Installation Guide

Pergola Additional Materials List
Hardware (in plastic bag)
NOTE: WE HAVE INCLUDED 10% EXTRA SCREWS BEYOND WHAT IS IDENTIFIED BELOW
All Screws Included with this Kit are Self-Auguring.
A. Tube of Vinyl Weld Glue (2) - 20000
B. 5/8” Self-Auguring Stainless Steel Screws (72) - 20016 (to lock Louver
Assembly to Steel Holder brackets )
C. 5/8” Self-Auguring Stainless Steel Screws (24) - 20016 (to lock Rafter Hangers to Rafter )
D. 1 1/2” Self-Auguring Stainless Steel Screws (36) - 20005 (for Beam and Rafter Joiners )
E. 1 1/2” Self-Auguring Stainless Steel Screws (24) - 20005 (to lock the Rafter Hangers to Attached Beam)
F. 2 1/2“ Self-Auguring Stainless Steel Screws (2) - 20009-1 (to fasten Turn Bar Holder to post)
G. 2 1/2“ Self-Auguring Stainless Steel Screws (16) - 20009-1 (to lock Top and Bottom Columns to Wood Posts)
H. 4” Self-Auguring Stainless Steel Screws (12) - 20006 (to lock Rafters to the Beams)
I. 4” Self-Auguring Stainless Steel Screws (24) - 20006 (to lock Beams and Rafters to Posts)
J. 9” Stainless Steel Bolt Assembly with Nuts and Washers (2) - 20035 (to lock the Column Tops to Beams)
K. Turn Bar Holder (1) * Found in Box 7 - 10957
Extra Materials You will Need
(Purchase separately from www.newenglandarbors.com or retailer of our products)
If Mounting Pergola on Concrete or Wood Deck
L. 4x4x8 Pressure-Treated Wood Posts (2) (purchase at local building center)
M . 4x4 Bolt Down Bracket Kit - Do not use the Bolt Down Bracket system for installing
the pergola over concrete pavers, patio stones, or interlocking bricks.
(purchase from www.newenglandarbors.com or a retailer of our products)
Refer to bolt down bracket instructions for hardware requirements,
as they pertain to your application:
If mounting pergola onto an existing concrete surface:
• 1/2“ x 3 1/2” x 12“ Wood Shims (16) - (Can be cut, using 1/2” plywood)
• 1/4” x 2 3/4“ Cement Screws - Countersunk Head (6)
• 3/16” Concrete drill bit. Minimum 3“ long (1)
If mounting pergola onto a wooden/composite deck with AN ACCESSIBLE UNDERSIDE:
• 1/2“ x 3 1/2” x 12“ Wood Shims (16) - (Can be cut, using 1/2” plywood)
• 1/4” x ?“ Bolts and Nuts - Countersunk Head (6) (Length depends on blocking material)
• 1/4” Washers (6)
• 1/4” Wood drill bit. Minimum 3“ long (1)
If Mounting Pergola in Ground
N. 4x4x12 Pressure-Treated Wood Posts (2) Cut down to 11’ (purchase at
local building center)
O. Concrete Ready Mix (2) (purchase at local building center)
Rafter/ Beam Support (Required)
P. 2x6x14 Pressure-Treated Boards for Beams and Rafters
(to be cut down to 13’) (1) (purchase at local building center)
Q. 2x6x12 Pressure-Treated Boards for Beams and Rafters (8) (purchase at
local building center)
R. 2x6x6 Pressure-Treated Boards (2) (purchase at local building center)
S. 3/8” x 3 1/2” Lag Screw with Washers (6) (purchase at local building center)
T. 3/8“ x 3 1/2” Lag Screws (for wood wall) or Anchor Screws (for brick
or concrete wall) (6) (purchase at local building center, also purchase drill bit)*
*) Please consult your local building center for mounting anchors. These second set
of screws will be used to mount your wood beam / ledger onto your structure. Refer to page 12 for more information.
Not to Scale
6
www.newenglandarbors.com
J
H I
GF
D E
CB
K
A
O
CONCRETE - Ready Mix
Purchase Separately
Purchase Separately
M
TS
P
Purchase
Separately
L
Purchase
Separately
N
Purchase
Separately
Q
Purchase
Separately