I NSTALLATI ON GU I D E
Intro To watch a video of the installation visit support.neur.io This booklet will guide an electrician or a professional installer through the typical installation process of the Neurio Sensor on a two-phase system (the most common power system in North America). If you have a one-phase, three-phase or solar system, please visit support.neur.io for instructions.
Steps to follow: CONTENTS OF NEURIO BOX Neurio Sensor Two (2) current transformers (CTs) Step 1 Step 6 Turn off main breaker Connect the antenna Step 2 Step 7 Remove breaker panel cover Check your work Step 3 Voltage cable Step 8 Replace panel cover Mount the sensor Two (2) self-drilling screws Antenna and cable One (1) marrette Step 4 Connect the voltage cable Step 9 Connect Neurio to WiFi Step 5 Connect CTs ½" and ¾" antenna mounts Two (2) wiretaps Neurio breaker sticker If you get
Step 1 Turn off the main breaker in your electrical panel. OFF NOTE : If you have more than one electrical panel in your house, make sure Neurio is installed in the main one (the one that draws power directly from your utility).
Step 2 Remove the screws on the corners of the panel and remove the cover. After you do this, you should see the wires going into each breaker and main lines from the utility. If your panel has a secondary cover that hides the main utility line, please remove that as well. ! CAUTION: OFF BEFORE ! OFF FF O AFTER CAUTION: In some cases, even though main breaker is off, some parts of the panel could be still energized. Use caution.
Step 3 Find a suitable place in your panel where Neurio can fit. Then, using the supplied self-drilling screws, secure Neurio to your metal panel. CAUTION: Be sure to account for the length of the 4 foot CTs and the 2 foot voltage cable, and ensure that there is enough room on the sides of Neurio for the wires and antenna to connect to. NOTE : The self-drilling screws will need pressure to drill through the metal. OFFFF O OFF OFF OFFFF O MAX.
Step 4 ALTERNATE WIRING WITH WIRETAP 1 ) Connect the voltage cable to Neurio by inserting the connector into the matching port on the Neurio Sensor. 2 ) Connect the black wire to an empty 15 or 20amp breaker on the one phase of power. 3 ) Connect the red wire to an empty 15 or 20amp breaker on the other phase of power. 4 ) Connect the white wire to neutral bus bar, usually located next to the breaker. 5 ) Twist the marrette onto the blue wire and tuck into panel out of the way.
Step 5 1 ) Remove the top bracket of the CT by inserting your finger through the loop and pulling towards you. 2 1 CAUTION: Be sure to take care to not touch the exposed main line connections to the main breaker. 3 ) Insert the connector from the CT that's on the same phase as the black Neurio voltage wire into port labeled (1). Then insert the connector from the second CT into the port labeled (2). OFF OFF 2 ) Loop the CTs around each of the main power lines and attach the bracket to the CT again.
Step 6 1 ) Attach the antenna cable to left side of the Neurio Sensor. 2 ) Locate a free ½" or ¾" metal circular knockout in your panel and remove the metal tab to expose the hole. NOTE : If you are having troubles removing the knockout, use a hammer to gently tap the screwdriver to pry the knockout open. 3 ) Remove the nut at the end of the cable and insert the cable through either the ½" or ¾" antenna mount. based on the size of knockout hole.
Step 7 CHECK YOUR WORK Now the panel should look something like this: 1 ) Antenna 1 2 3 2 ) Antenna cable 4 3 ) Neurio Sensor 6 4 ) Voltage cable — the voltage cable should be connected to 2 breakers and the neutral bus bar 5 7 5 ) 2 Wire taps (optional) 6 ) 15A or 20A single-pole breaker on phase A 7 ) 15A or 20A single-pole breaker on phase B 8 ) Neutral bus bar 9 ) Main breaker 10 ) Mains service wires and 2 CTs, connected to ports #1 and #2 8 9 OFF OFF 10
Step 8 You're almost done. Replace the covers on your panel. Make sure to place the supplied Neurio breaker sticker next to the breaker that Neurio's black wire is connected to. Then turn the main breaker back on. ON If you don’t hear the tune acknowledging a successful installation, please visit support.neur.io for troubleshooting tips.
Step 9 Now that the Neurio Sensor has been installed, have the homeowner follow the instructions in the Welcome Guide to connect Neurio to their WiFi network and to create an account. WHAT DOES THIS WARRANTY COVER? Neurio Technology Inc.
QU ESTI ONS OR FEED BAC K? SUP P ORT. NEUR .