Owner's Manual
Table Of Contents
- Contents
- 1. Overview
- 2. Connect to the Network and Access the Router
- 3. Specify Your Internet Settings
- Use the Setup Wizard
- Manually set up the Internet connection
- Requirements for entering IPv6 addresses
- Specify IPv6 Internet connections
- Use auto detection for an IPv6 Internet connection
- Use auto configuration for an IPv6 Internet connection
- Set up an IPv6 6rd tunnel Internet connection
- Set up an IPv6 6to4 tunnel Internet connection
- Set up an IPv6 pass-through Internet connection
- Set up an IPv6 fixed Internet connection
- Set up an IPv6 DHCP Internet connection
- Set up an IPv6 PPPoE Internet connection
- Change the MTU size
- 4. Control Access to the Internet
- Enable Circle smart parental controls
- Activate and manage NETGEAR Armor using the Orbi app
- Allow or block access to your network
- Use keywords to block Internet sites
- Delete keywords that are used to block Internet sites
- Avoid blocking on a trusted computer
- Block services from the Internet
- Manage network access control lists
- Schedule when to block Internet sites and services
- Set up security event email notifications
- 5. Optimize Performance
- 6. Specify Network Settings
- View or change WAN settings
- Manage Dynamic DNS
- Set up a default DMZ server
- Change the router’s device name
- Change the LAN TCP/IP settings
- Use the router as a DHCP server
- Disable the DHCP server feature in the router
- Manage reserved LAN IP addresses
- Manage custom static routes
- Specify basic WiFi settings
- Change the WiFi password or security level
- Set up a guest WiFi network
- View or change advanced WiFi settings
- Use the router as a WiFi access point
- Set up router mode
- Generate a new backhaul password
- Set up a bridge for a port group or VLAN tag group
- Enable British Telecom IGMP proxy support
- 7. Manage Your Network
- Update the router and satellite firmware
- Change the admin password
- Enable admin password reset
- Reset the admin password
- View router status and usage information
- Display Internet port statistics
- Check the Internet connection status
- View the satellite status
- View and manage logs of router activity
- View devices connected to the network or edit device information
- View satellites connected to the network or edit satellite information
- Manage the Orbi Outdoor Satellite LED lighting
- Monitor Internet traffic
- Set your time zone, adjust for daylight saving time, or change the NTP server
- Manage the router configuration file
- Set up remote management
- Use remote access
- Access your Orbi network from anywhere using the Orbi app
- 8. Customize Internet Traffic Rules for Ports
- 9. Use VPN to Access Your Network
- 10. Troubleshooting
- 11. Supplemental information
Table 6. Factory default settings for the router (Continued)
Default SettingFeature
EnabledWiFi communicationWiFi
See router labelSSID name
WPA2-PSK (AES)Security
EnabledBroadcast SSID
Auto
3
Transmission speed
United States in the US; otherwise,
varies by region
Country/region
2.4 GHz front and back haul: Auto
5 GHz front haul:
•
Channel 48 for NA, PR, AU, CA,
and TW
•
Channel 36 for EU, KO, JP, and
IN
5 GHz back haul:
•
Channel 157 for NA, PR, AU, CA,
and TW
•
Channel 108 for EU, KO, JP, and
IN
RF channel
3
Maximum wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput can vary. Network
conditions and environmental factors, including volume of network traffic, building materials and construction, and
network overhead, lower actual data throughput rate.
Factory settings for Orbi satellites
You can return the satellite to its factory settings. Use the end of a paper clip or a similar
object to press and hold the Reset button on the back of the satellite for at least seven
seconds. The satellite resets, and returns to the factory settings.
Factory settings for Orbi satellite model RBS50
The following table shows the factory default settings for the satellite.
User Manual147Supplemental information
Orbi WiFi System