User Manual
Table Of Contents
- Contents
- 1. Hardware Overview of the Router
- 2. Connect to the Network and Access the Router
- 3. Specify Your Internet Settings
- Use the Internet Setup Wizard
- Manually set up the Internet connection
- Specify IPv6 Internet connections
- Requirements for entering IPv6 addresses
- Use Auto Config for an IPv6 Internet connection
- Use Auto Detect for an IPv6 Internet connection
- Set up an IPv6 6to4 tunnel Internet connection
- Set Up an IPv6 6rd Tunnel Connection
- Set up an IPv6 pass-through Internet connection
- Set up a fixed IPv6 Internet connection
- Set up an IPv6 DHCP Internet connection
- Set up an IPv6 PPPoE Internet connection
- Manage the MTU size
- 4. Optimize Performance
- 5. Manage the Basic WiFi Network Settings
- 6. Control Access to the Internet
- 7. Share USB Storage Devices Attached to the Router
- USB device requirements
- Connect a USB storage device to the router
- Access a storage device connected to the router
- Map a USB device to a Windows network drive
- Back up Windows-based computers with ReadySHARE Vault
- Back up Mac computers with Time Machine
- Manage Access to a Storage Device
- Enable FTP access within your network
- View network folders on a storage device
- Add a network folder on a USB storage device
- Edit a network folder on a USB storage device
- Safely remove a USB storage device
- 8. Use Dynamic DNS to Access USB Storage Devices Through the Internet
- 9. Use the Router as a Media Server
- 10. Manage the WAN and LAN Network Settings
- Change the WiFi Mbps Settings
- Manage the WAN Security Settings
- Set up a default DMZ server
- Manage IGMP Proxying
- Manage VPN Pass-Through
- Manage NAT Filtering
- Manage the SIP Application-Level Gateway
- Manage the LAN IP Address Settings
- Manage the Router Information Protocol Settings
- Manage the DHCP Server Address Pool
- Manage reserved LAN IP addresses
- Disable the Built-In DHCP Server
- Change the Router’s Device Name
- Set Up and Manage Custom Static Routes
- Set Up a Bridge for a Port Group or VLAN Tag Group
- 11. Manage Your Router
- Update the router firmware
- Change the admin password
- Enable admin password recovery
- Recover the admin password
- Manage the router configuration file
- Disable or Enable LED Blinking or Turn Off LEDs
- Return the router to its factory default settings
- View the Status and Statistics of the Router
- Manage the Activity Log
- View devices currently on the network
- Monitor and Meter Internet Traffic
- Remote access
- 12. Manage the Advanced WiFi Features
- 13. Use VPN to Access Your Network
- 14. Manage Port Forwarding and Port Triggering
- 15. Troubleshooting
- A. Supplemental Information
Quick tips
This section describes tips for troubleshooting some common problems.
Sequence to restart your network
If you must restart your network, follow this sequence:
1.
Turn off and unplug the modem.
2.
Turn off the router.
3. Plug in the modem and turn it on. Wait two minutes.
4. Turn on the router and wait two minutes.
Check the power adapter and Ethernet cable connections
If the router does not start, make sure that the power adapter cable is securely plugged
in.
If the Internet connection or LAN connections do not function, make sure that the
Ethernet cables are securely plugged in. The Internet LED on the router is lit if the
Ethernet cable connecting the router and the modem is plugged in securely and the
modem and router are turned on. If one or more powered-on computers are connected
to the router by an Ethernet cable, the corresponding numbered router LAN port LEDs
light.
Check the WiFi settings
Make sure that the WiFi settings on the WiFi-enabled computer or mobile device and
the router match exactly. The WiFi network name (SSID) and WiFi security settings of
the router and the computer or mobile device must match exactly. WiFi passwords are
case sensitive.
If you set up an access control list, you must add the MAC address of each computer
and mobile device to the router’s access control list.
Check the network settings
If your computer or mobile device cannot connect to the router, make sure that the
network settings of the computer or mobile device are correct. Computers and mobile
devices must use network IP addresses on the same network as the router. By default,
almost all computers and mobile devices are set up to obtain an IP address automatically
using DHCP.
User Manual190Troubleshooting
AC1600 Smart WiFi Router Model R6260