Technical Support Package Contents Thank you for selecting NETGEAR products. The box should contain the following items. If any items are incorrect, missing, or damaged, contact your NETGEAR dealer. N600 Wireless Dual Band Gigabit ADSL2+ Modem Router DGND3700v2 Installation Guide ADSL Phone Go to support.netgear.com for product updates and web support. Line After installing your device, locate the serial number on the label of your product and use it to register your product at NETGEAR.com/register.
Compliance You can use this diagram to connect your modem router to ADSL (1a) or Cable/Fiber (1b), or you can follow the instructions in this booklet. 1a: For ADSL Internet Declarations of Conformity For complete DoC please visit the NETGEAR EU Declarations of Conformity website at: support.netgear.com/app/answers/detail/a_id/11621/. For GNU General Public License (GPL) related information, please visit support.netgear.com/app/answers/detail/a_id/2649.
Contents Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Install Your Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Preset Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Wireless Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Add Wireless Devices to the Network . . . . . . . . . . . . . . . . . . . 10 WPS Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before You Begin You can connect directly to a DSL line or to a fiber/cable modem. Note: If you are connecting to a DSL line, make sure that your DSL service is active before you install the modem router. You need the information listed here to install your DSL modem and connect to the Internet. Please locate it and have it on hand before you start the installation procedure. • DSL user name and password.
DSL Internet Service Provider Phone Number AT&T DSL (not AT&T U-Verse) 877-722-3755 AT&T/BellSouth DSL (not AT&T U-Verse) 888-321-2375 CenturyLink 800-809-1410 Covad DSL 888-642-6823 EarthLink 888-829-8466 Qwest 800-247-7285 SureWest 888-639-1611 TDS DSL Support 866-571-6662 US Family 800-300-4256 Verizon 800-567-6789 Windstream 877-901-4692 3
Install Your Modem Router Note: Keep your modem router in a vertical position. To install your modem router: 1. Connect to the Internet with ADSL or Ethernet WAN. You can connect either directly to a DSL line or to a fiber/cable modem. a. Connect to ADSL (if connecting directly to a DSL line). Internet 1 • Install an ADSL microfilter between the phone line and the phone. A microfilter filters DSL interference out of standard phone equipment that shares the same line with DSL service.
Note: Use an ADSL microfilter for every phone line in the house if your modem router and telephone connect to the same phone line. Plugs into ADSL line b. Connect to Cable/Fiber (if connecting to a cable/fiber modem). 1 Internet Cable/Fiber Modem 2. Cable your computer. Use an Ethernet cable (not provided).
3. Power on your router. Internet 3 Internet 2.4 GHz Wi l Wireless LED a. Connect the power adapter to the router, and plug the power adapter into an outlet. b. Wait until the 2.4 GHz Wireless LED green. 4. Open a browser. If a web page does not open, close and reopen the browser, and enter http://routerlogin.net in the address bar. See Troubleshooting on page 13. turns solid 4 Enter the router user name admin and default password password. Click OK.
5. Connect to the Internet. Select Advanced > Setup Wizard to display the Setup Wizard screen. Make sure Yes is selected. Then click Next and follow the prompts to complete the Setup Wizard and be connected to the Internet. Note for DSL users: If your DSL ISP requires that you enter a user name or password, you are prompted to enter this information. If you do not have this information, contact your DSL ISP (for more information, see Before You Begin on page 2). 6.
Preset Wireless Security This product has a unique WiFi network name (SSID) and network key (password). The default SSID and network key (password) are uniquely generated for every device, like a serial number, to protect and maximize your wireless security. This information is located on the label on the bottom of the product. WiFi Network Name (SSID) Network Key (Password) NETGEAR recommends that you do not change the preset WiFi network name (SSID) and network key (password).
Wireless Network Settings Record the default preset wireless settings that are printed on the label in the spaces here for easy reference. 2.4 GHz WiFi network name (SSID): 2.4 GHz network key (password): 5 GHz WiFi network name (SSID): 5 GHz network key (password): If you change the default settings, record them here for easy reference, and then store this booklet in a safe place: 2.4 GHz WiFi network name (SSID): 2.
Add Wireless Devices to the Network Choose either the manual or Wi-Fi Protected Setup (WPS) method to add wireless computers and other devices to your wireless network. WPS Method If your wireless device supports WPS (Wi-Fi Protected Setup)— NETGEAR calls this method Push 'N' Connect—you might be prompted to press the WPS button on the router instead of entering a password. If this happens: 1. Press the WPS button on the router. 2.
Repeat steps 1–3 to add other wireless devices. Access the N600 Router to Make Changes After you use NETGEAR Genie to set up the router, you can log in to the router to view its settings or make changes. To log in to the router: 1. Launch a web browser from a computer or wireless device that is connected to the router. 2. Type www.routerlogin.net or www.routerlogin.com in the address field of the browser. A login screen displays: 3. Enter admin for the user name and password for the password.
See the User Manual for more information about the router screens. To change the password for the router user name: 1. Log in to the router. 2. Select Advanced > Administration > Set Password to display the Set Password screen: 3. Type your old password, and type the new password twice.
Troubleshooting If the browser does not display the web page: • Make sure that the computer is connected to one of the four LAN Ethernet ports, or wirelessly to the router. • Make sure that the router is fully up and running. Its WiFi LED should turn on. • Close and reopen the browser to make sure that the browser does not cache the previous page. • Browse to http://routerlogin.net.
e. Turn your computer back on, and wait for the indicator lights to turn green. 3. Open a web browser and try to access the Internet. If steps 1–3 do not resolve the problem: 4. Reset your modem. To reset your DSL modem router, use a pin or paper clip to press in and hold the Reset button.
ReadySHARE Access After installation and set-up, you can insert a USB storage device into the USB port on the modem router and share the contents with other network users. (If your USB device has special drivers, it is not compatible.) Note: If your USB device requires a power supply, you have to use it when connecting your USB device to a NETGEAR router or gateway. It might take up to 2 minutes before the USB drive is ready for sharing after it is connected to the router.
The readyshareconnect.exe file (for Windows) is available to download here: www.netgear.
USB Control Center The USB Control Center utility allows you to control a shared USB device from your computer that is connected to the USB port on your router. The utility allows you to control a printer. The utility has to be installed on each computer on your network from which you want to control the device. You can download this utility at www.netgear.com/landing/en-us/readyshare.aspx.
The following menu selections are available: • System. Exit the utility. • Tools. Access the Control Center Configuration to set up your shared USB device. See the following section, Control Center Configuration. • About. View details about the USB Control Center software. Control Center Configuration Select Tools > Configuration to display the following screen: Automatically execute when logging on Windows.
Language. Select the display language for this utility. USB Printer The first time you use a printer, you need to click Connect. You might be asked to install the driver for this printer. After the driver is installed, the printer status changes to Available. Note: Some USB printers (for example: HP and Lexmark printer) request that you do not connect the USB cable until you are prompted by the installation software.
prints. After the print job is done, the printer status returns to the Paused state. Scan with a Multifunction Printer You can use the scan feature of a multifunction printer. 1. Make sure that the printer’s status shows as Available. 2. Click the Network Scanner button. This activates the scanner window that is used to perform the scans. USB Speaker To control a USB speaker: 1. Select the USB speaker. 2. Click the Connect button to connect this speaker, or click Disconnect to disconnect the speaker.
Other Features For additional features, including Live Parental Controls, Traffic Metering, ReadySHARE, Guest Access, and more, please log into your router at http://routerlogin.net. © 2012 NETGEAR, Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the written permission of NETGEAR, Inc. DO NOT stack equipment, or place equipment in tight spaces or in drawers.
