Manual

ManualsBrandsNeuspeed ManualsCar65.02.67

NEUSPEED® • 3300 Corte Malpaso • Camarillo, CA 93012 • 805.388.7171 • 805.388.0030 FAX • information@neuspeed.com • Visit us on the web…http://www.neuspeed.com

PARTS LIST: TOOLS REQUIRED:

1 – P-FLO BRACKET 1 – INTAKE TUBE 1- SILICONE REDUCER HOSE 1 – NEUSPEED AIR FILTER SCREWDRIVER PHILLIPS SCREWDRIVER 5mm HEX KEY WRENCH

1 – SS #52 HOSE CLAMP 1 – SS #56 HOSE CLAMP 4 – SS CAP BOLT M6x12mm 4 – SS M6 NYLOC NUT 6mm HEX KEY WRENCH 10mm WRENCH 11mm WRENCH

1 – SS ACORN NUT 1 – SERRATED FLANGE NUT 1 – SUPPORT BRACKET - Short 1 – RUBBER ISOLATOR RATCHET DRIVER 10mm SOCKET T25 TORX

1 – WEATHER STRIPPING 1- SUPPORT BRACKET - Long SPRING CLAMP PLIERS DRILL ¼” DRILL BIT

1. Remove air intake duct at radiator support. There are (2)

T25 Torx screws on top of support.

2. Unclip sound amplifier hose attached to air filter box lid.

3. Disconnect electrical connector at MAF sensor.

4. Using spring clamp pliers, disconnect air intake tube from

MAF sensor.

5. Unbolt left front corner of lower air box using 5mm hex key

wrench.

6. Remove air box lid using Phillips screwdriver then air filter.

7. Lift off lower air box from the two rubber mounting

grommets and remove from vehicle. Use WD-40 or

equivalent on grommets to ease removal.

8. Install and tighten supplied rubber isolator onto left front air

box mounting bracket.

9. Using 10mm socket, temporally remove the front bolt on air

box mounting bracket.

10. Install supplied support bracket to air box mount using

original bolt (from step 9), then to stud on underside of

mount for rubber grommet using supplied M6 flange nut.

Now tighten nut and bolt.

P-FLO KIT AIR INTAKE SYSTEM – PART #65.02.67

Fits: 2009-11 Audi TTS

Summary of content (3 pages)

PAGE 1
P-FLO KIT AIR INTAKE SYSTEM – PART #65.02.67 Fits: 2009-11 Audi TTS PARTS LIST: 1 – P-FLO BRACKET 1 – SS #52 HOSE CLAMP 1 – SS ACORN NUT 1 – WEATHER STRIPPING 1. 1 – INTAKE TUBE 1 – SS #56 HOSE CLAMP 1 – SERRATED FLANGE NUT 1- SUPPORT BRACKET - Long 1- SILICONE REDUCER HOSE 4 – SS CAP BOLT M6x12mm 1 – SUPPORT BRACKET - Short Remove air intake duct at radiator support. There are (2) T25 Torx screws on top of support. 2. Unclip sound amplifier hose attached to air filter box lid. 3.
PAGE 2
11. Using needle nose pliers squeeze pin to remove one of the sound amplifier hose clamps from air filter box lid. 14. Unscrew and pull-out MAF from air box lid. 12. Install clamp back onto hose and mark side of engine cover. Remove engine cover off it’s rubber mounts by lifing up. Drill a ¼” hole and deburr both sides of hole. 15. Reinstall MAF to factory tube. 17. Remove rubber grommet from lower air box and install into hole of P-Flo bracket as shown. 19.
PAGE 3
20. Remove rubber grommet from lower air box and install into hole of supplied support bracket – long. 23. Install weather strip on to edge of P-flo bracket, then install NEUSPEED filter. 21. Install bracket onto rear mount for factory air box and bolt to hole on P-Flo bracket with SS screw and lock nut supplied. 24. Installation is now complete. Double-check tightness of all connections and test drive carefully. NOTE: Double-check all clamps and connections after 1 week of driving. 22.