Quick Start N300 WiFi Range Extender Model EX2700
Getting Started The NETGEAR WiFi Range Extender increases the distance of a WiFi network by boosting the existing WiFi signal and enhancing the overall signal quality over long distances. An extender repeats the signals from an existing WiFi router or access point. WiFi Range Extender Boosts the range of your existing WiFi and creates a stronger signal in hard-to-reach areas. Existing WiFi Sometimes your router does not provide the WiFi coverage you need.
Meet Your Extender Before you install your extender, familiarize yourself with its LEDs, buttons, and port.
LED Descriptions Router Link LED This LED indicates the connection between the extender and the router or access point. Solid green. Best connection. Solid amber. Good connection. Solid red. Poor connection. Off. No connection. Device Link LED This LED indicates the connection between the extender and a computer or mobile device. Solid green. Best connection. Solid amber. Good connection. Solid red. Poor connection. Off. No connection. Power LED Solid amber. The extender is booting. Solid green.
Use the Extender The extender repeats the signals from an existing WiFi router or access point. Place the extender, supply power, and connect it to your WiFi network. Place the Extender and Supply Power 1. Place your extender in the same room as your WiFi router. Proximity to the WiFi router is required only during the initial setup process. 2. Plug the extender into an electrical outlet. Wait for the Power LED to light green. 3.
Connect to an Existing WiFi Network To extend the range of your WiFi network, you must connect the extender to your existing WiFi network. You can do this in one of two ways: • • Connect with WPS. For more information, see Connect with WPS on page 6. Connect with the NETGEAR installation assistant. For more information, see Connect with the NETGEAR Installation Assistant on page 10.
2. Within two minutes, press the WPS button on your router or access point. When the extender connects to your existing WiFi network, the WPS LED on the extender lights solid green and the Router Link LED lights. If the Router Link LED does not light, try again. If it still does not light, see Connect with the NETGEAR Installation Assistant on page 10. 3. Unplug the extender and move it to a new location that is about halfway between your router and the area with a poor router WiFi signal.
7. On your computer or WiFi device, find and connect to the new extended WiFi network. The extender creates a new extended WiFi network. The extender’s new WiFi network name is based on your existing WiFi network name, with _EXT at the end of the name. For example: • Existing WiFi network name. MyNetworkName • New extended WiFi network name. MyNetworkName_EXT. Use the same WiFi password that you use for your WiFi router.
8. Test the extended WiFi range by moving your computer or WiFi device to the area with a poor router WiFi signal: a. Leave your computer or WiFi device in the area with a poor router WiFi signal and return to the extender. b. Check the Device Link LED on the extender: • If the Device Link LED is solid green or amber, your extended WiFi network reaches the area with a poor router WiFi signal and your network setup is complete.
Connect with the NETGEAR Installation Assistant 1. Use a WiFi network manager on a computer or mobile device to find and connect to the extender WiFi network NETGEAR_EXT. After the connection with the computer or WiFi device is established, the Device Link LED lights. 2. Launch a web browser. 3. Enter www.mywifiext.net in the address field of the browser. The New Extender Setup page displays. 4. Click the NEW EXTENDER SETUP button. The Create Account page displays. 5.
8. Set the network name (SSID) and password for your extender and click the NEXT button. Note: We recommend that you use a different network name (SSID) for your extender than the network name (SSID) that your router uses. Wait for the page to display the new extended WiFi network settings, which might take up to one minute. 9. Connect your computer or WiFi device to the new extended WiFi network using the SSID and password that you created in Steps 7 and 8. 10.
13. Complete the registration fields and click the FINISH button to complete the setup. If you do not want to register your extender, click the Skip Registration link. Note that you must register your extender before you can use NETGEAR telephone support. The Status page displays. 14. Unplug the extender and move it to a new location that is about halfway between your router and the area with a poor router WiFi signal.
17. If the Router Link LED doesn’t light amber or green, plug the extender into an outlet closer to the router and try again. Keep moving the extender to outlets closer to the router until the Router Link LED lights amber or green. 18. Reconnect your computer or WiFi device to the new extended WiFi network. 19. Test the extended WiFi range by moving your computer or WiFi device to the area with a poor router WiFi signal: a.
Connect an Ethernet-Enabled Device After the extender is connected to your existing WiFi network, you can connect a wired device to the extender using an Ethernet cable. That device can then access your existing network through the WiFi connection.
Access Extender Settings After installation, you can log in to the extender to view or change the extender’s settings. 1. Use a WiFi network manager on a computer or WiFi device to find and connect to the new extended WiFi network. After the connection with the computer or WiFi device is established, the Device Link LED lights. 2. Launch a web browser. 3. Enter www.mywifiext.net in the address field of the browser. A login window opens. 4.
Frequently Asked Questions You can find more information about your product in the user manual, which is available at http://downloadcenter.netgear.com. I forgot my login email address and password. What can I do? In the login window, click the Username & Password Help link to answer the security questions that you set up during the initial setup. If you forgot the answers to your security questions, do the following to set up your login credentials again: 1.
The web browser setup guide keeps asking me for my network password (passphrase) or security key, and I am sure I have entered the correct password. What can I do? The extender is probably placed at the borderline of the range covered by the router or access point. For more information, see Place the Extender and Supply Power on page 5. If you are using WEP security, make sure that you are typing the network password in the correct field.
How do I restore the extender to its factory default settings? 1. Use a sharp object such as a pen or straightened paper clip to press and hold the Factory Reset button on the extender for at least five seconds until the Power LED lights amber. 2. Release the Factory Reset button and wait for the extender to reboot. The extender resets and returns to the factory default settings. I enabled a wireless MAC filter, wireless access control, or access control list (ACL) on my router.
2. Power on the extender and connect all of your WiFi devices to the extender network. 3. Make sure that the Router Link LED remains lit. 4. Log in to your extender: a. Launch a web browser. b. Enter www.mywifiext.net in the address field of the browser. A login window opens. c. Enter your email address and password and click the LOG IN button. The Status page displays. 5. Select Settings > Connected Devices.
Support Thank you for purchasing this NETGEAR product. You can visit www.netgear.com/support to register your product, get help, access the latest downloads and user manuals, and join our community. We recommend that you use only official NETGEAR support resources. Trademarks © NETGEAR, Inc., NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non‑NETGEAR trademarks are used for reference purposes only. Compliance For the current EU Declaration of Conformity, visit: http://support.netgear.
