User's Manual
Table Of Contents
- 8-Port Multi-Gigabit Smart Managed Pro Switch with Two 10G Ports
- Contents
- 1 Get Started
- 2 Configure System Information
- View and Configure the Switch Management Settings
- View or Define System Information and View Software Versions
- View the System CPU Status
- View USB Device Information
- Configure the IPv4 Address for the Network Interface and Management VLAN
- Configure the IPv6 Address for the Network Interface
- View the IPv6 Network Neighbor
- Configure the Time Settings
- Configure DNS Settings
- Configure Green Ethernet Settings
- Use the Device View
- Configure Power over Ethernet
- Configure SNMP
- Configure LLDP
- Configure DHCP Snooping
- Set Up PoE Timer Schedules
- View and Configure the Switch Management Settings
- 3 Configure Switching
- Configure Port Settings and Flow Control
- Configure Link Aggregation Groups
- Configure VLANs
- Configure VLAN Settings
- Configure VLAN Membership
- View VLAN Status
- Configure Port PVID Settings
- Configure MAC-Based VLAN Groups
- Manually Add Members to or Remove Them From a MAC-Based VLAN Group
- Configure Protocol-Based VLAN Groups
- Manually Add Members to or Remove Them From a Protocol-Based VLAN Group
- Configure GARP Switch Settings
- Configure GARP Ports
- Configure a Voice VLAN
- Configure Auto-VoIP
- Configure Spanning Tree Protocol
- Configure Multicast
- View the MFDB Table
- View the MFDB Statistics
- Configure Auto-Video
- IGMP Snooping Overview
- Configure the Global IGMP Snooping Settings
- View the IGMP Snooping Table
- Configure IGMP Snooping for VLANs
- Modify IGMP Snooping Settings for a VLAN
- Disable IGMP Snooping on a VLAN and Remove It From the Table
- IGMP Snooping Querier Overview
- Configure IGMP Snooping Querier
- Configure IGMP Snooping Querier for VLANs
- Display the IGMP Snooping Querier for VLAN Status
- MLD Snooping Overview
- Configure the Global MLD Snooping Settings
- Configure MLD Snooping for a VLAN
- View, Search, and Manage the MAC Address Table
- 4 Configure Routing
- IP Routing Overview
- Configure IP Settings
- Configure VLAN Routing
- Manage IPv4 Routes
- Configure Address Resolution Protocol
- Configure IPv6
- Configure IPv6 Global Settings
- Add a Static IPv6 Route
- Change the Preference for a Static IPv6 Route
- Remove a Static IPv6 Route
- View the IPv6 Route Table
- Configure IPv6 VLAN Interface Settings
- Add an IPv6 Global Address to an IPv6 VLAN
- Change the Settings for an IPv6 Global Address on an IPv6 VLAN
- Remove an IPv6 Global Address From an IPv6 VLAN
- Add an IPv6 Prefix for Advertisement on an IPv6 VLAN
- Change the Settings for an IPv6 Prefix for Advertisement on an IPv6 VLAN
- Remove an IPv6 Prefix From an IPv6 VLAN
- View IPv6 Statistics for an Interface
- View or Clear the IPv6 Neighbor Table
- 5 Configure Quality of Service
- 6 Manage Device Security
- Management Security Settings
- Configure Management Access
- Configure Port Authentication
- Set Up Traffic Control
- Configure Access Control Lists
- Use the ACL Wizard to Create a Simple ACL
- Configure a Basic MAC ACL
- Configure MAC ACL Rules
- Configure MAC Bindings
- View or Delete MAC ACL Bindings in the MAC Binding Table
- Configure an IP ACL
- Configure Rules for a Basic IP ACL
- Configure Rules for an Extended IP ACL
- Configure an IPv6 ACL
- Configure IPv6 Rules
- Configure IP ACL Interface Bindings
- View or Delete IP ACL Bindings in the IP ACL Binding Table
- 7 Monitor the System
- 8 Maintain the Switch and Perform Troubleshooting
- A Configuration Examples
- B Hardware Specifications and Default Settings
Smart Managed Pro Switches MS510TX and MS510TXPP
Configure System Information User Manual50
7. To disable the Energy Detect Admin Mode for port g1, g2, g3, or g4, from the Energy
Detect Admin Mode, select Disable.
The Energy Detect Admin Mode is enabled globally, but you can disable
it for ports g1–g4
only. With this mode enabled, the port transitions to low power mode during a link idle
condition.
The Operational Status field shows whether the energy detect operational
status is active
or inactive.
The Reason field shows the reason for the operational status.
8. T
o disable the Short Reach Admin mode for port g1, g2, g3, or g4, from the Short Reach
Admin mod, select Disable.
The Energy Detect Admin Mode is enabled globally, but you can disable
it for ports g1–g4
only. With this mode enabled, the port transitions to low power mode when the cable
length is too short.
The Operational Status field shows whether the short reach operational
status is active or
inactive.
The Reason field shows the reason for the operational status.
9. Use
the EEE Admin Mode menu to enable or disable this option on the port.
With the EEE mode enabled, the port transitions to low power mode during a link idle
condition.
The default value is Disable.
10. Click the Apply button.
Your settings are saved.
11. T
o refresh the page, click the Refresh button.
12. T
o clear the configuration, resetting all statistics for the selected interface to default values,
click the Clear button.
The following table describes the nonconfigurable fields.
Table 12. Green Ethernet Local Device Information
Field Description
Tw_sys_tx (uSec) The value of Tw_sys that the local system can support.
Tw_sys_tx Echo (uSec) The remote system’s Transmit Tw_sys that was used by the local
system to compute the
Tw_sys that is requested from the remote
system.
Tw_sys_rx (uSec) The value of Tw_sys that the local system requests from the remote
system.
Tw_sys_rx Echo (uSec) The remote system’s Receive Tw_sys that is used by the local system
to compute the
Tw_sys that it can support.










