User Manual
Table Of Contents
- M4100 Series Managed Switch
- Contents
- 1. Get Started
- 2. Configure System Information
- System Configuration
- Configure Initial Management VLAN Settings
- Define System Information
- View the Switch Status
- Manage Loopback Interfaces
- View the IPv6 Network Neighbor Table
- Configure an IPv4 Management VLAN
- View or Set the System Time
- Configure DNS
- Configure the DHCP Server
- Configure the DHCP Pool
- Configure UDP Relay Global Settings
- Configure the Basic PoE Settings
- Configure Advanced PoE Settings
- View All MIBs Supported by the Switch
- Configure SNMP v3 Settings for a User
- LLDP Overview
- Configure LLDP Global Settings
- Configure an LLDP Interface
- View LLDP Statistics
- View LLDP Local Device Information
- View LLDP Remote Device Information
- View LLDP Remote Device Inventory
- Configure LLDP-MED Global Settings
- Configure the LLDP-MED Interface
- View LLDP-MED Local Device Information
- View LLDP-MED Remote Device Information
- View LLDP-MED Remote Device Inventory
- ISDP Settings Overview
- Configure Timers
- 3. Configure Switching Information
- VLAN Overview
- Configure a Basic VLAN
- Configure an Internal VLAN
- Add a VLAN
- Reset VLAN Configuration
- Configure Internal VLAN Settings
- Configure VLAN Trunking
- Configure VLAN Membership
- View VLAN Status
- Configure Port PVID
- Configure a MAC-Based VLAN Group
- Configure a Protocol-Based VLAN Group
- Configure Protocol-Based VLAN Group Membership
- Configure an IP Subnet–Based VLAN
- Configure Port DVLAN
- Configure a Voice VLAN
- Configure GARP Switch Settings
- Configure GARP Port Settings
- Auto-VoIP Overview
- Spanning Tree Protocol Overview
- Configure Multicast
- IGMP Snooping Overview
- Configure MLD Snooping
- Configure MVR
- Manage MAC Addresses
- Configure Port Settings
- Link Aggregation Group Overview
- VLAN Overview
- 4. Routing
- 5. Configure Quality of Service
- QoS Overview
- Class of Service
- Differentiated Services
- DiffServ Wizard Overview
- Use the DiffServ Wizard
- Configure DiffServ
- Configure the Global Diffserv Mode
- Configure a DiffServ Class
- Configure the Class Match Criteria
- Configure a DiffServ IPv6 Class
- Configure the DiffServ Class Match Criteria
- Configure DiffServ Policy
- Configure DiffServ Policy Attributes
- Configure DiffServ Policy Settings on an Interface
- View Service Statistics
- 6. Manage Device Security
- Management Security Settings
- Configure RADIUS Settings
- TACACS
- Set Up a Login Authentication List
- Configure Management Access
- Manage Certificates
- Manage Telnet
- Port Authentication Overview
- Traffic Control
- Configure a Private Group
- Private VLAN Overview
- Storm Control Overview
- Control DHCP Snooping Settings
- Configure an IP Source Guard Interface
- Configure Dynamic ARP Inspection
- Access Control List Overview
- Use the ACL Wizard
- Create a MAC ACL
- Configure MAC Rules
- Configure ACL MAC Binding
- View or Delete MAC Bindings
- Configure an IP ACL
- Configure Rules for an IP ACL
- Configure IP Extended Rules
- Configure an IPv6 ACL
- Configure IPv6 Rules
- Configure ACL Interface Bindings
- View or Delete IP ACL Bindings
- View or Delete VLAN ACL Bindings
- 7. Monitoring the System
- 8. Maintenance
- A. Default Settings
- B. Configuration Examples
Manage Device Security
298
M4100 Series Managed Switch
8. In the Denial of Service Min TCP Header Size field, specify the Min TCP Hdr Size allowed.
If DoS TCP fragment is enabled, the switch drops these packets:
• First
TCP fragments with a TCP payload: IP_Payload_Length - IP_Header_Size <
Min_TCP_Header_Size.
• Its range is 0 to 255.
The default value is 20.
9. Use Denial of Service ICMPv4 to enable ICMPv4 DoS prevention.
ICMPv4 DoS prevention causes the switch to drop ICMPv4 packets with a type set to
ECHO_REQ (ping) and a size greater than the configured ICMPv4 Pkt Size.
The factory
default is disabled.
10. Use Denial of Service Max ICMPv4 Packet Size to specify the Max ICMPv4 Pkt Size
allowed.
If ICMPv4 DoS prevention is enabled, the switch drops IPv4 ICMP ping packets with a
size greater than the configured Max ICMPv4 Pkt Size. Its range is 0 to 16376. The
default value is 512.
11. Use Denial of Service ICMPv6 to enable ICMPv6 DoS prevention.
CMPv6 DoS prevention causes the switch to drop ICMPv6 packets with a type set to
ECHO_REQ (ping) and a size greater than the configured ICMPv6 Pkt Size.
The factory
default is disabled.
12. Use Denial of Service Max ICMPv6 Packet Size to specify the Max IPv6 ICMP Pkt Size
allowed.
If ICMPv6 DoS prevention is enabled, the switch drops IPv6 ICMP ping packets with a
size greater than this configured Max ICMPv6 Pkt Size. Its range is 0 to 16376. The
default value is 512.