WN2000RPT WiFi Range Extender Installation Guide
Getting Started The NETGEAR WiFi Range Extender increases the distance of a WiFi network by boosting the existing WiFi signal and enhancing the overall signal quality over long distances. An extender repeats the signals from an existing WiFi router or access point. WiFi Range Extender Boosts the range of your existing WiFi and creates a stronger signal in hard-to-reach areas. Existing WiFi Sometimes your router does not provide the WiFi coverage you need.
Meet Your Extender Before you install your extender, familiarize yourself with its LEDs, buttons, and ports.
Rear Panel Restore Factory Settings button Ethernet ports Power input Power On/Off button 4
LED Descriptions Use the LEDs during installation to find the best location for the extender or to monitor the extender performance. Link Rate LED Status LED This LED indicates the connection between the extender and the router or access point. • Solid green. Best connection. • Solid yellow. Good connection. • Solid red. Poor connection. • Off. No connection. • Solid green. The extender is powered on. • Off. The extender is powered off.
Install the Extender Place the extender, apply power, and connect it to your WiFi network. Place the Extender and Apply Power 1. Place your extender in the same room as your WiFi router. Note: Proximity to the WiFi router is required only during the initial setup process. 2. Plug the extender into an electrical outlet. lights green. If the Status LED does not The Status LED light, press the Power button.
Connect with WPS Wi-Fi Protected Setup (WPS) lets you easily join a secure WiFi network without typing the network name and password. WPS does not support WEP network security. If you are using WEP security, follow the instructions in Connect with NETGEAR genie Smart Setup on page 9. To connect with WPS: 1. Press the WPS button on the extender. 2. Within two minutes, press the WPS button on your router or access point.
3. Find the new extender network name. The extender’s wireless network name (SSID) changes to your existing WiFi network name, with _EXT at the end of the name. For example: • Existing WiFi network name. MyNetworkName • New extender network name. MyNetworkName_EXT 4. Connect your existing WiFi devices to the new extender network (MyNetworkName_EXT). Use the same WiFi password that you use for your WiFi router. 5. Unplug the extender and move it to a new location closer to the area with a poor WiFi signal.
Connect with NETGEAR genie Smart Setup 1. Use a WiFi network manager on a computer or mobile device to find and connect to the NETGEAR_EXT (SSID) WiFi network. After the connection with the computer or mobile device is established, the Device to Extender LED lights solid green.
2. Open a web browser window from the same computer or mobile device. The browser takes you directly to the NETGEAR genie® smart setup. Note: If you are not automatically directed to NETGEAR genie, launch a web browser and type www.mywifiext.net in the address field. Enter admin for the user name and password for the password. 3. Select a WiFi network to extend and click the Continue button.
4. Type the network passphrase (also called a password or security key) in the PassPhrase field and click the Continue button. 5. Type the name (SSID) for your extender wireless network in the 2.4GHz Network Name (SSID) field and click the Continue button. Note: You can use the same security settings as your existing network by selecting the check box.
The settings are applied and the following screen displays: 6. Use a WiFi network manager on the computer or mobile device to connect to the extender’s newly created WiFi network. Repeat this step for all of your computers and mobile devices.
7. Select the check box and click the Continue button. 8. Click the Finish button.
9. Unplug the extender and move it to a new location closer to an area with a poor WiFi signal. The location that you choose must be within the range of your existing WiFi router network. DO DON’T 10. Plug the extender into an electrical outlet. lights green. If the Status LED does not The Status LED light, press the Power button. Use the Link Rate LED on the front panel to help you choose a spot where the extender-to-router connection is optimal.
Connect Ethernet-Enabled Devices After the extender is connected to your existing WiFi network, you can use the extender to connect up to four devices wirelessly to your WiFi router or access point.
To connect an Ethernet-enabled device to your WiFi router or access point: 1. Set up the extender. For more information, see Place the Extender and Apply Power on page 6. 2. Connect the extender to an existing WiFi network. For more information, see Connect to an Existing WiFi Network on page 6. 3. Plug the Ethernet cable from an Ethernet-enabled device to an Ethernet port on the extender. The Ethernet-enabled device connects to the router or access point.
Access the Extender Settings After installation, you can log in to the extender to view or change the extender’s settings. To log in to the extender after the initial setup: 1. Connect a computer or mobile device to the extender’s network. 2. Launch a web browser and type www.mywifiext.net or www.mywifiext.com in the address field. A login screen displays. 3. Enter admin for the user name and password for the password.
Frequently Asked Questions You can find more information about your product in the user manual, which is available at http://support.netgear.com. The web browser setup guide keeps asking me for my network security key (passphrase), and I am sure I have entered the correct passphrase. What can I do? The extender is probably placed at the borderline of the range covered by the router or access point. For more information, see Place the Extender and Apply Power on page 6.
Will the extender work if I connect it to the router with an Ethernet cable? No. The extender is designed to connect wirelessly to the router or access point. What are the user name and password to log in to the extender? The user name is admin, and the default password is password. Both are case-sensitive. How do I restore the extender to its factory default settings? 1.
Support Thank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website. For product updates and web support, visit http://support.netgear.com. NETGEAR recommends that you use only the official NETGEAR support resources.
