User Manual
Table Of Contents
- Contents
- 1. Hardware Setup
- 2. Connect to Network and Access the Router
- 3. Specify Your Internet Settings
- Use the Internet Setup Wizard
- Manually set up the Internet connection
- Specify IPv6 Internet connections
- Requirements for entering IPv6 addresses
- Use auto config for an IPv6 Internet connection
- Use auto detect for an IPv6 Internet connection
- Set up an IPv6 6to4 tunnel Internet connection
- Set up an IPv6 6rd Internet connection
- Set up an IPv6 pass-through Internet connection
- Set up an IPv6 fixed Internet connection
- Set up an IPv6 DHCP Internet connection
- Set up an IPv6 PPPoE Internet connection
- Change the MTU size
- 4. Optimize Performance
- 5. Control Access to the Internet
- 6. Share USB Storage Devices Attached to the Router
- USB device requirements
- Connect a USB storage device to the router
- Access a storage device connected to the router from a Windows-based computer
- Map a USB device to a Windows network drive
- Access a storage device that is connected to the router from a Mac
- Back up Windows-based computers with ReadySHARE Vault
- Back up Mac computers with Time Machine
- Enable FTP access within your network
- View network folders on a storage device
- Add a network folder on a USB storage device
- Edit a network folder on a USB storage device
- Safely remove a USB storage device
- 7. Use Dynamic DNS to Access USB Storage Devices Through the Internet
- 8. Share a USB Printer
- 9. Manage Network Settings
- View or change the WAN settings
- Set up a default DMZ server
- Change the Router’s Device Name
- Change the LAN TCP/IP settings
- Specify the IP addresses that the router assigns
- Disable the DHCP server feature in the router
- Manage reserved LAN IP addresses
- Use the WPS Wizard for WiFi connections
- Specify Basic WiFi Settings
- Change the WiFi Mode
- Change the WiFi password or the WiFi security
- Enable or disable Smart Connect
- Set up a guest WiFi network
- Control the WiFi radios
- Set up a WiFi schedule
- Specify WPS settings
- Set up the router as a WiFi access point
- Set up the router in bridge mode
- Set up a bridge for a port group or VLAN tag group
- Manage custom static routes
- Enable or disable implicit beamforming
- 10. Manage Your Router
- Update the router firmware
- Change the admin password
- Enable admin password recovery
- Recover the admin password
- View information about the router and the Internet and WiFi settings
- Display the statistics of the Internet port
- Check the Internet connection status
- View and manage logs of router activity
- View devices currently on the network
- Monitor Internet traffic
- Manage the router configuration file
- Remote access
- Remotely access your router using the Nighthawk app
- Disable LED blinking or turn off LEDs
- Set your time zone
- Return the router to its factory default settings
- 11. Use VPN to Access Your Network
- 12. Manage Port Forwarding and Port Triggering
- 13. Troubleshooting
- 14. Supplemental Information
4. Select Wireless.
The Wireless Settings page displays.
5.
In the Wireless Network (2.4 GHz b/g/n) section, select a WiFi mode from the Mode
menu:
•
Up to 54 Mbps. This mode allows 802.11n, 802.11g, and 802.11b devices to
join the network but limits 802.11n devices to functioning at up to 54 Mbps.
•
Up to 217 Mbps. This mode allows for reduced interference with neighboring
WiFi networks. This mode allows 802.11n, 802.11g, and 802.11b devices to join
the network but limits 802.11n devices to functioning at up to 217 Mbps.
•
Up to 450 Mbps. This mode allows 802.11n, 802.11g, and 802.11b devices to
join the network and allows 802.11n devices to function at up to 450 Mbps. This
mode is the default mode.
6. In the Wireless Network (5 GHz a/n/ac) and Wireless Network (5 GHz-2 a/n/ac)
sections, select a WiFi mode from the Mode menus:
•
Up to 289 Mbps. This mode allows 802.11ac, 802.11n, and 802.11a devices to
join the selected WiFi network in the 5 GHz band of the network but limits
802.11ac and 802.11n devices to functioning at up to 289 Mbps.
•
Up to 600 Mbps. This mode allows for reduced interference with neighboring
WiFi networks. This mode allows 802.11ac, 802.11n, and 802.11a devices to join
the selected WiFi network in the 5 GHz band of the network but limits 802.11ac
devices to functioning at up to 600 Mbps.
•
Up to 1300 Mbps. This mode allows 802.11ac, 802.11n, and 802.11a devices
to join the selected WiFi network in the 5 GHz band of the network and allows
802.11ac devices to function at up to 1300 Mbps.
Note: If you enabled Smart Connect, both 5 GHz WiFi bands must use the same
WiFi settings. If you want to use different settings for each 5 GHz WiFi band, you
must first disable Smart Connect.
7. Click the Apply button.
Your settings are saved.
User Manual98Manage Network Settings
Nighthawk X6 AC3000 Tri-Band WiFi Router