User Manual
Table Of Contents
- M4100 Series Managed Switch
- Contents
- 1. Get Started
- 2. Configure System Information
- System Configuration
- Configure Initial Management VLAN Settings
- Define System Information
- View the Switch Status
- Manage Loopback Interfaces
- View the IPv6 Network Neighbor Table
- Configure an IPv4 Management VLAN
- View or Set the System Time
- Configure DNS
- Configure the DHCP Server
- Configure the DHCP Pool
- Configure UDP Relay Global Settings
- Configure the Basic PoE Settings
- Configure Advanced PoE Settings
- View All MIBs Supported by the Switch
- Configure SNMP v3 Settings for a User
- LLDP Overview
- Configure LLDP Global Settings
- Configure an LLDP Interface
- View LLDP Statistics
- View LLDP Local Device Information
- View LLDP Remote Device Information
- View LLDP Remote Device Inventory
- Configure LLDP-MED Global Settings
- Configure the LLDP-MED Interface
- View LLDP-MED Local Device Information
- View LLDP-MED Remote Device Information
- View LLDP-MED Remote Device Inventory
- ISDP Settings Overview
- Configure Timers
- 3. Configure Switching Information
- VLAN Overview
- Configure a Basic VLAN
- Configure an Internal VLAN
- Add a VLAN
- Reset VLAN Configuration
- Configure Internal VLAN Settings
- Configure VLAN Trunking
- Configure VLAN Membership
- View VLAN Status
- Configure Port PVID
- Configure a MAC-Based VLAN Group
- Configure a Protocol-Based VLAN Group
- Configure Protocol-Based VLAN Group Membership
- Configure an IP Subnet–Based VLAN
- Configure Port DVLAN
- Configure a Voice VLAN
- Configure GARP Switch Settings
- Configure GARP Port Settings
- Auto-VoIP Overview
- Spanning Tree Protocol Overview
- Configure Multicast
- IGMP Snooping Overview
- Configure MLD Snooping
- Configure MVR
- Manage MAC Addresses
- Configure Port Settings
- Link Aggregation Group Overview
- VLAN Overview
- 4. Routing
- 5. Configure Quality of Service
- QoS Overview
- Class of Service
- Differentiated Services
- DiffServ Wizard Overview
- Use the DiffServ Wizard
- Configure DiffServ
- Configure the Global Diffserv Mode
- Configure a DiffServ Class
- Configure the Class Match Criteria
- Configure a DiffServ IPv6 Class
- Configure the DiffServ Class Match Criteria
- Configure DiffServ Policy
- Configure DiffServ Policy Attributes
- Configure DiffServ Policy Settings on an Interface
- View Service Statistics
- 6. Manage Device Security
- Management Security Settings
- Configure RADIUS Settings
- TACACS
- Set Up a Login Authentication List
- Configure Management Access
- Manage Certificates
- Manage Telnet
- Port Authentication Overview
- Traffic Control
- Configure a Private Group
- Private VLAN Overview
- Storm Control Overview
- Control DHCP Snooping Settings
- Configure an IP Source Guard Interface
- Configure Dynamic ARP Inspection
- Access Control List Overview
- Use the ACL Wizard
- Create a MAC ACL
- Configure MAC Rules
- Configure ACL MAC Binding
- View or Delete MAC Bindings
- Configure an IP ACL
- Configure Rules for an IP ACL
- Configure IP Extended Rules
- Configure an IPv6 ACL
- Configure IPv6 Rules
- Configure ACL Interface Bindings
- View or Delete IP ACL Bindings
- View or Delete VLAN ACL Bindings
- 7. Monitoring the System
- 8. Maintenance
- A. Default Settings
- B. Configuration Examples
Routing
218
M4100 Series Managed Switch
IpInDiscards The number of input IP datagrams for which no problems were
encountered to prevent their continued processing, but that were
discarded (such as for lack of buffer space). Note that this counter does
not include any datagrams discarded while awaiting reassembly.
IpInDelivers The total number of input datagrams successfully delivered to IP user
protocols (including ICMP).
IpOutRequests The total number of IP datagrams that local IP user protocols (including
ICMP) supplied to IP in requests for transmission.This counter does not
include any datagrams counted in ipForwDatagrams.
IpOutDiscards The number of output IP datagrams for which no problem was
encountered to prevent their transmission to their destination, but that
were discarded (such as for lack of buffer space). Note that this counter
would include datagrams counted in ipForwDatagrams if any such
packets met this (discretionary) discard criterion.
IpOutNoRoutes The number of IP datagrams discarded because no route could be
found to transmit them to their destination. Note that this counter
includes any packets counted in ipForwDatagrams that meet this
`no-route' criterion. Note that this includes any datagrams that a host
cannot route because all of its default gateways are down.
IpReasmTimeout The maximum number of seconds that received fragments are held
while they are awaiting reassembly at this entity.
IpReasmReqds The number of IP fragments received that needed to be reassembled at
this entity.
IpReasmOKs The number of IP datagrams successfully re-assembled.
IpReasmFails The number of failures detected by the IP re-assembly algorithm (for
whatever reason: timed out, errors, and so on). This is not necessarily
a count of discarded IP fragments since some algorithms can lose track
of the number of fragments by combining them as they are received.
IpFragOKs The number of IP datagrams that were successfully fragmented at this
entity.
IpFragFails The number of IP datagrams that were discarded because they needed
to be fragmented at this entity but could not be, such as because their
Don't Fragment flag was set.
IpFragCreates The number of IP datagram fragments that were generated as a result
of fragmentation at this entity.
IpRoutingDiscards The number of routing entries that were discarded even though they
are valid. One possible reason for discarding such an entry could be to
free up buffer space for other routing entries.
IcmpInMsgs The total number of ICMP messages that the entity received. Note that
this counter includes all those counted by icmpInErrors.
Table 68. IP statistics (continued)
Field Description