User's Manual
Table Of Contents
- 8-Port Multi-Gigabit Smart Managed Pro Switch with Two 10G Ports
- Contents
- 1 Get Started
- 2 Configure System Information
- View and Configure the Switch Management Settings
- View or Define System Information and View Software Versions
- View the System CPU Status
- View USB Device Information
- Configure the IPv4 Address for the Network Interface and Management VLAN
- Configure the IPv6 Address for the Network Interface
- View the IPv6 Network Neighbor
- Configure the Time Settings
- Configure DNS Settings
- Configure Green Ethernet Settings
- Use the Device View
- Configure Power over Ethernet
- Configure SNMP
- Configure LLDP
- Configure DHCP Snooping
- Set Up PoE Timer Schedules
- View and Configure the Switch Management Settings
- 3 Configure Switching
- Configure Port Settings and Flow Control
- Configure Link Aggregation Groups
- Configure VLANs
- Configure VLAN Settings
- Configure VLAN Membership
- View VLAN Status
- Configure Port PVID Settings
- Configure MAC-Based VLAN Groups
- Manually Add Members to or Remove Them From a MAC-Based VLAN Group
- Configure Protocol-Based VLAN Groups
- Manually Add Members to or Remove Them From a Protocol-Based VLAN Group
- Configure GARP Switch Settings
- Configure GARP Ports
- Configure a Voice VLAN
- Configure Auto-VoIP
- Configure Spanning Tree Protocol
- Configure Multicast
- View the MFDB Table
- View the MFDB Statistics
- Configure Auto-Video
- IGMP Snooping Overview
- Configure the Global IGMP Snooping Settings
- View the IGMP Snooping Table
- Configure IGMP Snooping for VLANs
- Modify IGMP Snooping Settings for a VLAN
- Disable IGMP Snooping on a VLAN and Remove It From the Table
- IGMP Snooping Querier Overview
- Configure IGMP Snooping Querier
- Configure IGMP Snooping Querier for VLANs
- Display the IGMP Snooping Querier for VLAN Status
- MLD Snooping Overview
- Configure the Global MLD Snooping Settings
- Configure MLD Snooping for a VLAN
- View, Search, and Manage the MAC Address Table
- 4 Configure Routing
- IP Routing Overview
- Configure IP Settings
- Configure VLAN Routing
- Manage IPv4 Routes
- Configure Address Resolution Protocol
- Configure IPv6
- Configure IPv6 Global Settings
- Add a Static IPv6 Route
- Change the Preference for a Static IPv6 Route
- Remove a Static IPv6 Route
- View the IPv6 Route Table
- Configure IPv6 VLAN Interface Settings
- Add an IPv6 Global Address to an IPv6 VLAN
- Change the Settings for an IPv6 Global Address on an IPv6 VLAN
- Remove an IPv6 Global Address From an IPv6 VLAN
- Add an IPv6 Prefix for Advertisement on an IPv6 VLAN
- Change the Settings for an IPv6 Prefix for Advertisement on an IPv6 VLAN
- Remove an IPv6 Prefix From an IPv6 VLAN
- View IPv6 Statistics for an Interface
- View or Clear the IPv6 Neighbor Table
- 5 Configure Quality of Service
- 6 Manage Device Security
- Management Security Settings
- Configure Management Access
- Configure Port Authentication
- Set Up Traffic Control
- Configure Access Control Lists
- Use the ACL Wizard to Create a Simple ACL
- Configure a Basic MAC ACL
- Configure MAC ACL Rules
- Configure MAC Bindings
- View or Delete MAC ACL Bindings in the MAC Binding Table
- Configure an IP ACL
- Configure Rules for a Basic IP ACL
- Configure Rules for an Extended IP ACL
- Configure an IPv6 ACL
- Configure IPv6 Rules
- Configure IP ACL Interface Bindings
- View or Delete IP ACL Bindings in the IP ACL Binding Table
- 7 Monitor the System
- 8 Maintain the Switch and Perform Troubleshooting
- A Configuration Examples
- B Hardware Specifications and Default Settings
Smart Managed Pro Switches MS510TX and MS510TXPP
Configure Routing User Manual180
12. In the Adv NS Interval field, specify the retransmission time of router advertisements that
are sent from the VLAN.
A value of 0 means the interval is not specified for the router.
The range of the neighbor
solicit interval is 1000 to 4294967295. The default is 0.
13. In the Adv Reachable Interval field, specify the router advertisement time.
This is the time allocated to consider the neighbors reachable after
ND confirmation. The
range of reachable time is 0 to 3600000. The default is 0.
14. In the Adv Interval field, specify the maximum time that is allowed between outgoing router
advertisements from the VLAN.
The range of the maximum advertisement interval is 4 to 1800. The default value is 600.
15. From
the Adv Managed Config Flag menu, specify the setting for the router advertisement
managed address configuration flag.
When you select Enable,
end nodes use DHCPv6. When you select Disable, end nodes
autoconfigure addresses. The default value is Disable.
16. From the Adv Other Config Flag menu, select to enable or disable the router
advertisement other stateful configuration flag.
The default value is Disable.
17. From
the Adv Suppress Flag menu, select to enable or disable the router advertisement
suppression on the VLAN.
The default value is Disable.
18. From
the Destination Unreachables menu, select to enable or disable the mode for
sending ICMPv6 destination unreachable messages from the VLAN.
If this mode is disabled, the VLAN does not send ICMPv6 destination unreachable
messages. By default, the IPv6 destination unreachables mode is enabled.
19. Click
the Apply button.
Your settings are saved.
The following table describes the nonconfigurable data that is displayed.
Table 50. IPv6 VLAN Configuration information
Field Description
Operational Mode The operational mode of the VLAN (Enable or Disable).
Link State The state of the link (Link Up or LInk Down).
Add an IPv6 Global Address to an IPv6 VLAN
IPv6 link-local addresses are created automatically when you enable the IPv6 admin mode
on an VLAN interface, and they cannot be removed or edited. However, you can manually
configure IPv6 global addresses on a VLAN.