500mW Bi-directional Booster ANT24BNA Power Injector ANT24BDC Installation Guide
Introduction This section introduces the NETGEAR ANT24BNA 500 mW Bi-directional Booster and the NETGEAR ANT24BDC 6 VDC, 1.5A Power Injector and related components. The 500-milliwatt bi-directional power booster for the NETGEAR ME103 802.11b ProSafe Wireless Access Point increases the transmission signal from an average 50 mW to 500 mW and amplifies the signal by 10 dB (10 times) in receive mode. Use this when you want to maintain a single access point device to cover a larger area.
Power Injector Package Contents Installation Guide, Warranty card and Support information card Power Injector ANT24BDC The package should contain • NETGEAR 6 VDC 1.5A Power Injector ANT24BDC for bi-directional booster ANT24BNA • Installation Guide • Warranty card • Support information card If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the carton, including the original packing materials, in case you need to return the product for repair.
One Antenna Port, One Booster and One Antenna Two Antenna Ports, Two Boosters and Two Antennas DC Block DC Block Antenna e. g. NETGEAR ANT24O5 Antenna e. g.
Installing the Booster with the Optional Power Injector Specifications Note: As noted in the illustration below, be sure to disconnect the DC power adapter from the ANT24BNA Booster for 802.11b, and connect it to the NETGEAR ANT24BDC Power Injector. Current antenna Do NOT remove Connect Antenna cable NETGEAR Antenna cable (short or medium) Antenna e. g.
Description NETGEAR 500mW Bi-directional Booster for 802.11b, with Two Female Reverse SMA Connectors RF Connector Recommended Coupling Nut Torque 0.45 to 0.99 Nm (4.0 to 8.8 in.lb.) RF Connector Coupling Nut Retention Force 22.7 kg (50 lb) min. RF Connector Contact Captivation Axial 2.27 kg (5 lb) min.
Specifications ANT24BDC Power Injector for the ANT24BNA Booster with Two Female Reverse SMA Connectors Description ANT24BDC Power Injector for the ANT24BNA Booster with Two Female Reverse SMA Connectors Operation Temperature 0 to 70° C (32 to 158° F) Frequency Range 2400 to 2500 MHz Storage Temperature -10 to 80° C (14 to 176° F) PTC Fuse 2.5 A / 30 V Humidity 10% to 90% Insertion Loss 1.5 dB maximum @ 2.4 to 2.5 GHz Device Size (l x w x h) 88.2 x 58.9 x 33.4 mm (3.48 x 2.32 x 1.
Statement of Conditions In the internal function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Technical Support PLEASE REFER TO THE SUPPORT INFORMATION CARD THAT SHIPPED WITH YOUR PRODUCT. By registering your product at www.NETGEAR.com/register, we can provide you with faster expert technical support and timely notices of product and software upgrades. NETGEAR, INC. Support Information Phone: 1-888-NETGEAR (For US & Canada only) - 24x7 phone support See Support Information card for other countries. E-mail: support@NETGEAR.com (24x7 online support) www.NETGEAR.com ©2003 NETGEAR, Inc.