User's Manual

ManualsBrandsNetgear ManualsElectronicsWIRELESS FIREWALL

Table Of Contents

Instructions for the installation of Detachable Antenna with the FWG114P

Instructions for the installation of Detachable Antenna with

the FWG114P

1. Introduction

This information provides guidelines to permit you to install the NETGEAR detachable antennas with

the FWG114P 11g wireless router and antenna cable and be compliant with the FCC regulations.

FWG114P provides 15dBm maximum transmit power plus antenna gain.

The maximum equivalent isotropic radiated power limit is 1W ERP. When installing the detachable

antennas listed below, the installer has to be sure the limits won’t be exceeded. If so, attenuation in the

form of antenna cable is added between the FWG114P wireless node and the antenna.

It is not allowed to let the end user do whatever they want. Anyone tries to use non-

Netgear dedicated accessory may have violated the regulation and voided the right to use.

If they use Netgear's antenna accessories, they are all well prepared. The cables and

connectors are matched.

Disclaimer: Use of any antenna requires careful planning and extra consideration to comply with

emissions and health standards and regulations. It is recommended that a qualified professional

installer service is consulted for site survey and proper installation. Antenna installation must comply

with the maximum level authorized by each country.

2. NETGEAR Antenna Cable Attenuation at 2.4- 2.5 GHz

NETGEAR Cable Type Length Typical Attenuation at 2.4 - 2.5 GHz

ACC-10314-01 1.5 m

1.1 dB

ACC-10314-02 3 m

2.0 dB

ACC-10314-03 5 m

3.2 dB

ACC-10314-04 10 m

6.1 dB

ACC-10314-05 30 m

18.0 dB

3. Installation Procedure for the Wireless Node, Antenna Cable, and Antenna

1. In the table below, identify the NETGEAR detachable antenna to be used with the

FWG114P, e.g. the ANT24D18.

2. Read the required NETGEAR Antenna cable to be used, e.g. ACC-10314-05 30m cable

(with ANT24D18). In some cases, no cable is required. Therefore in this situation, the

user is free to use a NETGEAR cable from 1.5m to 30m or no cable at all.

3. Connect the selected antenna cable to the FWG114P wireless Node and to the antenna

Antenna list: Mandatory antenna cable to be used with each antenna

and FWG114P

NETGEAR

Antenna

Manufacturer P/N Antenna Type Antenna

max.

Gain

Theoretical

EIRP without

cable

MINIMUM

Cable

Attenuation

needed

cabl

MIN

Summary of content (3 pages)

PAGE 1
Instructions for the installation of Detachable Antenna with the FWG114P 1. Introduction This information provides guidelines to permit you to install the NETGEAR detachable antennas with the FWG114P 11g wireless router and antenna cable and be compliant with the FCC regulations. FWG114P provides 15dBm maximum transmit power plus antenna gain. The maximum equivalent isotropic radiated power limit is 1W ERP.
PAGE 2
LEN ANT24P2 TBC* JOYMAX IW-144 Omnidirection al 2dBi 17 dBm EIRP 0 dB 0m ANT24P3 TBC* ANTENNIQUES MCS-003A Omnidirection al 3dBi 18 dBm EIRP 0 dB 0m ANT24P4 TBC* JOYMAX IW152RS Omnidirection al 4dBi 19 dBm EIRP 0 dB 0m ANT24S4 TBC* SENAO NAST0405(N) Omnidirection al Triband Stand 4dBi 19 dBm EIRP 0 dB 0m ANT24P5 TBC* ANTENNIQUES MCS-004 Omnidirection al 5dBi 20 dBm EIRP 0 dB 0m ANT24S5 TBC* SENAO NAS2405(N) Omnidirection al Stand 5dBi 20 dBm EIRP 0 dB 0m ANT24P7 TB
PAGE 3
Disclaimer: NETGEAR assumes no responsibility in case of intentional or unintentional violation of the maximum allowable EIRP/ERP in a particular country, miscalculation of the attenuation, faulty nonNETGEAR wireless node, or bad connection from antenna to wireless node.