Manual

ManualsBrandsNetwork Technologies ManualsComputer AccessoriesRACKMUX-UW15-4USB

ST-C5MK-VESA

VESA MOUNTING BRACKET KIT

Installation Instruction

The ST-C5MK-VESA is a VESA Mounting Bracket Kit that allows an NTI extender (XTENDEX) to be easily mounted to the back of a

flat panel monitor enabling simple and clean cable routing and saving valuable desk space. The ST-C5MK-VESA is provided with

two sets of mounting holes compliant to VESA 75mm and 100mm mounting hole patterns. Two sets of standoffs allow the NTI

XTENDEX to be attached such that cables can approach from any of 4 directions. See the chart below for XTENDEX models that

can be mounted using the ST-C5MK-VESA.

Compatible XTENDEX Models Where to find:

ST-C5x-600: Remote Units only

http://www.networktechinc.com/cat5.html

http://www.networktechinc.com/cat5-vga.html

ST-C5x-300: Remote and Local Units

http://www.networktechinc.com/cat5-300.html

http://www.networktechinc.com/cat5-300-vga.html

ST-C5x-1000: Remote Units only

http://www.networktechinc.com/cat5-1000.html

http://www.networktechinc.com/cat5-1000-vga.html

Installation

1. If the existing monitor support arm bracket (see picture on page 3 for reference) has not already been removed from the monitor,

remove it now.

2. Place the large ST-C5MK-VESA mounting bracket between the support arm bracket and the monitor. The holes in the support

arm bracket will line up with either the holes in the VESA 75mm pattern or the 100mm pattern (see image below). Reapply the screws

to secure the support arm bracket and the large ST-C5MK-VESA mounting bracket to the monitor. Be sure to tighten the screws

securely.

Hole pattern for

75mm mounting

Hole pattern for 100mm mounting

Rear View of LCD monitor

Place VESA mounting bracket between the monitor mounting

plate and the monitor. Use either the 75mm hole pattern or

the 100mm hole pattern.

Standoffs for mounting the XTENDEX

Summary of content (3 pages)

PAGE 1
ST-C5MK-VESA VESA MOUNTING BRACKET KIT Installation Instruction The ST-C5MK-VESA is a VESA Mounting Bracket Kit that allows an NTI extender (XTENDEX) to be easily mounted to the back of a flat panel monitor enabling simple and clean cable routing and saving valuable desk space. The ST-C5MK-VESA is provided with two sets of mounting holes compliant to VESA 75mm and 100mm mounting hole patterns. Two sets of standoffs allow the NTI XTENDEX to be attached such that cables can approach from any of 4 directions.
PAGE 2
Place bracket on XTENDEX over screws and slide into keyhole slot. Tighten screws on back of XTENDEX Loosen screws on back of XTENDEX 3. Loosen the two screws on the back of the XTENDEX and apply the small mounting bracket supplied with your kit. Slide the bracket so that the screws on the XTENDEX are captured in the slots in the bracket. Tighten the screws. Note: Some models of NTI XTENDEX instead have extra holes on the back for mounting this bracket and require two additional screws to be applied.
PAGE 3
ST-C5MK-VESA Existing support arm bracket XTENDEX Warranty Information The warranty period on this product (parts and labor) is two (2) years from the date of purchase. Please contact Network Technologies Inc at (800) 742-8324 (800-RGB-TECH) or (330) 562-7070 or visit our website at http://www.networktechinc.com for information regarding repairs and/or returns. A return authorization number is required for all repairs/returns. COPYRIGHT Copyright © 2008 by Network Technologies Inc. All rights reserved.