Owner's Manual
Table Of Contents
- User Manual
- Contents
- 1. Hardware Setup
- 2. Connect to the network and access the router
- 3. Specify Your Internet Settings
- Use the Internet Setup Wizard
- Manually set up the Internet connection
- Specify IPv6 Internet connections
- Requirements for entering IPv6 addresses
- Use auto detect for an IPv6 Internet connection
- Set up an IPv6 6to4 tunnel Internet connection
- Set up an IPv6 pass-through Internet connection
- Set up an IPv6 fixed Internet connection
- Set up an IPv6 DHCP Internet connection
- Set up an IPv6 PPPoE Internet connection
- Use auto config for an IPv6 Internet connection
- Set up an IPv6 6rd Internet connection
- Manage the MTU size
- 4. Control Access to the Internet
- 5. Manage Network Settings
- View or change the WAN settings
- Set up a default DMZ server
- Change the Router’s Device Name
- Change the LAN TCP/IP settings
- Specify the IP addresses that the router assigns
- Disable the DHCP server feature in the router
- Manage reserved LAN IP addresses
- Use the WPS Wizard for WiFi connections
- Specify basic WiFi settings
- Change the WiFi mode
- Change the WiFi password or the WiFi security
- Set up a guest WiFi network
- Enable or disable the WiFi radios
- Set up a WiFi schedule
- Specify WPS settings
- Set up the router as a WiFi access point
- Set up a bridge for a port group or VLAN tag group
- Manage custom static routes
- Enable or disable implicit beamforming
- Enable or disable MU-MIMO
- Enable or disable AX WiFi
- Enable bridge mode
- 6. Optimize Performance
- 7. Manage Your Router
- Update the router firmware
- Change the admin password
- Enable admin password recovery
- Recover the admin password
- View information about the router and the Internet and WiFi settings
- Display the statistics of the Internet port
- Check the Internet connection status
- View and manage logs of router activity
- View devices currently on the network
- Monitor Internet traffic
- Manage the router configuration file
- Connect to your router with Anywhere Access
- Turn off the router LEDs
- Set your time zone
- Specify ReadyDLNA media server settings
- Return the router to its factory default settings
- 8. Share USB Storage Devices Attached to the Router
- USB device requirements
- Connect a USB storage device to the router
- Access a storage device connected to the router from a Windows-based computer
- Map a USB device to a Windows network drive
- Access a storage device that is connected to the router from a Mac
- Enable FTP access within your network
- View network folders on a storage device
- Add a network folder on a USB storage device
- Edit a network folder on a USB storage device
- Safely remove a USB storage device
- 9. Use Dynamic DNS to Access USB Storage Devices Through the Internet
- 10. Use VPN to Access Your Network
- 11. Manage port forwarding and port triggering
- 12. Troubleshooting
- 13. Supplemental Information
- Quick Start
- Data Sheet
network lists. To turn off the SSID broadcast for the 2.4 GHz or 5 GHz guest WiFi
network, clear the Enable SSID Broadcast check box.
•
Allow guests to see each other and access my local network. By default, WiFi
clients that are connected to the 2.4 GHz or 5 GHz guest WiFi network cannot
access WiFi devices or Ethernet devices that are connected to the main WiFi
network. To allow access to the main WiFi network, select the Allow guests to
see each other and access my local network check box.
•
Guest Wireless Network Name (SSID). The SSID is the 2.4 GHz or 5 GHz guest
WiFi network name. The default 2.4 GHz SSID is NETGEAR_Guest. The default 5
GHz SSID NETGEAR-5G_Guest.
To change the SSID, enter a 32-character (maximum), case-sensitive name in this
field.
6.
Select a WiFi security option for the 2.4 GHz or 5 GHz guest WiFi network:
•
None. An open WiFi network that does not provide any security. Any WiFi device
can join the 2.4 GHz or 5 GHz guest WiFi network. This is the default setting for
the guest WiFi network.
•
WPA2-PSK [AES]. WPA2 provides a secure and fast connection but some older
WiFi devices do not detect WPA2 and support only WPA. Select WPA2-PSK [AES]
security to allow 802.11n devices to connect to the 2.4 GHz or 5 GHz guest WiFi
network at the fastest speed. If your network includes older devices that do not
support WPA2, select WPA-PSK [TKIP] + WPA2-PSK [AES] security. To use WPA2
security, in the Password (Network Key) field, enter a phrase of 8 to 63
characters. To join the 2.4 GHz or 5 GHz guest WiFi network, a user must enter
this password.
•
WPA-PSK [TKIP] + WPA2-PSK [AES]. This security type enables WiFi devices
that support either WPA or WPA2 to join the 2.4 GHz band of the guest WiFi
network. However, WPA-PSK [TKIP] is less secure than WPA2-PSK [AES] and limits
the speed of WiFi devices to 54 Mbps. To use WPA + WPA2 security, in the
Password (Network Key) field, enter a phrase of 8 to 63 characters. To join the
2.4 GHz or 5 GHz guest WiFi network, a user must enter this password.
•
WPA3-PSK. This security type enables WiFi devices that support WPA3 to join
the WiFi network. WPA3 is the latest security standard, uses SAE encryption, and
is more secure than WPA2. If all devices on your network support WPA3, we
recommend that you use this type of security.
•
WPA2 + WPA3. This security type enables WiFi devices that support either WPA2
or WPA3 to join the router’s WiFi network.
7. Click the Apply button.
Your settings are saved.
User Manual68Manage Network Settings
Nighthawk AX2400 WiFi 6 Router