User's Manual

ManualsBrandsNETGEAR ManualsOtherWG111U

Table Of Contents

User’s Manual for the NETGEAR Super AG Wireless USB 2.0 Adapter WG111U
Technical Support
Statement of Conditions
FCC Information to User
Regulatory Compliance Information
Export Restrictions
Europe - EU Declaration of Conformity
Requirements For Operation in the European Community
Canadian Department of Communications Radio Interference Regulations
Chapter 1 About This Manual
- Audience, Scope, Conventions
  - Table 1. Typographical conventions
  - Table 1-1. Manual Specifications
- How to Use this Manual
  - Figure 1-1: HTML version of this manual
- How to Print this Manual
Chapter 2 Introduction
- About the WG111U
- Key Features
  - 802.11a and 802.11b/g Wireless Networking
- Comparing the 802.11a, 802.11b, and 802.11g Modes
  - Table 2-1. Comparison of Wireless Modes
- What’s in the Box?
- A Road Map for ‘How to Get There From Here’
Chapter 3 Basic Setup
- What You Need Before You Begin
- Two Basic Operating Modes
- WG111U Default Wireless Configuration Settings
- Basic Installation Instructions
  - For Windows XP Users Installing a WG111U
  - For Windows 2000, ME, and 98SE Users Installing a WG111U
- WG111U Wireless Connection Indicators
  - Interpreting the LED on the WG111U
    - Table 3-1: LED Descriptions
  - Interpreting System Tray Icon Colors
Chapter 4 Configuration
- Understanding the Configuration Options
- Using Configuration Profiles
  - Connecting to an Access Point in Infrastructure Mode
  - How to Configure an Infrastructure Mode Profile
    - Figure 4-1: Settings page
- Connecting to Another PC in Ad-hoc Mode
  - How to Configure an Ad-hoc Mode Profile
    - Figure 4-2: Settings page
    - Figure 4-3: Ad-Hoc Setting dialog box
- What’s on the Statistics Page?
  - Figure 4-4: Statistics page
- Understanding the Advanced Settings Page
  - Figure 4-5: Advanced Settings page
  - European Regulatory Requirements for Transmit Power Control
Chapter 5 Wireless Security Configuration
- Understanding the Security Options
- Using WEP Security
- Using WPA-PSK Advanced Security
Chapter 6 Troubleshooting
- Basic Tips
- Frequently Asked Questions
  - General Questions
Appendix A Technical Specifications
Appendix B Wireless Networking Basics
- Wireless Networking Overview
- WEP Wireless Security
- WPA Wireless Security
- Appendix C Preparing Your Network to Work with a Router
What You Need To Use a Router with a Broadband Modem
- Cabling and Computer Hardware
- Computer Network Configuration Requirements
- Internet Configuration Requirements
- Where Do I Get the Internet Configuration Parameters?
- Record Your Internet Connection Information
Preparing Your Computers for TCP/IP Networking
Configuring Windows 95, 98, and Me for TCP/IP Networking
- Installing or Verifying Windows Networking Components
- Enabling DHCP to Automatically Configure TCP/IP Settings in Windows 95B, 98, and Me
- Selecting the Windows’ Internet Access Method
- Verifying TCP/IP Properties
Configuring Windows NT4, 2000 or XP for IP Networking
- Installing or Verifying Windows Networking Components
- Configuring DHCP of TCP/IP in Windows XP, 2000, or NT4
- DHCP Configuration of TCP/IP in Windows XP
- DHCP Configuration of TCP/IP in Windows 2000
- DHCP Configuration of TCP/IP in Windows NT4
- Verifying TCP/IP Properties for Windows XP, 2000, and NT4
Configuring the Macintosh for TCP/IP Networking
- MacOS 8.6 or 9.x
- MacOS X
- Verifying TCP/IP Properties for Macintosh Computers
Verifying the Readiness of Your Internet Account
- Are Login Protocols Used?
- What Is Your Configuration Information?
- Obtaining ISP Configuration Information for Windows Computers
- Obtaining ISP Configuration Information for Macintosh Computers
Restarting the Network
Glossary
Index

User’s Manual for the NETGEAR Super AG Wireless USB 2.0 Adapter WG111U

5-4 Wireless Security Configuration

202-10065-01

How to Configure WEP Encryption Security

Follow the steps below to configure WEP Encryption Security.

1. Run the WG111U Smart Wireless Wizard.

a. Make sure the WG111U software is installed and the WG111U is fully inserted in the USB

port of your PC.

b. Open the configuration utility by clicking on the WG111U icon on the Windows

desktop or in the system tray. The Settings page opens.

2. Configure the Network Name (SSID) settings.

Enter the SSID. This is also called the Wireless Network Name.

Tip: Click the Networks tab to view a list of the available wireless networks and their SSIDs.

3. Configure the WEP settings.

a. Select the WEP radio button.

Figure 5-1: WEP settings screen