User Manual
Table Of Contents
- Contents
- 1. Overview
- Orbi Router and Satellite Models
- Orbi Router and Satellite Hardware Overviews
- Orbi Router Model RBR50 Hardware Overview
- Orbi Satellite Model RBS50 Hardware Overview
- Orbi Router Model RBR40 Hardware Overview
- Orbi Satellite Model RBS40 Hardware Overview
- Orbi Router Model RBR20 Hardware Overview
- Orbi Satellite Model RBS20 Hardware Overview
- Orbi Wall Plug Satellite Model RBW30 Hardware Overview
- LED Behavior
- Connect Your Router
- Place Your Satellite
- Sync Your Orbi Satellite
- Set Up an Ethernet Backhaul Connection
- Download the NETGEAR Orbi App
- 2. Connect to the Network and Access the Router
- 3. Specify Your Internet Settings
- Use the Internet Setup Wizard
- Manually Set Up the Internet Connection
- Specify IPv6 Internet Connections
- Requirements for Entering IPv6 Addresses
- Use Auto Detect for an IPv6 Internet Connection
- Use Auto Config for an IPV6 Internet Connection
- Set Up an IPv6 6rd Tunnel Internet Connection
- Set Up an IPv6 6to4 Tunnel Internet Connection
- Set Up an IPv6 Pass Through Internet Connection
- Set Up an IPv6 Fixed Internet Connection
- Set Up an IPv6 DHCP Internet Connection
- Set Up an IPv6 PPPoE Internet Connection
- Change the MTU Size
- 4. Control Access to the Internet
- 5. Optimize Performance
- 6. Specify Network Settings
- View or Change WAN Settings
- Dynamic DNS
- Set Up a Default DMZ Server
- Change the Router’s Device Name
- Change the LAN TCP/IP Settings
- Use the Router as a DHCP Server
- Disable the DHCP Server Feature in the Router
- Manage Reserved LAN IP Addresses
- Custom Static Routes
- Specify Basic WiFi Settings
- Set Up a Guest WiFi Network
- View or Change Advanced WiFi Settings
- Use the Router as a WiFi Access Point
- Generate a New Backhaul Password
- Set Up a Bridge for a Port Group or VLAN Tag Group
- Enable British Telecom IGMP Proxy Support
- 7. Manage Your Network
- Update the Router and Satellite Firmware
- Change the admin Password
- Set Up Password Recovery
- Recover the admin Password
- View Router Status
- View Satellite Status
- View and Manage Logs of Router Activity
- View Devices Connected to the Network or Edit Device Information
- View Satellites Connected to the Network or Edit Satellite Information
- Manage the Orbi Outdoor Satellite LED Lighting
- Monitor Internet Traffic
- Manage the Router Configuration File
- Set Up Remote Management
- Use Remote Access
- Remotely Access Your Router Using the genie App
- 8. Customize Internet Traffic Rules for Ports
- 9. Use VPN to Access Your Network
- 10. Troubleshooting
- 11. Supplemental Information
Quick Tips
This section describes tips for troubleshooting some common problems.
Sequence to Restart Your Network
When you restart your network, follow this sequence:
1. Turn off and unplug the modem.
2. Turn off the router.
3. Plug in the modem and turn it on. Wait two minutes.
4. Turn on the router and wait two minutes.
WiFi Settings
Make sure that the WiFi settings in the WiFi-enabled computer or mobile device and the router match.
The WiFi network name (SSID) and WiFi security settings must match exactly.
If you set up an access list, you must add each WiFi-enabled computer or mobile device’s MAC address to
the router’s access list.
Network Settings
Make sure that the network settings of the computer are correct.Wired and wirelessly connected computers
must use network (IP) addresses on the same network as the router. The simplest way to do this is to
configure each computer to obtain an IP address automatically using DHCP.
Some cable modem service providers require you to use the MAC address of the computer initially registered
on the account.You can view the MAC address on the Attached Devices page.
The Router and Satellite Do Not Sync
If you are experiencing difficulty syncing the router and the satellite, we recommend that you move the
satellite into the same room as the router during the sync. Then move the satellite to a different location.
To sync the router and the satellite:
1. Place the satellite in the same room as the Orbi router.
Use this satellite location only during the sync process.
2. Connect the satellite to a power source.
3. If the Power LED on the back of the satellite does not light, press the Power On/Off button.
4. Wait for the satellite’s ring LED to light solid white or magenta.
5. Press the Sync button on the router and then within two minutes, press the Sync button on the satellite.
The satellite’s ring LED pulses white, then lights one of the following colors for about three minutes and
then turns off:
Troubleshooting
123
Orbi WiFi System