802.
FCC Certifications Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
CE Mark Warning This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class B for ITE, the essential protection requirement of Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Company has an on-going policy of upgrading its products and it may be possible that information in this document is not up-to-date. Please check with your local distributors for the latest information.
Table of Contents Unpacking Information ············································································1 Introduction To Wireless Router ······························································2 General Description ················································································2 Key Features ························································································3 The Front Panel ·············································································
LAN Interface Setup ···································································25 WAN Interface Setup ··································································26 Static IP Mode···························································································26 Firewall Configuration ····································································30 Port Filtering ··············································································30 IP filtering·······················
Unpacking Information Thank you for purchasing the product. Before you start, please check all the contents of this package. The product package should include the following: 1. 2. 3. 4.
Introduction To Wireless Router General Description The Wireless Router built-in with 4-port 10/100Mbps Fast Ethernet Switch is the latest generation of Wireless router product for Home/Office and SOHO users. This full-feature and self-contained compact Wireless Router will be fully for broadband access in both of LAN and Wireless environment.
Key Features The switch provides the following key features: n n n n n n n n n n n n n n n n n n n n Complies with IEEE 802.11b/g wireless standards Provides one 802.11b/g wireless Reverse SMA detachable antenna High speed transfer data rate up to 54Mbps Supports turbo mode for 72Mbps data transfer Supports wireless data encryption with 64/128-bit WEP, WPA (TKIP with IEEE 802.
The Front Panel The front panel of the Wireless Router is shown below. System LEDs System LED indicators locate on the front panel for showing the operating status of the whole device. l PWR (Power) LED This indicator lights green when the Wireless Router is receiving power; otherwise, it is off. l Status LED The LED will be dark for a few seconds when the system is started. After that, the LED will blink periodically to show the Wireless Router is working normally.
Port LEDs (LAN) Port LEDs (LAN) indicators locate on the front panel for showing the operating status of 10/100Mbps Fast Ethernet switching ports. l Act/Link LED Every port has a Act/Link LED. Steady green (link state) indicates that the port has good linkage to its associated devices. Flashing green indicates that the port is receiving or transmitting data between its associated devices.
Wall-mount option Before attach this router on the wall, you have to finish the desktop option steps first. 1. Select a location with access for cables and a power outlet. 2. Unplug the unit. Place it upside down on a flat surface and mark the two holes for anchors. 3. Installing the Wall mount anchor (plastic) into the wall with tools such as drill or hammer. 4. Insert the provided screws in each hole of the stand parts. 5. Attaches the unit to the anchors on the wall. Stand Option 1.
Installing And Using Wireless Router This Chapter provides a step-by-step guide to the installation and configuration of the Wireless Router. We suggest you go over the whole chapter and then do more advanced operation. Network configuration setup Steps to build up the network: Ø Connect the ADSL or Cable modem to the Ethernet WAN port on the back of the Wireless Router by using the UTP cable.
Computer configuration setup In order to communicate with this Wireless Router, you have to configure the IP addresses of your computer to be compatible with the device. The router supports DHCP server and it is enabled as default. Users that configure your IP address as “Obtain an IP address automatically” may skip the following IP configuration instruction. Note: 1. The default network setting of the device: IP address: 192.168.1.1 Subnet Mask: 255.255.255.0 DHCP Server: enabled 2. 3.
3. Choose Internet Protocol (TCP/IP) and click Properties. 4. You may choose “Obtain an IP address automatically”(recommend) to get IP address automatically or choose “Use the following IP address” to specify IP addresses manually. Please click the OK button after your configuration.
Management Wireless Router configuration setup In order to make the whole network operate successfully, it is necessary to configure the Wireless Router through your computer has a WEB browser installed. Please follow up the steps listed below. 1. Double click the Internet WEB browser icon on your desktop screen (Netscape Communicator 4.0 and Internet Explorer 3.0 or update version) 2. Type 192.168.1.1 into the URL WEB address location and press Enter. 3. The Username and Password Required window appears.
4. The Graphic User Interaface After the password authorization, the Setup Wizard shows up as the home page of the Graphic User interface. You may click on each folder on left column of each page to get access to each configuration page.
Setup Wizard If you are using the router for the first time, you may follow the procedures of the setup wizard to do a step-by-step configuration. Note: The following instruction does an overall introduction to the Setup Wizard. For detail information to each item, please refer to instruction of each page. 1. To start the Setup Wizard, click the “Next” button to proceed. 2. Select your demanding operation mode and click “Next”.
3. Mark the check box to enable synchronizing time by NTP server. Select the religion you live and a NTP server by clicking the drop list then click “Next”. 4. Specify an IP address and subnet mask for connecting to the router in LAN.
5. Select a WAN access type for the router to connect to Internet. Fill in the parameters that required in each blank, and then click the “Next” button. Those parameters should be provided by your ISP. 6.
7. Click the drop list to select the encryption type for your wireless network. Fill in the parameters for the encryption type you select and click finish to complete configuration.
Operation Mode To select an operation mode for this router, click on the mode that you want to perform and click the button to execute.
Wireless Wireless Access Point builds a wireless LAN and can let all PCs equipped with IEEE802.11b/g wireless network adaptor connect to your Intranet. It supports WEP encryption and MAC address filter to enhance the security of your wireless network. Basic Settings You can set up the configuration of your Wireless and monitor the Wireless Clients associate with your AP.
Click button at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place) ž Active Wireless Client Table This is the window that pops up after clicking the “Show Active Clients” button. MAC Address MAC address of this active wireless station. Tx Packet The number of transmitted packets that are sent out from this active wireless station.
Advanced Settings You can set advanced wireless LAN parameters of this router. The parameters include Authentication Type, Fragment Threshold, RTS Threshold, Beacon Interval, Data Rate, Preamble Type, Broadcast SSID, IAPP and 802.11g Protection. We recommend not changing these parameters unless you know what changes will be there on this router. Configuration Wireless AP can associate with this Authentication Open System wireless router without WEP Type mode encryption.
The wireless client can associate with this wireless router by using any one of these two Modes. Auto Fragment Threshold To specifies the maximum size of packet during the data transition. The lower values you set, the worst performance it will be. RTS Threshold If the packet size is smaller the RTS threshold, the wireless router will not send this packet by using the RTS/CTS mechanism. Beacon Interval The period of time how long a beacon is broadcasted.
Security At the page, you can set up the WEP, WPA Encryption to ensure the security of your Wireless. Configuration Encryption To enable WEP, WPA, WPA2 and WPA2 Mixed encryption modes, select the option in the drop list. If you select none, any data will be transmitted without Encryption and any station can access the router. Use 802.1x Authentication To enable the 802.1x, Click the check box of the item.
WPA2 Cipher Suite Select the WPA2 Cipher Suite to be TKIP or AES Pre-Shared key Format To decide the format, select what you need in the drop list. Pre-shared Key Enter the Pre-shared Key according to the pre-shared key format you select.
Access Control To restrict the Number of Access authentication of Stations, Set up the control list in this page. Configuration Wireless Access Click on the drop list to choose the access control mode. You may select “Allow listed” to Control Mode allow those allowed MAC addresses or select “Deny Listed” to ban those MAC addresses from accessing to this device. MAC Address & To set up the Value of MAC Address & Comment; enter the MAC Address and Comment Comment of station and click Apply Changes to save.
WDS Setting Wireless Distribution System allows the router to communicate with other APs wirelessly. To make it work, you must ensure that these APs and the Router are in the same Channel and add these APs MAC Address and Comment values into the WDS list. Don’t Forget to Enable the WDS by click the check box of “Enable WDS” and press “Apply Changes” button to save. To Delete the AP on the list, Click the check box in the select item and click the “Delete Selected”.
TCP/IP Setting LAN Interface Setup To set up the configuration of LAN interface, Private IP of you router LAN Port and Subnet mask for your LAN segment. Configuration IP address The IP of your Router LAN port (Default 192.168.1.1) Subnet Mask Subnet Mask of you LAN (Default 255.255.255.0) To give your LAN Client an IP, you have to enable “DHCP Server”. If not, manual setting up your client IP DHCP Server is necessary when you want to use the router as your client’s default gateway.
WAN Interface Setup This page allows users to configure those parameters for connecting to Internet. You may select the WAN Access Type from the drop list and configure parameters for each mode. Static IP Mode IP Address, Subnet Mask Fill in the IP address, Subnet Mask and Default Gateway and Default Gateway that provided by your ISP. DNS 1, 2 and 3 To specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3.
PPPoE Mode User Name, password and service name Connection Type Idle Time: MTU Size Fill in the User Name, password and service name that provided by your ISP. “Continuous” is for Always keep connection “Connect on demand” is for bill by connection time. You can set up the Idle time for the value specifies the number of time that elapses before the system automatically disconnects the PPPoE session. “Manual” To connect to ISP, click “Connect” manually from the WEB user interface.
PPTP Mode IP Address, Subnet Mask, Fill in the IP address, Subnet Mask, Server IP Address, Server IP Address, User User Name and password that provided by your ISP. Name and Password MTU Size To Enable the Maximum Transmission Unit of Router setup. Any packet over this number will be chopped up into suitable size before sending. Larger number will enhance the transmission performance. Enter your MTU number in the text-box to set the limitation.
Common configurations for WAN interface There are some settings are able to be configured on each WAN access types: Enable Web Server Access on WAN from port Enable IPsec pass through on VPN connection Enable PPTP pass through on VPN connection Enable L2TP pass through on VPN connection Clone MAC Address To Enable the user to access this Router through Internet, Enter the specific IP and the port number Mark the check box to enable IPsec pass through on VPN connection and clear the checkbox to disable.
Firewall Configuration Port Filtering The firewall could not only obstruct outside intruders from intruding your system, but also restricting the LAN users. Port Filtering To restrict certain type of data packets from your LAN to Internet through the Router, add them on the Current Filtering Table. Configuration STEPS 1. Click the check box of “Enable Port Filtering” to enable the function. 2. Enter the Port range (EX 25-110), Protocol (UDP/TCP), and comment (EX. E-Mail) 3.
IP filtering The Wireless Router could filter the outgoing packets for security or management consideration. You can set up the filter against the IP addresses to block specific internal users from accessing the Internet. Configuration STEPS 1. Click the check box of “Enable IP Filtering” to enable the function. 2. Enter the specific Local IP address (EX 10.10.3.9), Protocol (UDP/TCP), and comment (EX. Peter) 3.
MAC filtering The Wireless Router could filter the outgoing packets for security or management consideration. You can set up the filter against the MAC addresses to block specific internal users from accessing the Internet. Configuration STEPS 1. Click the check box of “Enable MAC Filtering” to enable the function. 2. Enter the specific MAC address (EX 00:0e:b6:a8:72), and comment (EX. Peter) 3.
Port forwarding The Port Forwarding allows you to re-direct a particular range of service port numbers (from the Internet/WAN Ports) to a particular LAN IP address. It helps you to host some servers behind the router NAT firewall. Configuration STEPS 1. Click the check box of “Enable port forwarding” to enable the function. 2. Enter the specific IP address (EX 10.10.10.10), Protocol (UDP/TCP), Port range (EX 25-110), and comment (EX. E-Mail) 3.
URL Filtering The URL Filter allows users to prevent certain URL from accessing by users in LAN. This filter will block those URLs that contain certain keywords. Configuration STEPS 1. Click the check box of “Enable URL Filtering” to enable the function. 2. Enter the URL that is going to be banned. 3. To Delete the URL on the table, Click the check box in the select item and click the “Delete Selected”. If you want to delete all URLs on the table, click “Delete All” to remove all of them.
Virtual DMZ The virtual DMZ is used to enable protocols, which need to open ports on the router. The router will forward all unspecified incoming traffic to the host specified in this page. To configure it, enter the Host IP (private IP address) and Click “Apply changes” to enact the setting.
Management Status In the home page of the Wireless Router, the left navigation bar shows the options to configure the system. In the right navigation screen is the summary of system status for viewing the configurations. l System Uptime The period that you power the device on. Firmware Version The version of the firmware applied on this device.
Channel Number The channel used by the wireless LAN. All devices in the same wireless LAN should user the same channel Encryption The security encryption status of this wireless network BSSID The Basic Service Set Identity of this router.(This parameter is the same as the MAC address of LAN port) Associated Clients The number of associated clients.
Statistics On this page, you can monitor the sent & received packets counters of wireless, Ethernet LAN, and Ethernet WAN. To see the latest report, click refresh button. DDNS This page allows users to connect to DDNS. To enable DDNS, Mark the “Enable DDNS” checkbox. Select the service provider from the drop list. Fill in domain name, username, and password. Click the “Apply Change” button after configuration.
Time Zone Setting This page allows users to configure the time of the router. To specify manually, fill in the blanks in “Current Time” and click the “Apply Change” button. To synchronize time from a timeserver, please mark the “Enable NTP client update” checkbox, select a NTP server from the drop list or manually enter a NTP server. Click the “Apply Change” button after your configuration. System Log This System Log page shows the information of the current activities on the router.
Upgrade Firmware To Upgrade Firmware, STEPS 1. Click “browse…” button to select the firmware you want to upgrade. 2. Click Upload to start the upgrade process. Please don’t close the WEB-browser and wait for process to complete. When Upgrade is completed, you can start to use the router.
Save and Reload Settings To save setting to file, click “Save...” button. To load setting from file, 1. Click “Browse…” on the to select the file 2. Click upload to start the process and wait for it to complete To reset setting to Default, click reset to start the process and it will be completed till the status LED start blinking. Password To set up the Administrator Account information, enter the Username, New password, and reenter the password on the text box.
Product Specifications IEEE802.3, 10BASE-T IEEE802.3u, 100BASE-TX Standard IEEE802.3x full duplex operation and flow control IEEE802.11b wireless LAN infrastructure IEEE802.11g wireless LAN infrastructure 1 * WAN port Interface 4 * 10/100 RJ-45 Fast Ethernet switching ports Antenna: 802.11b/g wireless reverse SMA detachable WAN Connection Ethernet 10/100 Mbps RJ-45 (10BASE-T): Category 3,4,5 UTP Cable Connections RJ-45 (100BASE-TX): Category 5 UTP 802.11b: 1, 2, 5.5 and 11Mbps Network Data Rate 802.
