NETGEAR GS510TP Smart Switch Hardware Installation Guide 350 East Plumeria Drive San Jose, CA 95134 USA October 2011 202-10886-01 1.
NETGEAR GS510TP Smart Switch © 2011 NETGEAR, Inc. All rights reserved No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the written permission of NETGEAR, Inc. Technical Support Thank you for choosing NETGEAR.
Contents About This Manual Conventions, Formats, and Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 How to Print this Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Chapter 1 Introduction Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 PoE Features . . . . . . .
NETGEAR GS510TP Smart Switch Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Additional Troubleshooting Suggestions . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Network Adapter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Switch Integrity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0. About This Manual 0 The NETGEAR® ProSafeTM GS510TP Hardware Installation Guide describes how to install and power on the GS510TP Smart Switch. The information in this manual is intended for readers with intermediate computer and Internet skills. Conventions, Formats, and Scope The conventions, formats, and scope of this manual are described in the following paragraphs: • Typographical Conventions.
NETGEAR GS510TP Smart Switch DANGER: This is a safety warning. Failure to take heed of this notice may result in personal injury or death. • Scope. This manual is written for the GS510TP Smart Switch according to these specifications: Product Version GS510TP Smart Switch Manual Publication Date October 2011 Note: Product updates are available on the NETGEAR, Inc. website at http://kbserver.netgear.com/products/GS510TP.asp.
1. Introduction 1 Congratulations on the purchase of your NETGEAR® ProSafeTM GS510TP Smart Switch. The GS510TP is a supplement to the Gigabit Advanced Smart Switch family. Available as a desktop or rack-mountable.The GS510TP is a PoE-supportable low-port switch with two fiber uplinks included.
NETGEAR GS510TP Smart Switch full-duplex mode. The maximum segment length is 328 feet (100 meters) over Category 5 Unshielded Twisted-Pair (UTP) cable. Features The following list identifies the key features of the GS510TP Smart Switch: • Eight RJ-45 10/100/1000 Mbps autosensing Gigabit Ethernet switching ports. • Two 1000M SFP Gigabit Ethernet switching ports. • Full NETGEAR Smart Switch functionality. • Full compatibility with IEEE standards: • IEEE 802.3 CSMA/CD • IEEE 802.
NETGEAR GS510TP Smart Switch • PoE is enabled by default. Green Features The GS510TP Smart Switch supports the following power-saving features: • The power consumption automatically adjusts based on the RJ-45 cable length. • Each port is configured to power down automatically when the port link is down. Package Contents Figure 1 shows the package contents of the NETGEAR GS510TP Smart Switch. Figure 1.
NETGEAR GS510TP Smart Switch Introduction 10
Physical Description 2. 2 This chapter describes the NETGEAR GS510TP Smart Switch hardware features. Topics include: • GS510TP Front-Panel Configuration • LED Designations • Device Hardware Interfaces GS510TP Front-Panel Configuration The GS510TP has eight 10/100/1000 Mbps autosensing and two 1000 Mbps SFP Gigabit Ethernet switching ports. Each RJ-45 port is capable of sensing the line speed and negotiating the duplex mode with the link partner automatically.
NETGEAR GS510TP Smart Switch • Fan LED • PoE Max LED GS510TP Back-Panel Configuration Figure 3 illustrates the GS510TP back panel. Power Connector Figure 3. GS510TP Back Panel The back panel contains the following: • Internal 150W open frame power supply for the GS510TP.
NETGEAR GS510TP Smart Switch LED Designations Port LEDs Table 1 describes the RJ-45 and SFP port LED designations. There are two LEDs for each RJ-45 port. Each SFP port has its own indication LED. Table 1. Port LEDs LED Designation Speed/Link/Activity SPD/Link/ACT LED: • Off = No link is established on the port. • Solid Green = A valid 1000 Mbps link is established on the port. • Blinking Green = Packets transmission or reception is occurring on the port at 1000 Mbps.
NETGEAR GS510TP Smart Switch System LEDs Table 2 describes the system LED designations. Table 2. System LEDs LED Designation Power/Status LED • Solid Green = Power is supplied to the switch and the switch is operating normally. • Solid Yellow = The switch is booting. • Off = Power is disconnected. PoE MAX LED • Off = There is at least 7W of PoE power available for another device. • Solid Yellow = Less than 7W of PoE power is available.
NETGEAR GS510TP Smart Switch device such as a paper clip into the opening to press the recessed button. The front-panel LEDs should extinguish and light again as the switch performs its Power On Self Test (POST). Factory Defaults Button The Smart Switch has a Factory Defaults button on the front panel so that you can remove the current configuration and return the device to its factory settings.
NETGEAR GS510TP Smart Switch Physical Description 16
3. Applications 3 Your NETGEAR GS510TP Smart Switch is designed to provide flexibility in configuring your network connections. It can be used as a stand-alone device or with 10 Mbps, 100 Mbps, and 1000 Mbps hubs and switches. Desktop Switching The GS510TP Smart Switch can be used as a desktop switch to build a small network that enables users to have 1000 Mbps access to a file server. With full-duplex enabled, the switch port connected to the server or PC can provide 2000 Mbps throughput.
NETGEAR GS510TP Smart Switch Applications 18
4. Installation 4 This chapter describes the installation procedures for your NETGEAR GS510TP Smart Switch.
NETGEAR GS510TP Smart Switch Table 3. Site Requirements (continued) Characteristics Requirements Power source AC power cord (included). Power specifications for the switch are shown in Appendix A. Ensure the AC outlet is not controlled by a wall switch, which can accidentally turn off power to the outlet and the switch. Environmental • Temperature - Install the switch in a dry area, with ambient temperature between 0ºC and 50ºC (32ºC and 122ºF).
NETGEAR GS510TP Smart Switch Step 3: Checking the Installation Before applying power to the switch, perform the following: • Inspect the equipment thoroughly. • Verify that all cables are installed correctly. • Check cable routing to make sure cables are not damaged or creating a safety hazard. • Ensure all equipment is mounted properly and securely. Step 4: Connecting Devices to the Switch The following procedure describes how to connect PCs to the switch’s RJ-45 ports.
NETGEAR GS510TP Smart Switch Note: The PoE port may be considered SELV circuits, if it is not likely to require connection to an Ethernet network with outside plant routing, including campus environment; and the installation instructions clearly state that the ITE is to be connected only to PoEnetworks without routing to the outside plant. Step 5: Applying AC Power Before connecting the power cord, select an AC outlet that is not controlled by a wall switch, which can turn off power to the switch.
NETGEAR GS510TP Smart Switch Note: When the device powers up, there is a default IP address already configured on the device. The default IP address is 192.168.0.239 and subnet mask 255.255.255.0.
NETGEAR GS510TP Smart Switch Installation 24
A. Troubleshooting A This chapter provides information about troubleshooting the NETGEAR Smart Switch. Topics include the following: • Troubleshooting Chart • Additional Troubleshooting Suggestions Troubleshooting Chart The following table lists symptoms, causes, and solutions of possible problems. Table 4. Troubleshooting Chart Symptom Cause Solution Power LED is off. No power is received. Check the power cord connections and the connected device.
NETGEAR GS510TP Smart Switch Table 4. Troubleshooting Chart (continued) Symptom Cause Solution A segment or device is One or more devices are not recognized as part of not properly connected, the network. or cabling does not meet Ethernet guidelines. Verify that the cabling is correct. Ensure all connectors are securely positioned in the required ports. Equipment may have been accidentally disconnected. ACT LED is flashing continuously on all connected ports and the network is disabled.
B. Technical Specifications Network Protocol and Standards Compatibility IEEE 802.3i 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3x flow control IEEE 802.3z 1000BASE-X IEEE 802.3at DTE Power via MDI Management Windows 2000 + XP, Vista; Microsoft Explorer 6.0 or higher IEEE 802.1Q VLAN IEEE 802.3ad Link Aggregation IEEE 802.1D Spanning Tree Protocol IEEE 802.1s Multiple Spanning Trees Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1X Port Security IEEE 802.
NETGEAR GS510TP Smart Switch Protected Port IP and MAC ACL Green feature (Auto power down and Short cable power saving) DoS protection Interface Eight RJ-45 connectors for 10BASE-T, 100BASE-TX, and 1000BASE-T (Auto Uplink™ on all ports) Two SFP slots for SFP modules LEDs Per RJ-45 port: Speed/Link/Activity Per SFP port: SFP indicator Per device: Power Per device: Fan Per device: Max PoE Performance Specifications Forwarding modes: Store-and-forward Bandwidth: 20 Gbps Address database size: 4K media acce
NETGEAR GS510TP Smart Switch Operating humidity: 10% to 90% maximum relative humidity, noncondensing Storage temperature: –20°C to 70°C (–4 to 158°F) Storage humidity: 5% to 95% maximum relative humidity, noncondensing Electromagnetic Emissions FCC Class A CE Class A: Includes EN55022 (CISPR 22), 55024, and 50082-1 VCCI Class A C-Tick KCC CCC Safety UL/cUL CE (includes EN60950-1) CB Technical Specifications 29
NETGEAR GS510TP Smart Switch Technical Specifications 30
Index Numerics G 8-pin 14 Gigabit Ports 7 A H Applying AC Power 22 Auto Uplink 14 Auto-negotiating 8 Autosensing 8, 14 High-speed Servers 7 I IEEE 802.3i 8 IEEE 802.
NETGEAR GS510TP Smart Switch Preparing the Site 19 R Rack-mount Kit 9 Reset Button 11 RJ-45 7 RJ-45 Ports 14 Rubber footpads 9, 20 S Site Requirements 19 Smart Switch Resource CD 9 Straight-through 14 System LEDs 14 T technical support 2 Temperature 20 trademarks 2 Traffic Control 7 Troubleshooting Chart 25 U User Intervention 14 User’s Manual 9 UTP 21 V Ventilation 20 VLAN 7 W Web-based Graphical User Interface 7 32
