User Manual
Table Of Contents
- Contents
- 1. Hardware Setup
- 2. Connect to the Router’s Network and Automatically Set Up the Internet Connection
- 3. Specify Your Internet Settings
- Use the Internet Setup Wizard
- Manually set up the Internet connection
- Specify IPv6 Internet connections
- Requirements for entering IPv6 addresses
- Use Auto Detect for an IPv6 Internet connection
- Set up an IPv6 6to4 tunnel Internet connection
- Set up an IPv6 pass-through Internet connection
- Set up a fixed IPv6 Internet connection
- Set up an IPv6 DHCP Internet connection
- Set up an IPv6 PPPoE Internet connection
- Use Auto Config for an IPv6 Internet connection
- Set up an IPv6 6rd tunnel connection
- Manage the MTU size
- 4. Control Access to the Internet
- Manage NETGEAR Armor
- Activate Armor using the Nighthawk app
- View or change your NETGEAR Armor settings using the Nighthawk app
- View or change your NETGEAR Armor settings from the Armor portal
- Sign in to NETGEAR Armor from the router web interface and start your subscription
- Access the NETGEAR Armor portal from the router web interface
- Disable or Reenable NETGEAR Armor from the router web interface
- Enable Circle with Disney
- Enable access control to allow or block access to the Internet
- Manage network access control lists
- Use keywords to block Internet sites
- Delete keywords from the blocked list
- Prevent blocking on a trusted computer
- Block services from the Internet
- Schedule when to block Internet sites and services
- Set up security event email notifications
- Manage NETGEAR Armor
- 5. Optimize Performance
- 6. Manage Network Settings
- View or change the WAN settings
- Set up a default DMZ server
- Change the LAN TCP/IP settings
- Change the router’s device name
- Specify the IP addresses that the router assigns
- Disable the DHCP server feature in the router
- Manage reserved LAN IP addresses
- Set up the router as a WiFi access point
- Set up the router in bridge mode
- Return the router to router mode
- Set up a bridge for a port group or VLAN tag group
- Manage custom static routes
- 7. Manage the WiFi Network Settings
- Use the WPS Wizard for WiFi connections
- Specify basic WiFi settings
- Change the WiFi password or the WiFi security
- Set up WPA/WPA2 enterprise WiFi security
- Set up WEP legacy WiFi security
- Change the WiFi Mbps settings
- Change the transmission power of the WiFi radios
- Set up a guest WiFi network
- Control the WiFi radios
- Set up a WiFi schedule
- Manage WPS settings
- Enable or disable implicit beamforming
- Enable or disable airtime fairness
- Enable or disable MU-MIMO
- Manage advanced WiFi settings
- 8. Manage Your Router
- Update the router firmware
- Change the admin password
- Enable admin password recovery
- Recover the admin password
- Manage the router configuration file
- View information about the router and the Internet and WiFi settings
- Display the statistics of the Internet port
- Check the Internet connection status
- View and manage logs of router activity
- View devices currently on the network
- Monitor, meter, and control Internet traffic
- Set your time zone
- Change the NTP server
- Disable LED blinking or turn off LEDs
- Return the router to its factory default settings
- 9. Share USB Storage Devices Attached to the Router
- USB device requirements
- Connect a USB storage device to the router
- Access a storage device connected to the router
- Back up Windows-based computers with ReadySHARE Vault
- Enable FTP access within your network
- View network folders on a storage device
- Add a network folder on a USB storage device
- Edit a network folder on a USB storage device
- Approve a USB storage device
- Remotely access a USB device using ReadyCLOUD
- Safely remove a USB storage device
- 10. Use VPN to Access Your Network
- Set up a VPN connection
- Manage Dynamic DNS for VPN connections
- Enable and configure OpenVPN on the router
- Install OpenVPN software
- Install the OpenVPN client utility and VPN configuration files on a Windows-based computer
- Install the OpenVPN client utility and VPN configuration files on a Mac
- Install the OpenVPN client utility and VPN configuration files on an iOS device
- Install the OpenVPN client utility and VPN configuration files on an Android device
- LAN requirements for VPN connections
- Use a VPN tunnel on a Windows-based computer
- Use VPN to access your Internet service at home
- 11. Manage Port Forwarding and Port Triggering Traffic Rules
- 12. Troubleshooting
- A. Supplemental Information
The UPnP page displays.
5. Select the Turn UPnP On check box.
By default, this check box is selected. UPnP for automatic device configuration can
be enabled or disabled. If the Turn UPnP On check box is cleared, the router does
not allow any device to automatically control router resources, such as port
forwarding.
6. Type the advertisement period in minutes.
The advertisement period specifies how often the router broadcasts its UPnP
information. This value can range from 1 to 1440 minutes. The default period is 30
minutes. Shorter durations ensure that control points receive current device status
at the expense of more network traffic. Longer durations can compromise the
freshness of the device status but can significantly reduce network traffic.
7. Type the advertisement time to live in hops.
The time to live for the advertisement is measured in hops (steps) for each UPnP
packet sent. Hops are the steps a packet takes between routers. The number of hops
can range from 1 to 255. The default value for the advertisement time to live is 4
hops, which should be fine for most home networks. If you notice that some devices
are not being updated or reached correctly, it might be necessary to increase this
value.
8. Click the Apply button.
The UPnP Portmap Table displays the IP address of each UPnP device that is accessing
the router and which ports (internal and external) that device opened. The UPnP
Portmap Table also displays what type of port is open and whether that port is still
active for each IP address.
To refresh the information in the UPnP Portmap Table, click the Refresh button.
Enable or disable Smart Connect
Smart Connect selects the fastest WiFi band for your device. For Smart Connect to work,
the 2.4 GHz and 5 GHz bands must use the same WiFi network name (SSID) and network
key (password). That means that when you connect to the router with WiFi, you see only
one SSID that connects to both bands.
Note: If you enable Smart Connect and the SSID and passwords for the 2.4 GHz and
5 GHz bands do not match, the WiFi settings for 2.4 GHz band overwrites the WiFi
settings for 5 GHz band.
User Manual64Optimize Performance
Nighthawk AC2300 Cybersecurity WiFi Router Model RS400