Installation Guide N600 WiFi Range Extender Model WN2500RP
Contents Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Meet Your Extender. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 LED Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Install the WiFi Extender . . . .
Getting Started The NETGEAR WiFi Range Extender increases the distance of a WiFi network by boosting the existing WiFi signal and enhancing the overall signal quality over long distances. An extender repeats the signals from an existing WiFi router or access point. WiFi Range Extender Boosts the range of your existing WiFi and creates a stronger signal in hard-to-reach areas. Existing WiFi Sometimes your router does not provide the WiFi coverage you need.
Meet Your Extender Before you install your extender, familiarize yourself with its LEDs, buttons, and ports. Front Panel WPS button WPS LED LAN LEDs 1–4 Device to Extender LED 5 GHz Link Rate LED 2.
Rear Panel Restore Factory Settings button LAN ports 1–4 Power input Power On/Off button 5
LED Descriptions Use the LEDs during installation to find the best location for the extender or to monitor the extender performance. Power LED • Solid Amber. The extender is booting. • Solid Green. The extender is powered on. • Blinking Green. The firmware is corrupt. Visit http://support.netgear.com/. • Blinking Amber. The firmware is upgrading or the Restore Factory Settings button was pressed. • Off. The extender is powered off. 2.4 GHz Link This LED indicates a 2.
5 GHz Link Rate LED This LED indicates a 5 GHz WiFi connection between the extender and the router or access point. • Solid Green. Best connection • Solid Amber. Good connection • Solid Red. Poor connection • Off. No connection Device to Extender LED • Solid Green. The extender is connected to a computer or mobile device. • Off. The extender is not connected to a computer or mobile device. LAN LEDs WPS LED • Solid Green. The LAN port detects a local area network (LAN) connection. • Off.
Install the WiFi Extender Place the extender, apply power, and connect it to your WiFi network. Place the Extender and Apply Power 1. Place your extender in the same room as your WiFi router. Note: Proximity to the WiFi router is required only during the initial setup process. 2. Connect the power adapter to the extender and plug it into an electrical outlet. The Power LED lights solid amber while it is booting and then solid green when it is powered on.
Connect with WPS Wi-Fi Protected Setup (WPS) lets you easily join a secure WiFi network without typing the network name and password. WPS does not support WEP network security. If you are using WEP security, follow the instructions in Connect with NETGEAR genie Smart Setup on page 11. 1. Press the WPS button on the extender. The WPS LED blinks. 2. Within two minutes, press the WPS button on your router or access point. The WPS LED and the 2.
The extender’s wireless network name (SSID) changes to your existing WiFi network name, with _2GEXT or _5GEXT at the end of the name, depending on whether the extender is connecting to your WiFi network in 2.4 GHz or 5 GHz. For example: • Existing WiFi network name. MyNetworkName • New extender network name. MyNetworkName_2GEXT or MyNetworkName_5GEXT 5. Connect your WiFi devices to the new extender network. Use the same WiFi password that you use for your WiFi router. 6.
Connect with NETGEAR genie Smart Setup 1. Use a WiFi network manager on a computer or mobile device to find and connect to the NETGEAR_EXT (SSID) WiFi network. After the connection with the computer or mobile device is established, the Device to Extender LED lights solid green. 2. Open a web browser window from the same computer or mobile device. The browser takes you directly to the NETGEAR genie smart setup. Note: If you are not automatically directed to NETGEAR genie, launch a web browser and type www.
4. Type the network password (also called passphrase or security key) in the Password (network key) field and click the Continue button. 5. Select a 5 GHz WiFi network and click the Continue button. If your router does not support the 5 GHz band, click the Skip button. 6. Type the network password (also called passphrase or security key) in the Password (network key) field and click the Continue button.
7. Type the name (SSID) for your new extender WiFi network in the 2.4GHz Network Name (SSID) field and the 5GHz Network Name (SSID) field and click the Continue button. Note: To use the same security settings as your existing network, select the check box. The settings are applied and the following screen displays: 8. Use a WiFi network manager on the computer or mobile device to connect to the extender’s newly created WiFi network.
Repeat this step for all of your computers and mobile devices. 9. Select the check box and click the Continue button. 10. Unplug the extender and move it to a new location closer to the area with a poor WiFi signal. The location you choose must be within the range of your existing WiFi router network. 11. Plug the extender into an electrical outlet. The Power LED lights solid amber while it is booting and then solid green when it is powered on. If the Power LED does not light, press the Power button.
Connect Ethernet-Enabled Devices After the extender is connected to your existing WiFi network, you can connect a device to the extender using an Ethernet cable. Then that device can access your existing network through the extenderto-router WiFi connection. Blu-ray player TV Gaming console Extender WiFi router 1. Set up the extender and connect it to an existing WiFi network. For more information, see Install the WiFi Extender on page 8. 2.
Access Extender Settings After installation, you can log in to the extender to view or change the extender’s settings. 1. Connect a computer or mobile device to the extender’s network. 2. Launch a web browser and enter www.mywifiext.net or www.mywifiext.com in the address field. A login screen displays. 3. Enter admin for the user name and password for the password.
Frequently Asked Questions You can find more information about your product in the user manual, which is available at http://support.netgear.com. The web browser setup guide keeps asking me for my network security key (password), and I am sure I have entered the correct password. What can I do? The extender is probably placed at the borderline of the range covered by the router or access point. For more information, see Place the Extender and Apply Power on page 8.
Will the extender work if I connect it to the router with an Ethernet cable? No. The extender is designed to connect wirelessly to the router or access point. What are the user name and password to log in to the extender? The user name is admin and the default password is password. Both are case-sensitive. How do I restore the extender to its factory default settings? 1.
I enabled a wireless MAC filter (wireless access control or ACL) on my router. What should I do when installing the extender? When the wireless device connects through the extender to your router, the MAC address of the wireless device shown on the router is translated to another MAC address. If your router’s MAC filter is enabled, the wireless device connects to the extender but cannot get an IP address from the extender and cannot access the Internet.
Support Thank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website. For product updates and web support, visit http://support.netgear.com. NETGEAR recommends that you use only the official NETGEAR support resources.
