User manual
Table Of Contents
- Nighthawk X6 AC3200 Tri-Band WiFi Router
- Contents
- 1. Hardware Setup
- 2. Connect to the Network and Access the Router
- 3. Specify Your Internet Settings
- 4. Optimize Performance
- 5. Control Access to the Internet
- 6. Tri-Band WiFi Connections
- 7. Share USB Devices Attached to the Router
- 8. Access USB Devices Through the Internet
- 9. Use the Router as a Media Server
- 10. Share a USB Printer
- 11. Network Settings
- Set Up a Default DMZ Server
- Change the Router’s Device Name
- Change the LAN TCP/IP Settings
- Specify the IP Addresses That the Router Assigns
- Disable the DHCP Server Feature in the Router
- Reserve LAN IP Addresses
- Use the WPS Wizard for WiFi Connections
- Specify Basic WiFi Settings
- Change the WiFi Password or Security Level
- Set Up a Guest Network
- Control the Wireless Radios
- Set Up a Wireless Schedule
- Specify WPS Settings
- 12. Manage Your Network
- 13. Use VPN to Access Your Network
- 14. Specify Internet Port Settings
- 15. Troubleshooting
- Sequence to Restart Your Network
- Check Ethernet Cable Connections
- Wireless Settings
- Network Settings
- Standard LED Behavior When the Router is Powered On
- Power LED Is Off or Blinking
- Power LED Stays Amber
- LEDs Never Turn Off
- Internet or Ethernet Port LEDs Are Off
- WiFi LED Is Off
- Cannot Log In to the Router
- Cannot Access the Internet
- Changes Not Saved
- Wireless Connectivity
- Troubleshoot Your Network Using the Ping Utility
- A. Supplemental Information
Troubleshooting
165
Nighthawk X6 AC3200 Tri-Band WiFi Router
this range, check the connection from the computer to the router, and reboot your
computer.
• If your router’s IP address was changed and you do not know the current IP address,
clear the router’s configuration to factory defaults. This sets the router’s IP address to
192.168.1.1. For more information, see
Factory Settings on page 172.
• Make sure that your browser has Java, JavaScript, or ActiveX enabled. If you are using
Internet Explorer, click the Refresh button to be sure that the Java applet is loaded.
• Try quitting the browser and launching it again.
• Make sure that you are using the correct login information. The user name is admin, and
the default password is password. Make sure that Caps Lock is off when you enter this
information.
• If you are attempting to set up your NETGEAR router as a replacement for an ADSL
gateway in your network, the router cannot perform many gateway services. For
example, the router cannot convert ADSL or cable data into Ethernet networking
information. NETGEAR does not support such a configuration.
Cannot Access the Internet
If you can access your router but not the Internet, check to see if the router can obtain an IP
address from your Internet service provider (ISP). Unless your ISP provides a fixed IP
address, your router requests an IP address from the ISP. You can determine whether the
request was successful using the Router Status screen.
To check the WAN IP address:
1. Launch a web browser from a computer or wireless device that is connected to the
network.
2. Select an external site such as www.netgear.com.
3. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
4. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
5. Click the ADVANCED tab.
The ADVANCED Home screen displays.
6. Check that an IP address is shown for the Internet port. If 0.0.0.0 is shown, your router did
not obtain an IP address from your ISP.
If your router cannot obtain an IP address from the ISP, you might need to force your cable or
DSL modem to recognize your new router by restarting your network. For more information,
see
Sequence to Restart Your Network on page 162.