NETGEAR Wireless-N Access Point WN802T v2 Reference Manual (802.11bgn) NETGEAR, Inc.
© 2008 by NETGEAR, Inc. All rights reserved.. Technical Support Please refer to the support information card that shipped with your product. By registering your product at http://www.netgear.com/register, we can provide you with faster expert technical support and timely notices of product and software upgrades. NETGEAR, INC. Support Information Phone: 1-888-NETGEAR, for US & Canada only. For other countries, see your Support information card. E-mail: support@netgear.
Regulatory Compliance Information This section includes user requirements for operating this product in accordance with National laws for usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable National regulatory authority. NOTE: This product's firmware limits operation to only the channels allowed in a particular Region or Country.
Lietuvių [Lithuanian] Šiuo NETGEAR Inc. deklaruoja, kad šis Radiolan atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands [Dutch] Hierbij verklaart NETGEAR Inc. dat het toestel Radiolan in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese] Hawnhekk, NETGEAR Inc., jiddikjara li dan Radiolan jikkonforma mal-htigijiet essenzjali u ma provvedimenti ohrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
FCC Declaration Of Conformity We NETGEAR, Inc., 4500 Great America Parkway, Santa Clara, CA 95054, declare under our sole responsibility that the model WN802T v2 NETGEAR Wireless-N Access Point WN802T v2 complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation.
Product and Publication Details Model Number: WN802T v2 Publication Date: September 2008 Product Family: Wireless Access Point Product Name: NETGEAR Wireless-N Access Point WN802T v2 Home or Business Product: Business Language: English Publication Part Number: 202-10415-01 Publication Version Number: 1.0 vi v1.
Contents About This Manual Conventions, Formats and Scope ...................................................................................xiii How to Use This Manual .................................................................................................xiv How to Print this Manual ..................................................................................................xiv Revision History .................................................................................................
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Chapter 3 Wireless Security Settings Wireless Security Options ..............................................................................................3-1 SSID and WEP/WPA Settings Setup Form ....................................................................3-5 RADIUS Server Settings ................................................................................................3-6 Configuring Wireless Security ..............................
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual The Ethernet light is not lit. .......................................................................................6-2 The WLAN light is not lit. .........................................................................................6-2 I cannot configure the access point from a browser. ...............................................6-3 I cannot access the Internet or the LAN with a wireless capable computer. ...........
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual xii Contents v1.
About This Manual The NETGEAR® Wireless-N Access Point WN802T v2 Reference Manual describes how to install, configure, and troubleshoot the NETGEAR Wireless-N Access Point WN802T v2. The information in this manual is intended for readers with intermediate computer and Internet skills. Conventions, Formats and Scope The conventions, formats, and scope of this manual are described in the following paragraphs: • • Typographical Conventions.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Danger: This is a safety warning. Failure to take heed of this notice may result in personal injury or death. • Scope.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual • Printing a Page in the HTML View. Each page in the HTML version of the manual is dedicated to a major topic. Use the Print button on the browser toolbar to print the page contents. • Printing a Chapter. Use the PDF of This Chapter link at the top left of any page. – Click the PDF of This Chapter link at the top right of any page in the chapter you want to print. The PDF version of the chapter you were viewing opens in a browser window.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual xvi About This Manual v1.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Chapter 1 Introduction This chapter describes some of the key features of the NETGEAR Wireless-N Access Point WN802T v2. It also includes the minimum prerequisites for installation (“System Requirements” on page 1-3.), package contents (“What is in the Box” on page 1-3), and a description of the front and back panels of the WN802T v2 (“Front Panel of the NETGEAR Wireless-N Access Point” on page 1-3).
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual • Multi-In, Multi-Out (MIMO) technology. Provides improved communication performance without additional bandwidth or transmit power. . • Standards Compliance. Complies with Draft 2.0 802.11n for wireless LANs, and is backward compatible with 802.11bg. • Full WPA and WPA2 support. WPA and WPA2 personal and enterprise-class strong security with dynamic encryption key generation. TKIP and AES encryption are supported.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual System Requirements Before installing the WN802T v2, make sure your system meets the following requirements: • • • • • • A 10/100/1000 Mbps Local Area Network device such as a hub, switch or, router. The Category 5 UTP straight through Ethernet cable with RJ-45 connector included in the package, or one like it. A 100-240 V, 50-60 Hz AC Switching Power Supply. A Web browser for configuration such as Microsoft Internet Explorer 6.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual P Power LAN WLAN Figure 1-1 Front panel status LEDs You can use the status lights on the front of the wireless access point to verify various conditions described in the following table: Table 1-1. Port and system LEDs Feature Detailed Description LAN Port LED Link/Act Green – Giga Ethernet link is properly made Amber – Fast Ethernet link is properly made Sparkle – Active Off – No Link is detected WLAN LED Wireless Link/Act Green– A 802.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Back Panel of the NETGEAR Wireless-N Access Point The back of the WN802T v2 contains the following listed items, viewed from top to bottom: Reset button Ethernet port Power outlet Figure 1-2 Back panel of the WN80Tv2 1. The Reset button, which is used to reset the WN802T v2 or restore the factory default settings. See Appendix A, “Default Settings and Technical Specifications” for more information on restoring the factory default settings. 2.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Figure 1-3 Label on back panel 1-6 Introduction v1.
Chapter 2 Installation and Configuration This chapter describes how to set up your NETGEAR Wireless-N Access Point WN802T v2 for wireless connectivity to your LAN. This basic configuration will enable computers with 802.11bgn or 802.11bg wireless adapters to connect to the Internet, or access printers and files on your LAN. Note: Indoors, computers can connect over 802.11bgn or 802.11bg wireless networks at ranges of several hundred feet or more.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Note: Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the WN802T v2. For complete performance specifications, see Appendix A, “Default Settings and Technical Specifications”. For best results, place your wireless access point: • Near the center of the area in which your PCs will operate.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 3. Connect an Ethernet cable from the WN802T v2 to the computer. 4. Connect the power adapter to the WN802T v2 and verify the following: • The PWR power light goes on. • The Ethernet port of the wireless access point is lit when connected to a powered on computer. • The WLAN LED should be blinking.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual • Click Logout to exit the WN802T v2. (You will automatically be logged out of the wireless access point after 5 minutes of no activity.) To set the Access Point Name and Country/Region: 1. On logging in, the General settings screen under Configuration > System > Basic displays.. Figure 2-2 Access Point name and Country/Region 2. Enter the Access Point Name of the WN802T v2. The access point name is printed on the back label of the WN802T v2.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual To select the local time zone: 1. Select Configuration > System > Basic > Time. The Time Settings screen displays. Figure 2-3 Local time zone settings 2. Configure the following information: – Time Zone. From the pull-down menu, select the local time zone for your wireless access point from a list of all available time zones. The default is Pacific Time (US-Canada). – Daylight Saving. This option is always disabled.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 3. .Click Apply to save your settings. To configure the Basic LAN settings: 1. Select IP under Configuration on the main menu. The IP Settings screen displays (see Figure 2-4).The default settings should be suitable for most users and environments. Figure 2-4 Basic IP settings 2. Enter the IP Settings fields of the WN802T v2. – DHCP Client. By default, the Dynamic Host Configuration Protocol (DHCP) client is disabled.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual – Primary DNS Server. The WN802T v2 uses this IP address as the primary Domain Name server used by stations on your LAN. – Secondary DNS Servers. The WN802T v2 uses this IP address as the secondary Domain Name Server used by stations on your LAN. 3. Click Apply to save your Basic IP settings. Note: If you change the default subnet of the LAN IP address, you will be disconnected from the NETGEAR Wireless-N Access Point user interface.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 2. Configure the Wireless LAN settings based on the following field descriptions: • Wireless Mode. Select the desired wireless operating mode by clicking inside the appropriate radio button: – 11b – 802.11b wireless stations can be used (802.11g and 802.11ng wireless stations can still be used if they can operate in 802.11b mode.). – 11bg – both 802.11b and 802.11bg wireless stations can be used (802.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual • – If using multiple access points, it is better if adjacent access points use different channels to reduce interference. NETGEAR recommends a channel spacing of 5 channels (for example, channels 1, 6, and 11). between adjacent access points. – Wireless stations normally scan all channels, looking for an access point. If more than one access point can be used, the one with the strongest signal is used.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Configuring QoS Settings WMM Support. Wi-Fi Multimedia (WMM) is a Quality of Service (QoS) feature and part of the 802.11e standard. It provides for prioritization of wireless data packets from different applications based on four access categories: voice, video, best effort, and background. Time-dependent information, such as video or audio, has a higher priority than normal traffic.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Configuring WMM Power Save WMM power save is a set of features in 802.11e that help to conserve power for battery-operated devices in a wireless LAN. To configure WMM Power Save settings: 1. Under the Configuration tab on the main menu, select Wireless, then select QoS Settings under Basic from the side menu. The QoS settings screen displays (see Figure 2-6). 2. WMM Power Save is enabled by default. Check the Disable checkbox to disable it. 3.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Deploying the NETGEAR Wireless-N Access Point Now that you have completed the setup steps, you can deploy the WN802T v2 in your network. If needed, you can now reconfigure the computer you used in step 1 in “Configuring the NETGEAR Wireless-N Access Point” on page 2-2 back to its original TCP/IP settings. To deploy the NETGEAR Wireless-N Access Point: 1. Disconnect the WN802T v2 and position it where it will be deployed.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Logging in to the NETGEAR Wireless-N Access Point The WN802T v2 is set, by default, with the IP address of 192.168.0.233 with DHCP disabled. Note: If logging in using the default IP address, the computer you are using to connect to the WN802T v2 should be configured with an IP address that starts with 192.168.0.x and a subnet mask of 255.255.255.0.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 2. Connect to the WN802T v2 by entering the default address of http://192.168.0.233 into your browser. http://192.168.0.233 http://192.168.0.233 Figure 2-8 Default IP address of the WN802T v2 3. The login screen displays (see Figure 2-1). Enter admin for the user name and password for the password, both in lower case letters. 4. Click Login.
Chapter 3 Wireless Security Settings Your wireless data transmissions can be received well beyond your walls by anyone with a compatible adapter. For this reason, use the security features of your wireless equipment. The NETGEAR Wireless-N Access Point provides highly effective security features which are covered in detail in this chapter. Deploy the security features appropriate to your needs.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual • Use WPA or WPA-PSK. Wi-Fi Protected Access (WPA) data encryption provides data security. The very strong authentication along with dynamic per frame rekeying of WPA make it virtually impossible to compromise. Because this is a new standard, wireless device driver and software availability may be limited. Figure 3-1 Basic security settings Security options are available under Configuration > Security > Security Settings (see Figure 3-1).
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual – Network Authentication. The WN802T v2 Access Point is set by default as an open system (no authentication) with no data encryption. When setting up Network Authentication, bear in mind the following: – If you are using Access Point mode, then all options are available. In other modes such as Repeater or Bridge, some options may be unavailable. – Not all wireless adapters support WPA or WPA2.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual – Data Encryption. The available options depend on the Network Authentication setting selected (see Table 3-1); otherwise, the default is None. The data encryption settings are explained in the following table: Table 3-2. Data Encryption Settings Data Encryption Type Description None No encryption is used. 64 bits WEP Standard WEP encryption, using 40/64 bit encryption. 128 bits WEP Standard WEP encryption, using 104/128 bit encryption.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual – Wireless Client Security Separation. If enabled, the associated wireless clients will not be able to communicate with each other (this feature is intended for hotspots and other public access situations). The default is No. Note: If you are using a RADIUS server, configure the RADIUS settings first, as described in the “Configuring WPA with RADIUS” on page 3-8. SSID and WEP/WPA Settings Setup Form 802.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Record the WPA-PSK/WPA2-PSK key ___________________________________ • WPA RADIUS Settings.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 2. From the Data Encryption drop-down menu, select encryption strength (64-bit, 128-bit, or 152-bit). For Open System, the default is None. If encryption is selected, fields for the passphrase and four keys display on the same screen (see Figure 3-2). Figure 3-2 WEP - Data encryption keys 3. You manually or automatically program the four data encryption keys. These values must be identical on all PCs and wireless access points in your network.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Note: If you use a wireless computer to configure WEP settings, you will be disconnected when you click Apply. Reconfigure your wireless adapter to match the new settings or access the wireless access point from a wired computer to make any further changes. Configuring WPA with RADIUS Not all wireless adapters support WPA. Furthermore, client software is required on the client.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 4. Under the Configuration tab, select Security from the main menu, and then select Security Settings from the side menu. Figure 3-3 WPA with RADIUS security settings 5. Select WPA with RADIUS from the Network Authentication drop-down menu. Data encryption will be set to TKIP by default (see Figure 3-3). 6. Wireless Client Security Separation is disabled by default.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Configuring WPA2 with RADIUS Not all wireless adapters support WPA2. Furthermore, client software is required on the client. Make sure your client card supports WPA2. Consult the product document for your wireless adapter and WPA2 client software for instructions on configuring WPA2 settings. Figure 3-4 WPA2 with RADIUS security settings To configure WPA2 with RADIUS: 1.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Configuring WPA and WPA2 with RADIUS Not all wireless adapters support WPA and WPA2. Client software is required on the client: • Vista, Windows XP and Windows2000 with Service Pack 3 or later, do include the client software that supports WPA/WPA2. The wireless adapter hardware and driver must also support WPA/WPA2. • Service Pack 3 does not include the client soft ware that supports WPA2. Make sure your client card supports WPA2.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 4. Under the Configuration tab, select Security from the main menu, and then select Security Settings from the side menu. From the Network Authentication drop-down menu, select WPA & WPA2 with RADIUS from the list. By default, Data Encryption will be set to TKIP+AES. 5. Wireless Client Security Separation is disabled by default. If enabled, associated wireless clients will not be able to communicate with each other.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual To configure WPA-PSK: 1. From the Configuration menu select Security and from the side menu select Security Settings. 2. From the Network Authentication drop-down menu, select WPA-PSK. By default, Data Encryption will be set to TKIP+AES (see Figure 3-6). 3. Enter the preshared key passphrase (Network Key). 4. Wireless Client Security Separation is disabled by default.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 2. From the Network Authentication drop-down menu, select WPA2-PSK from the list. By default, Data Encryption will be set to TKIP+AES. (see Figure 3-7) 3. Enter the preshared key passphrase (Network Key). 4. Wireless Client Security Separation is disabled by default. If enabled, associated wireless clients will not be able to communicate with each other. (This feature is intended for hotspots and other public access situations). 5.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual To configure WPA-PSK and WPA2-PSK: 1. From the Configuration menu select Security and from the side menu select Security Settings. 2. From the Network Authentication drop-down menu, select WPA-PSK & WPA2-PSK. By default, Data Encryption will be set to TKIP+AES (see Figure 3-8). 3. Enter the WPA Passphrase (Network Key). 4. Wireless Client Security Separation is disabled by default.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Figure 3-9 Access control list 3. Check the Turn Access Control On checkbox to enable the access control feature. 4. Select the desired access control database from the Select Access Control Database dropdown menu.The options are: • Local MAC Address Database – The access point will use the local MAC address table for access control. This is the default.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 9. Click Add to add the wireless device to the Trusted Wireless Stations list. Repeat these steps for each additional device you want to add to the list. 10. Click Apply to save your wireless access control list settings. Now, only devices on this list will be allowed to wirelessly connect to the WN802T v2. Wireless Security Settings 3-17 v1.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 3-18 Wireless Security Settings v1.
Chapter 4 Management This chapter describes how to use the management and information features as well as the advanced wireless settings features of your NETGEAR Wireless-N Access Point WN802T v2. The management and information features can be found under the Maintenance tab on the main menu. Changing the Administrator Password Note: Before changing the WN802T v2 password, use the backup utility to save your configuration settings.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual . Figure 4-1 Change password 2. Enter the current password, in the Current Password field. 3. Enter the new password, twice, in the New Password and Repeat New Password fields. 4. Click Apply to save your changes. Note: Be sure to write down the new password and store it in a safe place. To restore the default password: 1. Select the Restore Default Password radio button (see Figure 4-1). 2. Click Apply. The default password is restored.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Upgrading the Wireless Access Point Firmware The software of the NETGEAR Wireless-N Access Point is stored in FLASH memory, and can be upgraded as new software is released by NETGEAR. Firmware upgrade files can be downloaded manually from the NETGEAR Web site. The upgrade file can then be sent using your browser as shown in the following steps.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 6. The WN802T v2 will check if the file is valid and load it in to the firmware. Once the file has been loaded the AP reboots. Warning: When uploading firmware to the WN802T v2, it is important not to interrupt the Web browser by closing the window, clicking a link, or loading a new page. If the browser is interrupted, the upload may fail, corrupt the software, and render the WN802T v2 inoperable.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual The current settings are saved to a file under the default name Config. To restore settings from a backup file: 1. In Step 1 of the previous section, click Restore Settings on the side menu.. Figure 4-4 Restore saved configuration settings 2. Click Browse at the Restore Saved Settings from a File box. Locate and select the previously saved backup file (by default, Config). 3. Click Apply.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual To reboot the wireless access point from the user interface: 1. From the main menu of the browser interface, select Maintenance > Reset and then Reboot AP on the side menu. The Reboot AP screen displays as follows:. Figure 4-5 Reboot the AP 2. Select the Yes radio button next to the Reboot option, and then click Apply.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual The factory settings are restored and the access point reboots. This takes about a minute. A list of the factory default settings can be found in the appendix in.Table A-1. Warning: Do not try to go online, turn off the Access Point, shut down the computer or do anything else to the Access Point until it finishes restarting. When the PWR light turns green, wait a few more seconds before doing anything with the Access Point.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual • If the wireless access point is rebooted, the table data is lost until the wireless access point rediscovers the devices. Note: A wireless network can include multiple wireless access points, all using the same network name (SSID). This extends the reach of the wireless network and lets users roam from one access point to another which provides seamless network connectivity.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Table 4-1. System Information fields (continued) Field Description Current IP Settings IP Address The IP address of the wireless access point. Subnet Mask The subnet mask for the wireless access point. Default Gateway The default gateway for the wireless access point communication. DHCP Client Enabled indicates that the current IP address was obtained from a DHCP server on your network. Disabled indicated a static IP configuration.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual To display statistics for the wireless access point: 1. Select Statistics under the Monitoring tab on the main menu. The Statistics screen displays. • The Wired Ethernet section of the table displays traffic statistics for the wired ethernet interface. • The Wireless 11ng section displays traffic statistics for the wireless interface. Figure 4-8 Network traffic statistics 2. Click Refresh to update the current statistics.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Table 4-2. Statistics Fields (continued) Field Description Broadcast Packets The number of broadcast packets sent and received since the WN802T v2 was restarted. Multicast Packets The number of multicast packets sent and received since the WN802T v2 was restarted. Total Packets The total number of wireless packets sent and received since the WN802T v2 was restarted.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual The default value is 100 ms. • Aggregation Length. The default value is 65535 bytes. • AMPDU (Aggregated-MAC Packet Data Unit). This is a feature in IEEE 802.11e and 802.11n Wireless LAN Standard, which allows to build a group of frames before they are transmitted. The default is Enabled • RIFS (Reduced Inter-Frame Spacing) transmission. The default is Disabled. • DTIM Interval.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 2. Make the required changes or selections to the Wireless LAN Parameters section, based on the field descriptions outlined earlier. 3. Click Apply for your changes to take effect. Configuring the RADIUS Server Settings RADIUS (Remote Authentication Dial In User Service) is a protocol for managing Authentication, Authorization and Accounting (AAA) of multiple users in a network.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual • • Authentication Server. This configuration is required for authentication using a RADIUS Server.The IP Address, Port Number, and Shared Secret are required for communication with the Primary RADIUS Server. You can also configure a Secondary RADIUS Server to use, if the Primary RADIUS Server fails. – IP Address. The IP address of the RADIUS Server. – Port Number. The port number of the RADIUS Server. The default is 1812. – Shared Secret.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual RADIUS Server Settings Fields Table 4-3. RADIUS server settings fields Field Description Primary and Secondary Authentication Servers The Authentication RADIUS server provides authentication and access control. The primary server is mandatory. A secondary server, which will be used if the primary server fails, is optional. IP Address The IP address of the authentication server. If no server is present leave blank.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 4-16 Management v1.
Chapter 5 Advanced Wireless Bridging This chapter describes how to configure the advanced features of your WN802T v2 to one of six access point bridge mode profiles, or in Wireless Bridge and Repeater Mode.These features can be found under the Wireless Bridge option on the Configuration menu. Note: Only one of a number of WN802T v2 APs in point-to-point bridge mode connected to one another can have six profiles. The NETGEAR Wireless-N Access Point WN802T v2 lets you build large wireless networks.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual To configure wireless Point to Multi-point Bridging: 1. Open a web browser and log in to the WN802T v2 using the addressing scheme you have set up. . Figure 5-1 Enable wireless bridging and repeating 2. Under the Configuration tab on the main menu, click Wireless Bridge. The Bridging and Repeating screen displays showing the default settings for the wireless access point (Figure 51). 3.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 7. Enter the MAC (physical) address of the other bridge mode wireless access point in the Remote MAC Address field. Figure 5-2 Edit security profile 8. Under Authentication Settings, select one of the network authentication types from the Network Authentication drop-down menu (one of the supported types—WEP, WPA-PSK, or WPA2-PSK should be used to protect the communication). 9. Select encryption strength from the Data Encryption options available.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual The following figure illustrates a multi-point bridge setup over three LAN segments. AP2 AP3 Point-to-Point Bridge Mode Wireless PC Card in a Notebook Computer Point-to-Point Bridge Mode AP1 Router 192.168.0.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual • That all wireless access points are using the same SSID, Channel, WEP authentication mode, if any, and encryption (WPA is not available in bridge mode). • That each Point-to-Point AP has the Multi-Point AP MAC address in its Remote AP MAC address table. • That the Multi Point-to-Point AP has the MAC addresses of each Point-to-Point AP.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual To configure the WN802T v2 in wireless repeater mode: 1. Open a web browser and log in to the WN802T v2 using the addressing scheme you have set up. Figure 5-4 Repeater without wireless association 2. Under the Configuration tab on the main menu, click Wireless Bridge. The Bridging and Repeating screen displays showing the default settings for the wireless access point (see Figure 5-4). 3.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 10. From the Data Encryption drop-down menu select encryption strength. 11. Click Apply to save your settings. 12. You are taken back to the Wireless Bridge Settings screen (Figure 5-4) with the new profile information. Enable the profile now if you wish to. 13. Click Apply to save your changes. To configure a LAN segment utilizing the WN802T v2 in Repeater Mode: 1. Configure the Operating Mode of the NETGEAR Wireless-N Access Points.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 5-8 Advanced Wireless Bridging v1.
Chapter 6 Troubleshooting and Help This chapter provides information for troubleshooting issues with your NETGEAR Wireless-N Access Point WN802T v2 and how to avail the help features and options provided. Offline help Offline Help is available for each page by clicking the small “?” symbol at the top right corner of the current screen information. For example, by clicking the help symbol on the Wireless Bridge Settings screen the following help page displays: 6-1 v1.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Troubleshooting Following are some simple problems that could occur and their possible causes. Along with each problem description, instructions are provided to assist you in diagnosing and solving the problem. No lights are lit on the access point. The access point has no power. • Make sure the power cord is connected to the access point and plugged in to a working power outlet or power strip.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual • Contact NETGEAR if the WLAN light remains off. Figure 6-1 Turn Radio On button must be selected I cannot configure the access point from a browser. Check these items: • The WN802T v2 is properly installed, LAN connections are OK, and it is powered on. Check that the LAN port LED is blinking green to verify that the Ethernet connection is OK.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual I cannot access the Internet or the LAN with a wireless capable computer. There is a configuration problem. Check these items: • You may not have restarted the computer with the wireless adapter to have TCP/IP changes take effect. Restart the computer. • The computer with the wireless adapter may not have the correct TCP/IP settings to communicate with the network. Restart the computer and check that TCP/IP is set up properly for that network.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual • Reboot: When pressed and released quickly, the WN802T v2 will reboot (restart). • Reset to Factory Defaults: This button can also be used to clear ALL data and restore ALL settings to the factory default values. These settings are shown in Appendix A, “Default Settings and Technical Specifications”. To clear all data and restore the factory default values: 1. Power off the WN802T v2 and power it back on. 2.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual 6-6 Troubleshooting and Help v1.
Appendix A Default Settings and Technical Specifications This appendix provides the factory default settings and technical specifications for the NETGEAR Wireless-N Access Point WN802T v2. Factory Default Settings You can use the Reset button located on the front of your device to reset all settings to their factory defaults. This is called a hard reset. • To perform a hard reset, push and hold the Reset button for approximately 5 seconds (until the Power LED changes from blinking green to solid amber).
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Table A-1.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Table A-2. WN802T v2 Technical Specifications (continued) Parameter NETGEAR Wireless-N Access Point WN802T v2 802.11bg Data Rates 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 & 54 Mbps (Auto-rate capable) 802.11b/bg/ngb Operating Frequencies 2.412 ~ 2.462 GHz (US) 2.457 ~ 2.462 GHz (Spain) 2.412 ~ 2.484 GHz (Japan) 2.457 ~ 2.472 GHz (France) 2.412 ~ 2.472 GHz (Europe ETSI) 802.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual A-4 Default Settings and Technical Specifications v1.
Appendix B Related Documents This appendix provides links to reference documents you can use to gain a more complete understanding of the technologies used in your NETGEAR product. Document Link Internet Networking and TCP/IP Addressing http://documentation.netgear.com/reference/enu/tcpip/index.htm Wireless Communications http://documentation.netgear.com/reference/enu/wireless/index.htm Preparing a Computer for Network Access http://documentation.netgear.com/reference/enu/wsdhcp/index.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual B-2 Related Documents v1.
Index Numerics 20 MHz legacy mode static 2-9 20/40 MHz compatibility mode, dynamic 2-9 40 MHz high-throughput, static 2-9 802.11 IEEE standard 3-7 802.11b mode legacy 2-8 set 2-8 settings 2-7 standard access point 5-1 802.11b/bg/ng compatibility, wireless adapter 2-2 mode current settings 4-9 encryption strength A-3 operating frequencies A-3 setup form, for 3-5 network, range 2-1 system requirements 1-3 wireless adapter, compatibility 2-1 WN802Tv2 modes A-2 802.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual unauthorized 2-1 access control available wireless stations 3-16 enable 3-16 MAC address database, local 3-16 MAC address database, remote 3-16 MAC address filtering 1-2 trusted wireless stations 3-16 access control list 3-15 access point ethernet, connection to 2-2 placement 2-12 access point mode system information 4-9 access point name 4-8 default 2-4 accounting server.
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual wireless, test 2-12 AES, WPA2 with RADIUS 3-3, 3-10 AES, WPA2-PSK 3-14 AES/TKIP+AES 3-3 default A-2 key generation, dynamic 1-2 none 3-3 number of digits 3-7 open system 3-3 point to multi-point bridging 5-3, 5-5 shared key, WEP 3-3 strengths, available A-1 strengths/types A-3 TKIP+AES 3-3, 3-12, 3-15 TKIP+AES,WPA-PSK+WPA2-PSK 3-15 TKIP, WPA with RADIUS 3-9 TKIP, WPA-PSK 3-13 TKIP/TKIP+AES 3-3 type, supported 1-2 WEP 3-1 WEP, configure 3-6 wireless
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual L front panel 1-2 LAN setting 2-3 G latency 2-1 guard interval 2-9 LED status 1-5 H legacy mode channel width, static 2-9 Help offline 6-1 online 6-5 line of sight 2-12 location access point 2-1 placement 2-12 high-throughput mode static 2-9 hotspot wireless client security separation 3-5 to 3-15 log in 2-13 I M interference electromagnetic 1-1 guard interval 2-9 sources 2-2 what to do if 2-8 MAC address filtering 3-1 location 3-17
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual see also passphrase 3-14 WPA2-PSK 3-14 WPA-PSK/WPA2/PSK 3-15 power consumption 2-1 power save 2-11 network key/passphrase 3-4 power supply 1-3 outlet 1-6 NTP client enable 2-5 preamble type 4-12 NTP Server custom 2-5 prioritize traffic 1-2 NTP server hostname/IP address 2-5 O open authentication 3-1 preshared key passphrase 3-4, 3-13 Q QoS 2-10 see Quality of Service open system 3-3, 3-5, 3-6, 3-7 QoS settings configure 2-10 output pow
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual factory default settings 4-6 saved settings 4-5 standards wireless 1-2 RIFS 4-12 RTS packet CSMA/CA 4-11 statistics fields description, network traffic 4-10 network traffic 4-10 RTS threshold 4-11 default value 4-11 subnet mask default 2-2, 2-6 Support 1-iii system information access point mode 4-9 access point name 4-8 channel/frequency 4-9 country/region 4-8 DHCP client, status 4-9 fields, description of 4-8 firmware version 4-8 IP address 4-
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual U upgrade firmware 4-3 user name default 2-3, 2-11, 2-14 users maximum 1-1 W warranty 1-3 WEP 3-1 configure 3-6 wireless connection, lose 3-15 connectivity, test 2-11, 2-12 wireless access by MAC address restricting 3-15 wireless bridge different configurations 5-1 multi-point 5-1 multi-point, configure 5-1 repeater without client association 5-1 security profile 5-1 standard access point mode 5-1 wireless bridging enable 5-2 wireless client roami
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual WPA2-PSK 3-3 configure 3-13 WPA-PSK 3-3 configure 3-12 restrictions 3-12 WPA-PSK/WPA2-PSK 3-3 configure 3-14 Index-8 v1.
