User's Manual
Table Of Contents
- Chapter I: Product Information
- CHAPTER II: Driver Installation and Configuration
- 2-1 Network Adapter Installation
- 2-2 Connect to Wireless Access Point
- 2-2-1 Using Realtek Utility
- NOTE: If you insert the USB wireless network adapter into an USB 3.0 port and connect to an 11ac AP, device driver will doing auto USB mode switch and shown the message as below photo, or you will heard sounds of USB insert or unplug, this is the norm...
- 2-2-2 Using Windows Zero Configuration
- 2-3 Connection Profile Management
- 2-3-1 Add a New Profile
- 2-3-2 Remove an Existing Profile
- If you have added a profile before, and you wish to change the content of the profile, you can use this function. Please select a profile from the list first, then click ‘Edit’ button. You’ll be provided with the contents of selected profile, and you ...
- 2-3-4 Make a Copy of an Existing Profile
- 2-4 View Network Statistics, General Information, and Status
- 2-4-1 General Information
- 2-4-2 Status
- 2-5 Miscellaneous Settings
- 2-6 Establish a Secure Connection with AP by WPS
- 3-1 Switch to AP Mode and Station Mode
- 3-1-2 Setup Soft-AP Security
- 3-2 Advanced Settings
- 3-3 Wireless Statistics
- 3-4 Internet Connection Sharing (ICS)
- 4-1 Hardware Specification
- 4-2 Troubleshooting
- 4-3 Glossary
VI
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSSs. Operation is subject
to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le present appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisee aux deux conditions
suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique subi, meme
si le brouillage est susceptible d’en compromettre le fonctionnement.
Caution:
(i) The device for operation in the band 5150-5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) For devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the
equipment still complies with the e.i.r.p. limit;
(iii) For devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the band 5725-5850 MHz shall be such that the equipment still complies
with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as
appropriate; and
The high-power radars are allocated as primary users (i.e. priority users) of the bands
5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference
and/or damage to LE-LAN devices.
DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350
MHz, 5470-5600MHz, and 5650-5725MHz.
Avertissement:
(i) Le dispositif fonctionnant dans la bande 5150-5250 MHz est reserve uniquement
pour une utilisation a l’interieur afin de reduire les risques de brouillage prejudiciable
aux systemes de satellites mobiles utilisant les memes canaux;
(ii) Le gain maximal d’antenne permis pour les dispositifs avec antenne(s) amovible(s)
utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer a la