Quick Start Guide

ManualsBrandsNetgear ManualsComputers & Accessories5G MHS Travel Router

Let’s Get Started

AT&T Eco Rating 2.0 only applies to the NETGEAR

Nighthawk 5G Mobile Hotspot, model MR5000. For

limited factors evaluated visit att.com/EcoSpace.

Wireless Emergency Alerts is a registered Trademark

and Service Mark of CTIA.

NETGEAR and Nighthawk are trademarks of

NETGEAR, Inc. 5G is a trademark of 3GPP. 5G not

available everywhere. Contains Lithium ion battery -

recycle or dispose of properly.

AT&T, the AT&T logo and all other AT&T marks

contained herein are trademarks of AT&T Intellectual

Property. All other marks are the property of their

respective owners.

Printed in USA 201-24964-01

Install the Battery

1 Insert the battery.

2 Install the back cover.

The battery is partially charged. To fully

charge it, connect the USB cable to the mobile

hotspot and then plug into either:

• A wall socket, using the wall charger (faster

charge option)

• The USB port on your laptop

Note: The mobile hotspot comes with a preinstalled SIM card.

The SIM must be activated to a data plan with AT&T.

Nighthawk® 5G Mobile Hotspot

SIM card (preinstalled)

Get to Know Your Mobile Hotspot

Touch screen

Touch to

navigate

USB C port

Power

button

Home

Back

What’s in the Box

• Nighthawk 5G Mobile Hotspot

with pre-installed SIM card

• Battery cover

• Battery

• USB Type-C cable

• AC adapter

• Quick start guide

• Warranty card

Set Up Your Mobile Hotspot

1 Press and hold the Power button for 2

seconds.

To better safeguard your network, the first

time you turn on your mobile hotspot, you

are asked to set up your login credentials.

2 Follow the onscreen instructions to

customize your mobile hotspot settings.

Signal

strength

Battery

Network

indicator

Home Screen

The Home screen displays the mobile

hotspot’s WiFi network name and password.

The network indicator lets you know which

AT&T wireless network you are connected to.

WiFi network

name and

password

Summary of content (4 pages)

PAGE 1
What’s in the Box Set Up Your Mobile Hotspot • Nighthawk 5G Mobile Hotspot with pre-installed SIM card • Battery cover • Battery • USB Type-C cable • AC adapter • Quick start guide • Warranty card 1 Press and hold the Power button for 2 seconds. To better safeguard your network, the first time you turn on your mobile hotspot, you are asked to set up your login credentials.
PAGE 2
Connect to the Internet Change the WiFi band Note: The mobile hotspot Home screen displays the WiFi network name and password. The screen goes dark to save power. Press and release the Power button to wake the screen. 1 On the home screen, tap the WiFi icon. 2 Tap Band. 3 Select the 2.4 GHz or 5 GHz WiFi band. On your laptop or other WiFi device 1 Open your WiFi network connection manager. 2 Find your mobile hotspot’s WiFi network name (ATT-WIFI-XXXX) and connect.
PAGE 3
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 4
Radiation Exposure Statement: This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.