User Manual
Table Of Contents
- Contents
- 1. Hardware Setup
- 2. Connect to the Router’s Network and Automatically Set Up the Internet Connection
- 3. Specify Your Internet Settings
- Use the Internet Setup Wizard
- Manually set up the Internet connection
- Specify IPv6 Internet connections
- Requirements for entering IPv6 addresses
- Use Auto Detect for an IPv6 Internet connection
- Set up an IPv6 6to4 tunnel Internet connection
- Set up an IPv6 pass-through Internet connection
- Set up a fixed IPv6 Internet connection
- Set up an IPv6 DHCP Internet connection
- Set up an IPv6 PPPoE Internet connection
- Use Auto Config for an IPv6 Internet connection
- Set up an IPv6 6rd tunnel connection
- Manage the MTU size
- 4. Control Access to the Internet
- Manage NETGEAR Armor
- Activate Armor using the Nighthawk app
- View or change your NETGEAR Armor settings using the Nighthawk app
- View or change your NETGEAR Armor settings from the Armor portal
- Sign in to NETGEAR Armor from the router web interface and start your subscription
- Access the NETGEAR Armor portal from the router web interface
- Disable or Reenable NETGEAR Armor from the router web interface
- Enable Circle with Disney
- Enable access control to allow or block access to the Internet
- Manage network access control lists
- Use keywords to block Internet sites
- Delete keywords from the blocked list
- Prevent blocking on a trusted computer
- Block services from the Internet
- Schedule when to block Internet sites and services
- Set up security event email notifications
- Manage NETGEAR Armor
- 5. Optimize Performance
- 6. Manage Network Settings
- View or change the WAN settings
- Set up a default DMZ server
- Change the LAN TCP/IP settings
- Change the router’s device name
- Specify the IP addresses that the router assigns
- Disable the DHCP server feature in the router
- Manage reserved LAN IP addresses
- Set up the router as a WiFi access point
- Set up the router in bridge mode
- Return the router to router mode
- Set up a bridge for a port group or VLAN tag group
- Manage custom static routes
- 7. Manage the WiFi Network Settings
- Use the WPS Wizard for WiFi connections
- Specify basic WiFi settings
- Change the WiFi password or the WiFi security
- Set up WPA/WPA2 enterprise WiFi security
- Set up WEP legacy WiFi security
- Change the WiFi Mbps settings
- Change the transmission power of the WiFi radios
- Set up a guest WiFi network
- Control the WiFi radios
- Set up a WiFi schedule
- Manage WPS settings
- Enable or disable implicit beamforming
- Enable or disable airtime fairness
- Enable or disable MU-MIMO
- Manage advanced WiFi settings
- 8. Manage Your Router
- Update the router firmware
- Change the admin password
- Enable admin password recovery
- Recover the admin password
- Manage the router configuration file
- View information about the router and the Internet and WiFi settings
- Display the statistics of the Internet port
- Check the Internet connection status
- View and manage logs of router activity
- View devices currently on the network
- Monitor, meter, and control Internet traffic
- Set your time zone
- Change the NTP server
- Disable LED blinking or turn off LEDs
- Return the router to its factory default settings
- 9. Share USB Storage Devices Attached to the Router
- USB device requirements
- Connect a USB storage device to the router
- Access a storage device connected to the router
- Back up Windows-based computers with ReadySHARE Vault
- Enable FTP access within your network
- View network folders on a storage device
- Add a network folder on a USB storage device
- Edit a network folder on a USB storage device
- Approve a USB storage device
- Remotely access a USB device using ReadyCLOUD
- Safely remove a USB storage device
- 10. Use VPN to Access Your Network
- Set up a VPN connection
- Manage Dynamic DNS for VPN connections
- Enable and configure OpenVPN on the router
- Install OpenVPN software
- Install the OpenVPN client utility and VPN configuration files on a Windows-based computer
- Install the OpenVPN client utility and VPN configuration files on a Mac
- Install the OpenVPN client utility and VPN configuration files on an iOS device
- Install the OpenVPN client utility and VPN configuration files on an Android device
- LAN requirements for VPN connections
- Use a VPN tunnel on a Windows-based computer
- Use VPN to access your Internet service at home
- 11. Manage Port Forwarding and Port Triggering Traffic Rules
- 12. Troubleshooting
- A. Supplemental Information
If you disabled the router’s SSID broadcast, then your WiFi network is hidden and
does not display in your WiFi client’s scanning list. (By default, SSID broadcast is
enabled.)
•
Does your WiFi device support the security that you are using for your WiFi network
(WPA, WPA2, WPA and WPA2 enterprise security, or WEP)?
•
If you want to view the WiFi settings for the router, use an Ethernet cable to connect
a computer to a LAN port on the router. Then log in to the router, and select
BASIC > Wireless.
Note: Be sure to click the Apply button if you change settings.
If your WiFi device finds your network but the signal strength is weak, check these
conditions:
•
Is your router too far from your computer or too close? Place your computer near
the router but at least 6 feet (1.8 meters) away and see whether the signal strength
improves.
•
Are objects between the router and your computer blocking the WiFi signal?
Troubleshoot your network using the ping
utility
Most network devices and routers contain a ping utility that sends an echo request
packet to the designated device. The device then responds with an echo reply. You can
easily troubleshoot a network using the ping utility in your computer or workstation.
Test the LAN path to your router
You can ping the router from your computer to verify that the LAN path to your router
is set up correctly.
To ping the router from a Windows-based computer:
1. From the Windows toolbar, click the Start button and select Run.
2.
In the field provided, type ping followed by the IP address of the router, as in this
example:
ping www.routerlogin.net
3. Click the OK button.
You see a message like this one:
User Manual178Troubleshooting
Nighthawk AC2300 Cybersecurity WiFi Router Model RS400