User Manual

ManualsBrandsNew England Arbors ManualsKitchenFlorence 42 in. x 86 in. White Vinyl Arbor

Check Box for These Contents

In the event of missing or defective parts please call our customer service dept. at

1 800 282 9346 (

Mon. to Fri. 8:00 AM to 4:00 PM EST).

1. Posts (4)

2. Post Caps (4)

3. Arches (4)

4. Arch Keystones, Inserts, and Lids (2)

5. Keystone Bottom Plates (2)

6. Arch Rafters (6)

7. Side Panel Horizontal Bent Top Rails (2)

8. Side Panel Horizontal Mid-Rails (2)

9. Side Panel Horizontal Spindles Short (8)

10. Side Panel Vertical Spindles Long - Left (2)

11. Side Panel Vertical Spindles Short - Middle (2)

12. Side Panel Vertical Spindles Long - Right (2)

13. Side Panel Horizontal Bottom Rails (2)

14. Ground Anchoring Stakes (4)

15. 1 1/2 Self-Auguring Stainless Steel Screws (24)

Tools You Will Need

• Cordless Drill

• Hammer

• Tape Measure

• Level

• Stool or Short Ladder

• Shovel

General Information

• Read Instructions through carefully before

beginning assembly.

• When assembling components, place on a non-abrasive surface

(i.e. shipping box) to avoid scratching.

• We recommend an area approx 10ft.x 8ft. for unobstructed assembling.

• You should not need to use excessive force when assembling components.

The Florence Arbor

Please read through before starting assembly.

ASSEMBLY INSTRUCTIONS

89.6 in

42 in

49 in

20 in

24 in

4 6

Not to Scale

81.8in

IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.

V2.1/111015

www.newenglandarbors.com

Summary of content (4 pages)

PAGE 1
A S S E M B LY I N S T R U C T I O N S The Florence Arbor www.newenglandarbors.com 89.6 in 81.8in 20 in 42 in 24 in 49 in Please read through before starting assembly. IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS. Check Box for These Contents In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 4:00 PM EST). 1. Posts (4) 2. Post Caps (4) 3. Arches (4) 4. Arch Keystones, Inserts, and Lids (2) 5.
PAGE 2
STEP ONE www.newenglandarbors.com Assemble the Arch System tone Keys 1 Inser t Insert arches into arch keystone ensuring they terminate flush to the internal connector. The tabs sticking out of the internal connector should fit outside the arches. Ensure that the arches are orientated properly as per illustration. 2 Fasten the arch system to the keystone by installing the screws into the 2 pre-drilled holes provided.
PAGE 3
STEP T WO Assemble the Side Panels 1 Insert the four short horizontals spindles into one long LEFT vertical spindle, one long RIGHT vertical spindle and one short vertical spindle that is positioned in the middle. www.newenglandarbors.com NOTE: Some of the horizontal rails have locking tabs located at both ends. Once inserted and pushed into the routered holes, they will lock into place. Right Left 2 Lay out the horizontal bottom rail and insert three vertical spindles.
PAGE 4
A STEP FOUR 1 Arbor Installation Arbors must be well secured to prevent tipping over from wind load etc. We have provided four ground anchors for securing the arbor either into the ground or a concrete footing. In some cases it may be acceptable to secure the arbor to an existing structure such as a fence post. If you are installing your arbor on concrete or a deck, see your hardware store for the appropriate galvanized bracketing hardware.