User Manual
Table Of Contents
- Contents
- 1. Overview
- Orbi Router and Satellite Models
- Orbi Router and Satellite Hardware Overviews
- Orbi Router Model RBR50 Hardware Overview
- Orbi Satellite Model RBS50 Hardware Overview
- Orbi Router Model RBR40 Hardware Overview
- Orbi Satellite Model RBS40 Hardware Overview
- Orbi Router Model RBR20 Hardware Overview
- Orbi Satellite Model RBS20 Hardware Overview
- Orbi Wall Plug Satellite Model RBW30 Hardware Overview
- LED Behavior
- Connect Your Router
- Place Your Satellite
- Sync Your Orbi Satellite
- Set Up an Ethernet Backhaul Connection
- Download the NETGEAR Orbi App
- 2. Connect to the Network and Access the Router
- 3. Specify Your Internet Settings
- Use the Internet Setup Wizard
- Manually Set Up the Internet Connection
- Specify IPv6 Internet Connections
- Requirements for Entering IPv6 Addresses
- Use Auto Detect for an IPv6 Internet Connection
- Use Auto Config for an IPV6 Internet Connection
- Set Up an IPv6 6rd Tunnel Internet Connection
- Set Up an IPv6 6to4 Tunnel Internet Connection
- Set Up an IPv6 Pass Through Internet Connection
- Set Up an IPv6 Fixed Internet Connection
- Set Up an IPv6 DHCP Internet Connection
- Set Up an IPv6 PPPoE Internet Connection
- Change the MTU Size
- 4. Control Access to the Internet
- 5. Optimize Performance
- 6. Specify Network Settings
- View or Change WAN Settings
- Dynamic DNS
- Set Up a Default DMZ Server
- Change the Router’s Device Name
- Change the LAN TCP/IP Settings
- Use the Router as a DHCP Server
- Disable the DHCP Server Feature in the Router
- Manage Reserved LAN IP Addresses
- Custom Static Routes
- Specify Basic WiFi Settings
- Set Up a Guest WiFi Network
- View or Change Advanced WiFi Settings
- Use the Router as a WiFi Access Point
- Generate a New Backhaul Password
- Set Up a Bridge for a Port Group or VLAN Tag Group
- Enable British Telecom IGMP Proxy Support
- 7. Manage Your Network
- Update the Router and Satellite Firmware
- Change the admin Password
- Set Up Password Recovery
- Recover the admin Password
- View Router Status
- View Satellite Status
- View and Manage Logs of Router Activity
- View Devices Connected to the Network or Edit Device Information
- View Satellites Connected to the Network or Edit Satellite Information
- Manage the Orbi Outdoor Satellite LED Lighting
- Monitor Internet Traffic
- Manage the Router Configuration File
- Set Up Remote Management
- Use Remote Access
- Remotely Access Your Router Using the genie App
- 8. Customize Internet Traffic Rules for Ports
- 9. Use VPN to Access Your Network
- 10. Troubleshooting
- 11. Supplemental Information
For the VPN tunnel to work, the local LAN IP address of the remote router must use a different LAN IP
scheme from that of the local LAN where your VPN client computer is connected. If both networks use the
same LAN IP scheme, when the VPN tunnel is established, you cannot access your home router or your
home network with the OpenVPN software.
The default LAN IP address scheme for the router is 192.x.x.x.The most common IP schemes are 192.x.x.x,
172.x.x.x, and 10.x.x.x. If you experience a conflict, change the IP scheme either for your home network or
for the network with the client VPN computer. For information about changing these settings, see Change
the LAN TCP/IP Settings on page 68.
To open a VPN tunnel:
1. Launch the OpenVPN application with administrator privileges.
Figure 19.The OpenVPN icon displays in the Windows taskbar.
TIP:You can create a shortcut to the VPN program, then use the shortcut to access the settings and
select the run as administrator check box. Then every time you use this shortcut, OpenVPN
automatically runs with administrator privileges.
2. Right-click the OpenVPN icon.
3. Select Connect.
The VPN connection is established.You can launch a web browser and log in to your router.
Use VPN to Access Your Network
119
Orbi WiFi System