GS110TP Hardware Installation Guide NETGEAR, Inc. 350 East Plumeria Drive San Jose, California 95134 USA 202-10596-01 March 2010 v1.
© 2010 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR, the NETGEAR logo, and Auto Uplink are trademarks or registered trademarks of NETGEAR, Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Other brand and product names are registered trademarks or trademarks of their respective holders. Portions of this document are copyright Intoto, Inc.
Contents GS110TP Hardware Installation Guide About This Manual Conventions, Formats, and Scope .................................................................................... v How to Print this Manual ................................................................................................... vi Revision History ................................................................................................................ vi Chapter 1 Introduction Overview ....................................
Chapter 4 Installation Step 1: Preparing the Site ..............................................................................................4-1 Step 2: Installing the Switch ...........................................................................................4-2 Installing the Switch on a Flat Surface .....................................................................4-2 Wall Mounting the Switch .........................................................................................
About This Manual The NETGEAR® ProSafeTM GS110TP Hardware Installation Guide describes how to install and power on the GS110TP Smart PoE Switch. The information in this manual is intended for readers with intermediate computer and Internet skills. Conventions, Formats, and Scope The conventions, formats, and scope of this manual are described in the following paragraphs: • • Typographical Conventions.
GS110TP Hardware Installation Guide Danger: This is a safety warning. Failure to take heed of this notice may result in personal injury or death. • Scope. This manual is written for the GS110TP Smart PoE Switch according to these specifications: Product Version GS110TP Smart PoE Switch Manual Publication Date March 2010 Note: Product updates are available on the NETGEAR, Inc. website at http://kbserver.netgear.com/products/GS110TP.asp.
Chapter 1 Introduction Congratulations on the purchase of your NETGEAR GS110TP Smart PoE Switch. The GS110TP Smart PoE Switch is a supplement to the Gigabit Advanced Smart Switch family. Available as a desktop or wall-mountable switch, the GS110TP Smart PoE Switch is not intended to be rackmountable. The GS110TP is a PoE-supportable, low-port switch with two fiber uplinks included.
GS110TP Hardware Installation Guide The GS110TP Smart PoE Switch is a free-standing switch. It is IEEE-compliant and offers low latency for high-speed networking. All ports can automatically negotiate to the highest speed. This capability makes the switch ideal for environments that have a mix of Ethernet, Fast Ethernet, or Gigabit Ethernet devices. In addition, all RJ-45 ports operate in half-duplex or full-duplex mode.
GS110TP Hardware Installation Guide • Standard NETGEAR 1xx series chassis. • NETGEAR Green product features. • External 48V/1.25A PA. PoE Features The GS110TP Smart PoE Switch supports IEEE 802.3af PSE features: • Ports 1 through 8 support IEEE 802.3af, Alternative A (MDI-X). • PoE is enabled by default. Green Features The GS110TP Smart PoE Switch supports the following power-saving features: • The power consumption automatically adjusts based on the RJ-45 cable length.
GS110TP Hardware Installation Guide Package Contents Figure 1-1 shows the package contents of the NETGEAR GS110TP Smart PoE Switch.
Chapter 2 Physical Description This chapter describes the NETGEAR GS110TP Smart PoE Switch hardware features. Topics include: • GS110TP Front and Back Panel Configuration • LED Designations • Device Hardware Interfaces GS110TP Front and Back Panel Configuration The GS110TP Smart PoE Switch has eight 10/100/1000 Mbps autosensing and two 1000 Mbps SFP Gigabit Ethernet switching ports.
GS110TP Hardware Installation Guide • Power and Status LED • PoE Max LED Figure 2-2 illustrates the NETGEAR GS110TP Smart PoE Switch back panel. Power Connector Figure 2-2 The back panel contains the following: • A DC input for the supplied 48V/1.25A external power adapter LED Designations Port LEDs The following table describes the RJ-45 and SFP port LED designations. There are two LEDs for each RJ-45 port. Each SFP port has its own indication LED. Table 2-1.
GS110TP Hardware Installation Guide Table 2-1. Port LEDs (continued) LED Designation PoE Status (Right LED on each RJ-45 port) • Off = No PoE powered device (PD) connected. • Solid Green = The PoE PD is connected and the port is supplying power successfully. • Flashing Yellow = One of the following failures resulted in stopping power to that port: – Short circuit on PoE power circuit. – PoE power demand exceeds power available. – PoE current exceeds PD's classification.
GS110TP Hardware Installation Guide To simplify the procedure for attaching devices, all RJ-45 ports support Auto Uplink. This technology allows attaching devices to the RJ-45 ports with either straight-through or crossover cables. When inserting a cable into the switch’s RJ-45 port, the switch automatically: • Senses whether the cable is a straight-through or crossover cable.
Chapter 3 Applications Your NETGEAR GS110TP Smart PoE Switch is designed to provide flexibility in configuring your network connections. It can be used as a stand-alone device or with 10 Mbps, 100 Mbps, and 1000 Mbps hubs and switches. Desktop Switching The GS110TP Smart PoE Switch can be used as a desktop switch to build a small network that enables users to have 1000 Mbps access to a file server. With full-duplex enabled, the switch port connected to the server or PC can provide 2000 Mbps throughput.
GS110TP Hardware Installation Guide 3-2 Applications v1.
Chapter 4 Installation This chapter describes the installation procedures for your NETGEAR GS110TP Smart PoE Switch.
GS110TP Hardware Installation Guide Table 4-1. Site Requirements (continued) Characteristics Requirements Power source Provide a power adapter (included). Power specifications for the switch are shown in Appendix A . Ensure the AC outlet is not controlled by a wall switch, which can accidentally turn off power to the outlet and the switch. Environmental • Temperature - Install the switch in a dry area, with ambient temperature between 0 and 50ºC (32 and 122ºF).
GS110TP Hardware Installation Guide Step 3: Checking the Installation Before applying power to the switch, perform the following: • Inspect the equipment thoroughly. • Verify that all cables are installed correctly. • Check cable routing to make sure cables are not damaged or creating a safety hazard. • Ensure all equipment is mounted properly and securely. Step 4: Connecting Devices to the Switch The following procedure describes how to connect PCs to the switch’s RJ-45 ports.
GS110TP Hardware Installation Guide Connect each PC to an RJ-45 network port on the Switch front panel (Figure 4-1 ). Use Category 5 (Cat5) Unshielded Twisted-Pair (UTP) cable terminated with an RJ-45 connector to make these connections. Note: Ethernet specifications limit the cable length between the switch and the attached device to 100 m (328 ft.).
GS110TP Hardware Installation Guide Note: When the device powers up, there is a default IP address already configured on the device. The default IP address is 192.168.0.239 and subnet mask 255.255.255.0. Installation 4-5 v1.
GS110TP Hardware Installation Guide 4-6 Installation v1.
Appendix A Troubleshooting This chapter provides information about troubleshooting the NETGEAR Smart Switch. Topics include the following: • Troubleshooting Chart • Additional Troubleshooting Suggestions Troubleshooting Chart The following table lists symptoms, causes, and solutions of possible problems. Table A-1. Troubleshooting Chart Symptom Cause Solution Power LED is off. No power is received. Check the power cord connections, the ON/OFF switch, and the connected device.
GS110TP Hardware Installation Guide Table A-1. Troubleshooting Chart Symptom Cause Solution A segment or device is One or more devices are not recognized as part of not properly connected, the network. or cabling does not meet Ethernet guidelines. Verify that the cabling is correct. Ensure all connectors are securely positioned in the required ports. Equipment may have been accidentally disconnected. ACT LED is flashing continuously on all connected ports and the network is disabled.
GS110TP Hardware Installation Guide Auto-Negotiation The RJ-45 ports negotiate the correct duplex mode and speed if the device at the other end of the link supports auto negotiation. If the device does not support auto negotiation, the switch only determines the speed correctly and the duplex mode defaults to half-duplex. The gigabit port on the Gigabit module negotiates speed, duplex mode, and flow control, provided that the attached device supports auto-negotiation. Troubleshooting A-3 v1.
GS110TP Hardware Installation Guide A-4 Troubleshooting v1.
Appendix B Technical Specifications Network Protocol and Standards Compatibility IEEE 802.3i 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3x flow control IEEE 802.3z 1000BASE-X IEEE 802.3af DTE Power via MDI Management Windows 2000 + XP, Vista; Microsoft Explorer 6.0 or higher IEEE 802.1Q VLAN IEEE 802.3ad Link Aggregation IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1X Port Security IEEE 802.
GS110TP Hardware Installation Guide Interface Eight RJ-45 connectors for 10BASE-T, 100BASE-TX, and 1000BASE-T (Auto Uplink™ on all ports) Two SFP slots for SFP modules LEDs Per RJ-45 port: Speed/Link/Activity Per SFP port: SFP indicator Performance Specifications Forwarding modes: Store-and-forward Bandwidth: 20 Gbps Address database size: 4K media access control (MAC) addresses per system Mean Time Between Failure (MTBF): 157,004 hours Power Supply 48V/1.
GS110TP Hardware Installation Guide Electromagnetic Emissions FCC Class B CE Class B: Includes EN55022 (CISPR 22), 55024, and 50082-1 VCCI Class B C-Tick Safety UL/cUL (UL 1950)/cUL IEC950/EN60950) CE (includes EN60950) IEC950 CB Technical Specifications B-3 v1.
GS110TP Hardware Installation Guide B-4 Technical Specifications v1.
Index Numerics F 1U 1-3 Factory Default Button 2-4 8-pin 2-3 Factory Defaults 2-1 Flat Surface 4-2 A Full-duplex 1-2 Applying AC Power 4-4 Auto Uplink 2-4 G Auto-negotiating 1-2 Gigabit Ports 1-1 Autosensing 1-2, 2-3 H B High-speed Servers 1-1 Backpressure 1-2 I C IEEE 802.3i 1-2 Category 5 Unshielded Twisted-Pair 1-2 IEEE 802.
GS110TP Hardware Installation Guide O V Operating Conditions 4-2 Ventilation 4-2 Operating Environment 4-1 VLAN 1-1 Operating humidity 4-2 Overview 1-1 W Web-based Graphical User Interface 1-1 P Package Contents 1-4 Pause Frame Flow Control 1-2 Port LEDs 2-2 Power cord 1-4 Preparing the Site 4-1 R Rack-mount Kit 1-4 Reset Button 2-1 RJ-45 1-2 RJ-45 Ports 2-2 Rubber footpads 1-4, 4-2 S Site Requirements 4-1 Smart Switch Resource CD 1-4 Straight-through 2-4 System LEDs 2-3 T Temperature 4-2 Traffi
