User Manual
Table Of Contents
- Contents
- 1. Hardware Setup
- 2. Connect to the Router’s Network and Automatically Set Up the Internet Connection
- 3. Specify Your Internet Settings
- Use the Internet Setup Wizard
- Manually set up the Internet connection
- Specify IPv6 Internet connections
- Requirements for entering IPv6 addresses
- Use Auto Detect for an IPv6 Internet connection
- Set up an IPv6 6to4 tunnel Internet connection
- Set up an IPv6 pass-through Internet connection
- Set up a fixed IPv6 Internet connection
- Set up an IPv6 DHCP Internet connection
- Set up an IPv6 PPPoE Internet connection
- Use Auto Config for an IPv6 Internet connection
- Set up an IPv6 6rd tunnel connection
- Manage the MTU size
- 4. Control Access to the Internet
- Manage NETGEAR Armor
- Activate Armor using the Nighthawk app
- View or change your NETGEAR Armor settings using the Nighthawk app
- View or change your NETGEAR Armor settings from the Armor portal
- Sign in to NETGEAR Armor from the router web interface and start your subscription
- Access the NETGEAR Armor portal from the router web interface
- Disable or Reenable NETGEAR Armor from the router web interface
- Enable Circle with Disney
- Enable access control to allow or block access to the Internet
- Manage network access control lists
- Use keywords to block Internet sites
- Delete keywords from the blocked list
- Prevent blocking on a trusted computer
- Block services from the Internet
- Schedule when to block Internet sites and services
- Set up security event email notifications
- Manage NETGEAR Armor
- 5. Optimize Performance
- 6. Manage Network Settings
- View or change the WAN settings
- Set up a default DMZ server
- Change the LAN TCP/IP settings
- Change the router’s device name
- Specify the IP addresses that the router assigns
- Disable the DHCP server feature in the router
- Manage reserved LAN IP addresses
- Set up the router as a WiFi access point
- Set up the router in bridge mode
- Return the router to router mode
- Set up a bridge for a port group or VLAN tag group
- Manage custom static routes
- 7. Manage the WiFi Network Settings
- Use the WPS Wizard for WiFi connections
- Specify basic WiFi settings
- Change the WiFi password or the WiFi security
- Set up WPA/WPA2 enterprise WiFi security
- Set up WEP legacy WiFi security
- Change the WiFi Mbps settings
- Change the transmission power of the WiFi radios
- Set up a guest WiFi network
- Control the WiFi radios
- Set up a WiFi schedule
- Manage WPS settings
- Enable or disable implicit beamforming
- Enable or disable airtime fairness
- Enable or disable MU-MIMO
- Manage advanced WiFi settings
- 8. Manage Your Router
- Update the router firmware
- Change the admin password
- Enable admin password recovery
- Recover the admin password
- Manage the router configuration file
- View information about the router and the Internet and WiFi settings
- Display the statistics of the Internet port
- Check the Internet connection status
- View and manage logs of router activity
- View devices currently on the network
- Monitor, meter, and control Internet traffic
- Set your time zone
- Change the NTP server
- Disable LED blinking or turn off LEDs
- Return the router to its factory default settings
- 9. Share USB Storage Devices Attached to the Router
- USB device requirements
- Connect a USB storage device to the router
- Access a storage device connected to the router
- Back up Windows-based computers with ReadySHARE Vault
- Enable FTP access within your network
- View network folders on a storage device
- Add a network folder on a USB storage device
- Edit a network folder on a USB storage device
- Approve a USB storage device
- Remotely access a USB device using ReadyCLOUD
- Safely remove a USB storage device
- 10. Use VPN to Access Your Network
- Set up a VPN connection
- Manage Dynamic DNS for VPN connections
- Enable and configure OpenVPN on the router
- Install OpenVPN software
- Install the OpenVPN client utility and VPN configuration files on a Windows-based computer
- Install the OpenVPN client utility and VPN configuration files on a Mac
- Install the OpenVPN client utility and VPN configuration files on an iOS device
- Install the OpenVPN client utility and VPN configuration files on an Android device
- LAN requirements for VPN connections
- Use a VPN tunnel on a Windows-based computer
- Use VPN to access your Internet service at home
- 11. Manage Port Forwarding and Port Triggering Traffic Rules
- 12. Troubleshooting
- A. Supplemental Information
Pinging <IP address > with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
Request timed out
If the path is not functioning correctly, one of the following problems might be occurring:
•
Wrong physical connections
For a wired connection, make sure that the numbered LAN port LED is lit for the port
to which you are connected.
Check to see that the appropriate LEDs are lit for your network devices. If your router
and computer are connected to a separate Ethernet switch, make sure that the link
LEDs are lit for the switch ports that are connected to your computer and router.
•
Wrong network configuration
Verify that the Ethernet card driver software and TCP/IP software are both installed
and configured on your computer.
Verify that the IP address for your router and your computer are correct and that the
addresses are on the same subnet.
Test the path from a Windows-based computer to a remote
device
To test the path from a Windows-based computer to a remote device:
1. From the Windows toolbar, click the Start button and select Run.
2. In the Windows Run window, type
ping -n 10 <IP address>
where <IP address> is the IP address of a remote device such as your ISP DNS server.
If the path is functioning correctly, messages display that are similar to those shown
in Test the LAN path to your router on page 178.
3.
If you do not receive replies, check the following:
•
Check to see that IP address of your router is listed as the default gateway for
your computer. If DHCP assigns the IP configuration of your computers, this
information is not visible in your computer Network Control Panel. Verify that the
IP address of the router is listed as the default gateway.
•
Check to see that the network address of your computer (the portion of the IP
address specified by the subnet mask) is different from the network address of
the remote device.
User Manual179Troubleshooting
Nighthawk AC2300 Cybersecurity WiFi Router Model RS400