway In the wireless world, a gateway is an access point with additional software capabilities such as providing NAT and DHCP. Gateways may also provide VPN support, roaming, firewalls, various levels of security, etc. Hot Spot (also referred to as Public Access Location) A place where you can access Wi-Fi service. This can be for free or for a fee.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 IP (Internet Protocol) address A 32-bit number that identifies each sender or receiver of information that is sent across the Internet. An IP address has two parts: an identifier of a particular network on the Internet and an identifier of the particular device (which can be a server or a workstation) within that network.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 In a wireless mesh example, each of the spheres below represent a mesh router. Corporate servers and printers may be shared by attaching to each mesh router. For wireless access to the mesh, an access point must be attached to any one of the mesh routers. Multiple Input Multiple Output (MIMO) MIMO refers to radio links with multiple antennas at the transmitter and the receiver side to improve the performance of the wireless link.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 PHY defines parameters such as data rates, modulation method, signaling parameters, transmitter/receiver synchronization, etc. Within an actual radio implementation, the PHY corresponds to the radio front end and baseband signal processing sections. Plug and Play A computer system feature that provides for automatic configuration of add-ons and peripheral devices such as wireless PC Cards, printers, scanners and multimedia devices.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Satellite broadband A wireless high-speed Internet connection provided by satellites. Some satellite broadband connections are two-way—up and down. Others are one-way, with the satellite providing a high-speed downlink and then using a dial-up telephone connection or other land-based system for the uplink to the Internet. Server A computer that provides its resources to other computers and devices on a network.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 For example, when a web page is downloaded from a web server, the TCP program layer in that server divides the file into packets, numbers the packets, and then forwards them individually to the IP program layer. Although each packet has the same destination IP address, it may get routed differently through the network.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 node equipped with WEP. Warchalkers also draw identifiers above the symbols to indicate the password that can be used to access the node, which can easily be obtained with sniffer software. As a recent development, the debate over the legality of warchalking is still going on. The practice stems from the U.S.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 with the benefit of easier administration and use. This is similar to 802.1x support and requires a RADIUS server in order to implement. The Wi-Fi Alliance will call this, 'WPA-Enterprise.' One variation of WPA is called WPA Pre Shared Key or WPA-PSK for short - this provides an authentication alternative to an expensive RADIUS server. WPA-PSK is a simplified but still powerful form of WPA most suitable for home Wi-Fi networking.
Reference Manual for the 108 Mbps Wireless Firewall Router WGT624 v3 Wi-Fi Protected Access in "Mixed Mode" Deployment In a large network with many clients, a likely scenario is that access points will be upgraded before all the Wi-Fi clients. Some access points may operate in a "mixed mode", which supports both clients running Wi-Fi Protected Access and clients running original WEP security.
