User Manual
Table Of Contents
- Contents
- 1. Hardware Overview of the Router
- 2. Connect to the Network and Access the Router
- 3. Specify Your Internet Settings
- Use the Internet Setup Wizard
- Manually set up the Internet connection
- Specify IPv6 Internet connections
- Requirements for entering IPv6 addresses
- Use Auto Config for an IPv6 Internet connection
- Use Auto Detect for an IPv6 Internet connection
- Set up an IPv6 6to4 tunnel Internet connection
- Set Up an IPv6 6rd Tunnel Connection
- Set up an IPv6 pass-through Internet connection
- Set up a fixed IPv6 Internet connection
- Set up an IPv6 DHCP Internet connection
- Set up an IPv6 PPPoE Internet connection
- Manage the MTU size
- 4. Optimize Performance
- 5. Manage the Basic WiFi Network Settings
- 6. Control Access to the Internet
- 7. Share USB Storage Devices Attached to the Router
- USB device requirements
- Connect a USB storage device to the router
- Access a storage device connected to the router
- Map a USB device to a Windows network drive
- Back up Windows-based computers with ReadySHARE Vault
- Back up Mac computers with Time Machine
- Manage Access to a Storage Device
- Enable FTP access within your network
- View network folders on a storage device
- Add a network folder on a USB storage device
- Edit a network folder on a USB storage device
- Safely remove a USB storage device
- 8. Use Dynamic DNS to Access USB Storage Devices Through the Internet
- 9. Use the Router as a Media Server
- 10. Manage the WAN and LAN Network Settings
- Change the WiFi Mbps Settings
- Manage the WAN Security Settings
- Set up a default DMZ server
- Manage IGMP Proxying
- Manage VPN Pass-Through
- Manage NAT Filtering
- Manage the SIP Application-Level Gateway
- Manage the LAN IP Address Settings
- Manage the Router Information Protocol Settings
- Manage the DHCP Server Address Pool
- Manage reserved LAN IP addresses
- Disable the Built-In DHCP Server
- Change the Router’s Device Name
- Set Up and Manage Custom Static Routes
- Set Up a Bridge for a Port Group or VLAN Tag Group
- 11. Manage Your Router
- Update the router firmware
- Change the admin password
- Enable admin password recovery
- Recover the admin password
- Manage the router configuration file
- Disable or Enable LED Blinking or Turn Off LEDs
- Return the router to its factory default settings
- View the Status and Statistics of the Router
- Manage the Activity Log
- View devices currently on the network
- Monitor and Meter Internet Traffic
- Remote access
- 12. Manage the Advanced WiFi Features
- 13. Use VPN to Access Your Network
- 14. Manage Port Forwarding and Port Triggering
- 15. Troubleshooting
- A. Supplemental Information
(Continued)
DescriptionField
Security Options
If you want to change the WiFi security for an SSID in the 5 GHz band, select one of the following WiFi security
options for that SSID in the guest WiFi network:
•
None. An open WiFi network that does not provide any security. Any WiFi device can join the selected WiFi
network in the 5 GHz band of the guest WiFi network. This is the default setting for the guest WiFi network.
•
WPA2-PSK [AES]. WPA2 provides a secure and fast connection but some older WiFi devices do not detect
WPA2 and support only WPA. Select WPA2-PSK [AES] security to allow 802.11ac and 802.11n devices to
connect to the selected WiFi network in the 5 GHz band of the guest WiFi network at the fastest speed. If
your network includes older devices that do not support WPA2, select WPA-PSK [TKIP] + WPA2-PSK [AES]
security.
To use WPA2 security, in the Passphrase field, enter a phrase of 8 to 63 characters. To join the WiFi network
in the 5 GHz band of the guest WiFi network, a user must enter this passphrase.
•
WPA-PSK [TKIP] + WPA2-PSK [AES]. This type of security enables WiFi devices that support either WPA
or WPA2 to join the selected WiFi network in the 5 GHz band of the guest WiFi network. However, WPA-PSK
[TKIP] is less secure than WPA2-PSK [AES] and limits the speed of WiFi devices to 54 Mbps.
To use WPA + WPA2 security, in the Passphrase field, enter a phrase of 8 to 63 characters. To join the
5 GHz band of the guest WiFi network, a user must enter this passphrase.
The passphrase that provides users access to the selected WiFi network in the 5 GHz
band of the guest WiFi network. The passphrase is also referred to as the password
or key.
Passphrase
6. Click the Apply button.
Your settings are saved.
7. Make sure that you can reconnect over WiFi to the guest network.
If you cannot connect over WiFi, check the following:
•
If your computer or mobile device is already connected to another WiFi network
in your area, disconnect it from that WiFi network and connect it to the WiFi
network that the router provides. Some WiFi devices automatically connect to the
first open network without WiFi security that they discover.
• Does your computer or mobile device display as an attached device? (See View
devices currently on the network on page 147.) If it does, it is connected to the
network.
• Are you using the correct network name (SSID) and password?
User Manual70Manage the Basic WiFi Network
Settings
AC1600 Smart WiFi Router Model R6260