TECHNOLOGY FOR THE MIND NeuroTek Elite Series Standard Tac Quickstart Guide Important: Please read all instructions completely before operating this device ©NeuroTek 2020 Version 2.
FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Liability Disclaimer This product is a tool designed to assist the clinician in the administration of (EMDR). The purchaser/clinician agrees to accept full responsibility for any harmful results and/or undesirable consequences obtained from the use of this machine. The manufacturer of this machine shall not be held liable for adverse affects caused to clients resulting from the administration of EMDR or any other form of therapy using this machine.
Product Features Auditory Tone mode Dual Modality - Use auditory or tactile stimulation independently or together Adjustments for volume, speed (rate) and tactile intensity Range 1 – for 10 volume, speed (rate) and tactile intensity Adjustments LED Screen Range 1 – 10provides visual speed and auditory mode information Connectivity LED Screen provides visual speed and auditory mode information Headphone and pulser cable (6 feet) Connectivity Soothing alternative to eye movements Headphone and pulser cable (6
Standard Standard Tac Tac Quickstart Quickstart Guide Guide Thank you for purchasing the NeuroTek Elite Series Tac. The Standard Tac has and adjustment range of 1–10. 1 Insert the nonchargeable CR123A battery (included) or plug in the adapter Battery Bay ©NeuroTek 2020 Version 2.
Controls for Standard Tac Power/Enter/Increment Navigate Increment/Navigate Decrement/Navigate Navigate 2 Turn ON/OFF ON: Press and hold power/enter until screen activates. OFF: Press and hold power/enter until screen is blank. 3 Tactile and Audio Connect (Wired) Wired pulser port. Wired headset port. ©NeuroTek 2020 Version 2.
4 Quick Start o o o o To begin session, hold the middle button for approximately 5 seconds to turn the device on. Plug in your pulsers and or headset into the side of the Tac. If you have an EyeScan see #4 of the manual on how to pair the EyeScan to the Tac. If you don’t you can continue to the next step. On the main screen, you will see the words Resource (which is slower speeds), and Reprocessing (which is higher speeds). These are 2 preset profiles that you can use to get started.
5 Edit Profiles To edit the profiles, you would want to have all your accessories (the pulsers, headset and EyeScan if applicable) connected to the Tac in order to adjust the settings for all devices. Once they are connected, you would follow the following steps: o o o o o From the main menu, Select Profiles You will then see Resource (which is set at slower speeds) and Reprocessing (which is set at higher speed). Select Edit next to the one you want to change, and then select Start.
A. Turn on Tac by holding the center power button for 5 seconds B. Do you A have an EyeScan? If yes, continue below. If no, 6 Start Session see step C. A. Turn on Tac by holding the center power button for 5 o Ensure your EyeScan is turned on. On your Tac, seconds Select thenIfselect Wirelessbelow. Devices. B. Do you haveSettings, an EyeScan? yes, continue If no, Your see step C. tac will automatically scan for wireless devices.
C. Connect your wired devices to your Tac; o You can plug in the headset, the pulsers, or both. The main menu C. Connect yourwwired devices your Tac: will show hat devices are to connected. o You can plug in the headset, the pulsers, or both. The main menu will show what devices are connected. Resources Reprocessing Pulser Headphones EyeScan Profiles Settings D.
End, Restart, or Pause a Session A session can be started three ways 1) Use the Start Session button in the Main Menu 7 End, Restart, or Pause a Session 3) Choose any device from the Main Menu and use Start Stopping a session suspends it but gives the user the choice to continue or end the session Restart will restart the session The session can be Paused and, when pressed, the button will read Play which will continue the current session ©NeuroTek 2020 Version 2.
Other Settings for Tac 8 Other Setting for Tac Select to turn Power Savings Mode ON/OFF Power Savings Arrow to the left to adjust the screen’s brightne Arrow to the left to adjust the screen’s brightness. #7 End, Restart, or Pause a Session (we can keep this) ju Rechargeable Battery – Select this option if you have picture. purchased a rechargeable version of the battery CR123A. You must also purchase a charger to charge the battery outside of the device.
Troubleshooting Guide Troubleshooting Guide can do a reset by inserting a paper clip into the small hole at the bottom of the Tac. When you feel the button click, release can do a reset by inserting a paper clip into the small hole at the bottom of the Tac. When you feel the button click, release The reset button is located in the same place on the bottom of all Tacs. The reset button is located in the same place on the bottom of all Tacs.
Troubleshooting Guide o o If you put in a disposable battery, and the battery level still shows low battery, please check the settings to ensure that the Disposable Battery option is selected. It will be in black letters if selected. To extend the life of your battery, please turn on the power save mode under settings. It will dim your screen after 30 seconds of inactivity. To light the screen back up, simply press a button.
©NeuroTek 2020 Version 2.
17116 Journeys End Dr., Odessa, FL 33556 727-372-0104 www.neurotekcorp.com ©NeuroTek 2020 Version 2.
