Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 201-10080-01 Version 1.
© 2004 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR is a trademark of Netgear, Inc. Microsoft, Windows, and Windows Media Player are trademarks or registered trademarks of Microsoft Corporation. RHAPSODY is a registered trademark of Listen.com. Other brand and product names are registered trademarks or trademarks of their respective holders.
Federal Communications Commission (FCC) and European Radiation Exposure Statements This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 30 cm (12 inches) during normal operation. This device should not be co-located with other transmitters.
iv 201-10080-01
Contents Chapter 1 Getting Started with the ANT2409 Welcome .........................................................................................................................1-1 Package Contents ..........................................................................................................1-1 Pole Mount Configuration ...............................................................................................1-3 Flat Surface Mount Configuration ..........................................
vi Contents
Chapter 1 Getting Started with the ANT2409 Welcome Thank you for purchasing the NETGEAR ANT2409 antenna. This Installation Guide provides installing instructions and guidelines for using the NETGEAR 9 dBi Omni-directional Antenna. Package Contents 0OLE -OUNT "RACKET (ARDWARE , -OUNT "RACKET (ARDWARE . 3-! ADAPTER !NTENNA -OUNTING !SSEMBLY ,IGHTNING !RRESTOR M CABLE D"I /MNI $IRECTIONAL !NTENNA !.
Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 • • • • • • • • • NETGEAR Indoor / Outdoor 9 dBi 2.4 – 2.5GHz Omni-Directional Antenna ANT2409 2-meter low loss antenna cable to connect the antenna to a lightning arrestor Lightning Arrestor NOTE: a ground cable is not included but required for outdoor installation. The grounding cable must be equivalent or better than: AWG 10, UL 1015, Stranded, 600 V, 105 oC, green or green/yellow insulation, 2 clip of 5.
Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 Pole Mount Configuration This illustration shows the pole mount configuration option.
Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 Flat Surface Mount Configuration This illustration shows a flat surface mount configuration. Figure 1-3: Antenna Assembled in the Flat Surface Mount Configuration Note: For wall mount installation, the L-bracket is not used.
Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 Placement and Other Important Considerations Before installing your wireless antenna, observe the placement considerations. Antenna placement dramatically affects potential coverage. Follow these guidelines to maximize coverage: • Place the ANT2409 in a vertical position. Either right side up or up-side-down is Ok. • Place the antenna in the middle of the coverage zone and at 1.5m or higher above the floor.
Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 • The best performance is achieved with a short cable between the antenna and the wireless device. The shortest approved cable to be used in conjunction with the ANT2409 in North America is the NETGEAR 1.5 m (ACC-10314-01) cable. • The antenna should be installed so that it is a minimum of 30 cm (12 inches) away from people.
Chapter 2 Installing the 9 dBi Omni-directional Antenna There are two parts to the wireless antenna installation process: • Assemble the wireless antenna for pole mount installation or flat surface mount installation. • Connect the appropriate electrical hardware depending on if the installation is indoors or outdoors. Follow the instructions in this section of the manual to install your antenna.
Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 First, Assemble and Mount the Antenna Step Step 1 Procedure Feed the antenna cable through the antenna mounting assembly. Note: Use the correct cable. • Outdoors: use the provided 2m antenna cable. • Indoors: use the provided N/SMA adapter with a Netgear cable model ACC-10314-01, 02, 03, 04 or 05 (sold separately). For indoors, do not use the provided 2m cable.
Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 Now, Connect the Antenna The instructions below cover outdoor and indoor installations. Connecting the Antenna for and Outdoor Installation 1. Turn off your wireless unit. 2. In the procedure “First, Assemble and Mount the Antenna” on page 2-2, the antenna should have been assembled for outdoor installation using the provided 2-meter cable. Connect the other side of the cable to the lighting arrestor as shown here.
Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 3. Connect the grounding cable (not included) from the lightning arrestor to the ground of the building. Grounding cable: The grounding cable must be equivalent or better than: AWG 10, UL 1015, Stranded, 600 V, 105 oC, green or green/yellow insulation, 2 clip of 5.5 mm inner diameter cramped at both ends, cable no longer than 5 meters. WARNING: the lightning arrestor and appropriate ground cable must be used for outdoor installation.
Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 Connecting the Antenna for an Indoor Installation 1. Turn off your wireless unit. 2. In the procedure “First, Assemble and Mount the Antenna” on page 2-2, the antenna should have been assembled for indoor installation using a NETGEAR cable ACC-10314-01, 02, 03, 04 or 05 and the reverse N/SMA adaptor connected to the antenna. The provided 2m cable should not have been used. D"I /MNI $IRECTIONAL !NTENNA !.4 !TTACH USING 2EVERSE .
Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 2-6 Installing the 9 dBi Omni-directional Antenna
Chapter 3 Specifications This chapter provides the 9 dBi Omni-directional Antenna specifications. 9 dBi Omni-directional Antenna and Mounting Assembly Specifications Usage OUTDOOR and INDOOR Frequency Range 2400 - 2485 MHz Type Omnidirectional Impedance 50 Ohms nominal SWR ≤ 2.0 Return Loss < -10 dB Gain 8.5 dBi Polarization Vertical Connector Type Reverse N Female Dimensions 22 mm (0.9 in) diameter, antenna element 610 mm (24 in) length Maximum volume Diameter: 44 mm (1.7 in) max.
Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 2 Meter Antenna Cable M CABLE Frequency Range VSWR Cable Type Transmission Loss Connector Type Max. Working Voltage Minimum Bend Radius Jacket Recommended coupling nut torque Coupling nut retention force Connector Body & Contact Insulation Storage, Transportation & Operating Temperature Storage, Transportation & Operating Humidity Waterproof UV 3-2 0 - 3 GHz 1.5 max. HPF195 Harbour Industries 2.2 dB max. @ 2.4 - 2.
Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 N/SMA Adaptor Accessory Specifications Frequency Range 0 - 3 GHz VSWR 1.5 max.
Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 Lightening Arrestor 3-4 Frequency Range 0 to 3 GHz VSWR 1.5 max. Insertion Loss 1.2 dB max. Impulse Breakdown Voltage 600 V min. (Voltage on upgrade ratio @100V/S) Max. Power Rating 200 W Impedance 50 ± 5 Ohm Insulation Resistance 1000 MOhm Max.
Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 Radiation Pattern: Elevation (Vertical plane) Specifications 3-5
Installation Guide for the 9 dBi Omni-directional Antenna ANT2409 Radiation Pattern: Azimuth (Horizontal plane) 3-6 Specifications